Commit graph

319 commits

Author SHA1 Message Date
Veerendranath Jakkam
6c7b2be424 SAE: Send real status code to the driver when AP rejects external auth
Send the status code from the AP authentication response instead of
sending the hardcoded WLAN_STATUS_UNSPECIFIED_FAILURE when the external
SAE authentication failure is due to an explicit rejection by the AP.
This will allow the driver to indicate the correct status in connect
response.

For example, an AP can send WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA in
SAE authentication response. With this change the driver gets the real
status for the SAE authentication failure and it can fill the correct
status in the connect response event.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-05-05 13:08:16 +03:00
Nicolas Norvez
16b5ea9e91 Reject authentication start during BSS TM requests
After receiving a BSS Transition Management request,
wpa_supplicant_connect() will abort ongoing scans, which will cause scan
results to be reported. Since the reassociate bit is set, this will
trigger a connection attempt based on the aborted scan's scan results
and cancel the initial connection request. This often causes
wpa_supplicant to reassociate to the same AP it is currently associated
to instead of the AP it was asked to transition to.

Add a bss_trans_mgmt_in_progress flag to indicate that we're currently
transitioning to a different AP so that we don't initiate another
connection attempt based on the possibly received scan results from a
scan that was in progress at the time the BSS Transition Management
request was received.

This is the equivalent of commit 5ac977758d ("Reject authentication
start during explicit roam requests") for the roaming scenario.

Signed-off-by: Nicolas Norvez <norvez@chromium.org>
2022-01-11 17:57:38 +02:00
Shivani Baranwal
3f8c83a65e SAE: Make sure BSS entry is available to determine RSNXE information
wpa_supplicant may use wrong SAE authentication method if it doesn't
have the scan result for the target BSS since RSNXE information is not
available.

For example, STA might use the hunting-and-pecking loop method for SAE
authentication even though AP supports SAE H2E and STA is configured
with sae_pwe=2.

This is possible in cases like EXTERNAL_AUTH triggered by the driver
during roaming. To avoid this update scan results to fetch the target
BSS scan result from the driver.

Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
2021-12-21 00:06:19 +02:00
Ernst Sjöstrand
36973aac2c SME: No need for OBSS scan if HT40 is disabled
Signed-off-by: Ernst Sjöstrand <ernst.sjostrand@verisure.com>
2021-12-11 13:10:58 +02:00
Matthew Wang
e480321f8c Revert "STA OBSS: Add check for overlapping BSSs"
This reverts commit 3204795d7a.

The commit adds an additional check that checks for overlapping BSSs in
addition to the existing 40 MHz intolerance subfield checks. The commit
cites IEEE Std 802.11-2016, 11.16.12, which defines the proper behavior
for a 20/40 MHz HT STA and AP, but the standard actually doesn't say
anything about overlapping BSSs. Specifically, the standard states that
the only BSSs that belong in the Intolerant channel report are those
that satisfy trigger event A, defined as channels with BSSs that don't
contain the HT capabilities element (which wpa_supplicant already did
before). Note that we also include channels with BSSs that have the 40
MHz intolerance bit set in the Intolerant channel report.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2021-12-11 13:05:47 +02:00
Jouni Malinen
914a2f518f SAE: Report authentication rejection over control interface
CTRL-EVENT-AUTH-REJECT reporting was previously skipped when going
through SAE-specific Authentication frame handling. Add this event here
as well to be more consistent with control interface events.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-07-14 18:18:47 +03:00
Jouni Malinen
663e190b72 SAE: Remove now unused password identifier argument from non-H2E case
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-04-10 12:12:54 +03:00
Matthew Wang
5ac977758d Reject authentication start during explicit roam requests
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.

Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2021-03-06 10:59:05 +02:00
Jouni Malinen
a826ff2d95 Ignore group-addressed SA Query frames
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-27 20:27:00 +02:00
Jouni Malinen
8f557d2047 Make wpa_bss_ext_capab() handle NULL bss argument
This simplifies the callers that use wpa_s->current_bss (which could be
NULL).

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-06 12:09:30 +02:00
Jouni Malinen
6ead8b897f Use bool for is_6ghz variables and functions
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-12-11 19:56:14 +02:00
Yegor Yefremov
b439b21a2f wpa_supplicant: Fix typos
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2020-10-20 00:37:01 +03:00
Veerendranath Jakkam
5ecb45a41c OCV: Use more granular error codes for OCI validation failures
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-09-11 15:23:28 +03:00
Veerendranath Jakkam
93a73ce028 MSCS: Fix issues due to incorrect usage of wpa_hexdump_buf()
Previously wpabuf_head() of the buffer is passed to wpa_hexdump_buf()
instead of the wpabuf struct itself and it was causing wpa_supplicant to
crash. Fix this by using the correct pointer in the debug prints.

