Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add QCA new status vendor attribute
QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE
to indicate the TWT session termination due to power save
exit request from userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attribute to indicate the bandwidth to be used
for spectral scan operation:
- QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD to fetch thermal
statistics for different temperature levels from the driver to
userspace. The statistics will be stored in the driver/firmware for
predefined temperature levels and will be reported to userspace when
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD is sent with the command type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS.
The thermal statistics can be cleared from userspace by sending a
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD command with the type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Determine if the TDLS peer supports TDLS in 6 GHz band based on the HE 6
GHz Band Capabilities element received in the TDLS Setup Response frame.
Indicate the peer's HE 6 GHz capabilities to the driver through
sta_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attributes to configure the driver to enable/disable the
Broadcast TWT support and Rx Control Frame To MultiBSS support in HE
capabilities information field. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF
TWT attribute to use it in TWT setup command to pass TSF value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attribute to configure the driver to enable/disable
the BSS max idle period support. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use scan
request BSSID value in Probe Request frame RA(A1) for scan.
This attribute is used for testing purpose.
The driver saves this configuration and applies this setting to all user
space scan requests until the setting is cleared. If this configuration
is set, the driver uses the BSSID value from the scan request to set the
RA(A1) in the Probe Request frames during the scan, else the broadcast
address is set in the Probe Request frames RA(A1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend the previously 5 GHz specific 80 and 160 MHz channels helper
functions to support 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Introduce P2P 6 GHz band capable information in Device Capability
Bitmap of P2P Capability sub-attribute.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add QCA vendor interface to configure the driver which transport mode to
use for sending CFR data to userspace. Currently, relayfs and netlink
event modes are supported.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use Data or
Management frames for keep alive data. This attribute is used for
testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute to configure the driver to transmit the
Data frames with ER SU PPDU type format. This attribute is used
for testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS
to configure FT over DS to the driver/firmware.
Signed-off-by: Vinita S. Maloo<vmaloo@codeaurora.org>
Add QCA interface to specify the RSSI thresholds separately for candidate
APs from different bands.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Mention that for AP mode this attribute is required in
response for TWT SET, TWT GET, TWT SUSPEND, and TWT
TERMINATE. And is required in request for TWT GET, and
TWT TERMINATE.
For STA mode, the usage of this attribute remains unchanged.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
This moves the implementation closer to the current IEEE 802.11 standard
since B15 of Frame Control field was renamed to +HTC to match it newer
uses.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface for userspace to get information of usable
channels for different interface types from the driver/firmware.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Get the DPP Relay Controller context from the list of configured
Controllers based on the correct hostapd callback context. This is
needed to pick the correct hostapd interface for sending out the
response over air, e.g., when the same hostapd process controls a 2.4
GHz only and a 5 GHz only interface.
Signed-off-by: Disha Das <dishad@codeaurora.org>
The firmware rejects the TWT setup request when scan is in
progress. Extend enum qca_wlan_vendor_twt_status to represent new
reason code for it.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Define a new reason code in enum qca_wlan_vendor_hang_reason,
QCA_WLAN_TASKLET_CREDIT_LATENCY_DETECT, for tasklet/credit latency
detection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a QCA vendor command to configure the concurrent connection
policies when multiple STA interfaces are (getting) active.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add timeout to close incomplete DPP relay connections. This is needed to
avoid getting stuck with old entries that prevent new connections from
getting started.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This changes the Send-Confirm value for the first SAE Confirm message to
be 1 instead of 0 for all cases to match the design shown in IEEE Std
802.11-2020, Figure 12-4 (SAE finite state machine).
Sc is defined to be "the number of SAE Confirm messages that have been
sent" which is a bit vague on whether the current frame is included in
the count or not. However, the state machine is showing inc(Sc)
operation in all cases before the "2" event to build the Confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The 6 GHz band operating class 136 is defined to use 20 MHz bandwidth.
Return the value accordingly from center_idx_to_bw_6ghz() to cover this
special case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
It is more convenient to see the exact error in the debug log instead of
getting noted that something was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an attempt of making the code easier to understand for static
analyzers. The helper functions were already verifying that these IEs
are fully within the memory buffer, but that may not have been clear
enough for automated analysis.
Signed-off-by: Jouni Malinen <j@w1.fi>
BRCM vendor command used to trigger ACS scan. After ACS finished,
DHD driver will send results by event BRCM_VENDOR_EVENT_ACS.
Signed-off-by: Xinrui Sun <xinrui.sun@broadcom.com>
Determine if the TDLS peer is HE capable based on HE Capability element
received in the TDLS Setup Response frame. Indicate the peer's HE
capabilities to the driver through sta_add().
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
