Especially when multiple BSSes are used with ACS, number of the error
paths were not cleaning up driver initialization properly. This could
result in using freed memory and crashing the process if ACS failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"parallel-vm.sh <number of VMs> [arguments..]" can now be used to run
multiple VMs in parallel to speed up full test cycle significantly. In
addition, the "--split srv/total" argument used in this design would
also make it possible to split this to multiple servers to speed up
testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to debug wpa_supplicant behavior when reporting
20/40 MHz co-ex information based on OBSS scans.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 40 MHz intolerant bit needs to be checked before skipping the BSS
based on the channel already being in the lost (which could have
happened due to another BSS that does not indicate 40 MHz intolerant).
This fixed the 20/40 MHz co-ex report to indicate 20 MHz request
properly if there are both 40 MHz tolerant and intolerant BSSes on the
same channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ht_capab=[40-INTOLERANT] can now be used to advertise that the BSS is 40
MHz intolerant to prevent other 20/40 MHz co-ex compliant APs from using
40 MHz channel bandwidth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the PMK-R1 needs to be pulled for the R0KH, the previous
implementation ended up rejecting the over-the-air authentication and
over-the-DS action frame unnecessarily while waiting for the RRB
response. Improve this by postponing the Authentication/Action frame
response until the pull response is received.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional third argument to the test case functions can now be used
to receive additional parameters from run-tests.py. As the initial
parameter, logdir value is provided so that test cases can use it to
review the debug logs from the test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
This moves some of the p2p_prepare_channel_best() functionality into
separate helper functions to make the implementation easier to read.
Signed-off-by: Jouni Malinen <j@w1.fi>
The main WPS code rejects WEP parameters, so this code is not used and
can be commented out from WPS 2.0 builds. This is similar to the earlier
commit that commented out in-memory update.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 94b84bc725 missed one path where
p2p->op_reg_class should have been updated. Set this to 81 during
operating channel selection from 2.4 GHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports full offloading of DFS operations, do not disable
a channel marked for radar detection. The driver will handle the needed
operations for such channels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses a QCA vendor extension to determine if the driver supports
fully offloaded DFS operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The main WPS code rejects WEP parameters, so this code is not used and
can be commented out from WPS 2.0 builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not select pre-configured channel as operating channel preference if
it is unavailable maybe due to interference or possible known
co-existence constraints, and try to select random available channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It does return something: the reference of the request, as an integer,
which can be used then with ServiceDiscoveryCancelRequest to get
canceled.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
p2p_sd_cancel_request returns -1 in case of error, so does
wpas_p2p_sd_cancel_request.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There was possibility that the current channel in Beacon information
element was incorrectly set. This problem was easily observed when
primary and secondary channel were switched and then some of hostapd
settings (for example password) were changed using WPS External
Registrar. This caused hostapd_reload_config() function overwrite the
current channel information from config file.
This patch prevents this situation and does not allow to overwrite
channel and some other settings when config is reloaded.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Whenever an ongoing GO Neg has failed, due to interface init, the P2P
Device should cancel timeouts and issue wpas_p2p_group_formation_failed,
so the other peer detects faster group formation has failed.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Some old device need to set p2p_no_group_iface=1 to set up a P2P
connection, so add a D-Bus interface to configure it.
Signed-off-by: Guoqiang Liu <guoqiang.liu@archermind.com>
It was possible for hapd->wps_beacon_ie and hapd->wps_probe_resp_ie to
be set if WPS initialization in hostapd failed after having set these
parameters (e.g., during UPnP configuration). In addition, many of the
other WPS configuration parameters that were allocated during the first
part of the initialization were not properly freed on error paths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