Fixes: a118047245 ("MSCS: Add support to send MSCS Request frames")
Fixes: c504ff5398 ("MSCS: Add support to populate MSCS Descriptor IE in (Re)AssocReq")
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-09-08 19:38:35 +03:00
Vinita S. Maloo
d21dde9dac MSCS: Send MSCS change/remove frames only if MSCS setup exists
Allow MSCS change/remove request to be sent only after an initial setup,
i.e., after an add request has been accepted.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Vinita S. Maloo
c504ff5398 MSCS: Add support to populate MSCS Descriptor IE in (Re)AssocReq
Include the MSCS Descriptor IE in the (Re)Association Request frames to
setup MSCS between the AP and the STA during association.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Jouni Malinen
2a58968d39 SAE-PK: Allow SAE-PK password to be set using the psk parameter
Only the sae_password parameter was previously accepted for SAE-PK use.
That is not sufficient for covering mixed SAE+PSK cases. Extend this by
allowing the psk parameter to be used as well just like it can be used
for SAE without SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-07 00:49:00 +03:00
Jouni Malinen
9ad010c290 SAE-PK: Allow automatic SAE-PK to be disabled
This replaces the previously used sae_pk_only configuration parameter
with a more generic sae_pk that can be used to specify how SAE-PK is
negotiated. The default behavior (sae_pk=0) is to automatically
negotiate SAE-PK whenever the AP supports it and the password is in
appropriate format. sae_pk=1 allows only SAE-PK to be used and sae_pk=2
disables SAE-PK completely.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 11:55:16 +03:00
Jouni Malinen
cc22fb1b86 SAE: Move H2E and PK flags to main sae_data
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
1c846d647e SAE-PK: Allow SAE authentication without PK to be disabled
The new wpa_supplicant network profile parameter sae_pk_only=1 can now
be used to disable use of SAE authentication without SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
e7aeb6d8ac SAE-PK: STA functionality
This adds STA side functionality for SAE-PK. This version enables SAE-PK
automatically based on the configured SAE password value if the selected
AP advertises support for SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
6b9e99e571 SAE-PK: Extend SAE functionality for AP validation
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
8c1f61e820 OCV: Report OCI validation failures with OCV-FAILURE messages (STA)
Convert the previously used text log entries to use the more formal
OCV-FAILURE prefix and always send these as control interface events to
allow upper layers to get information about unexpected operating channel
mismatches.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-30 00:24:15 +03:00
Jouni Malinen
52579be860 OCV: Move "OCV failed" prefix to callers
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:34:59 +03:00
Vamsi Krishna
2d118f557a OCV: Add support to override channel info OCI element (STA)
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:01:44 +03:00
Jouni Malinen
12c8eacf73 DPP: Allow version number to be overridden for testing purposes
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:45 +03:00
Jouni Malinen
1f5f000086 DPP2: Try to negotiate PFS only if AP supports version 2 or newer
Check AP's DPP Protocol Version during network introduction and mark the
PMKSA cache as suitable for PFS use with version 2 or newer. This avoids
unnecessary attempt of negotiating PFS with version 1 APs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
f6c22dcdea Use a local pointer to simply current_ssid accesses in sme_associate()
It is simpler to assign wpa_s->current_ssid to a local pointer now that
there are numerous dereferences of current_ssid within sme_associate().

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
da8478a1ab EAPOL supp: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
P Praneesh
7c8f540ee0 wpa_supplicant: Add HE override support
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.

There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.

Signed-off-by: P Praneesh <ppranees@codeaurora.org>
2020-03-30 12:55:01 +03:00
Jouni Malinen
5058f771d9 DPP2: Allow station to require or not allow PFS
The new wpa_supplicant network profile parameter dpp_pfs can be used to
specify how PFS is applied to associations. The default behavior
(dpp_pfs=0) remains same as it was previously, i.e., try to use PFS if
the AP supports it. PFS use can now be required (dpp_pfs=1) or disabled
(dpp_pfs=2).

This is also working around an interoperability issue of DPP R2 STA with
certain hostapd builds that included both OWE and DPP functionality.
That issue was introduced by commit 09368515d1 ("OWE: Process
Diffie-Hellman Parameter element in AP mode") and removed by commit
16a4e931f0 ("OWE: Allow Diffie-Hellman Parameter element to be
included with DPP"). hostapd builds between those two commits would
reject DPP association attempt with PFS. The new wpa_supplicant default
(dpp_pfs=0) behavior is to automatically try to connect again with PFS
disabled if that happens.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 17:23:22 +02:00
Jouni Malinen
eb26a6997d Allow SA Query to be disabled for testing purposes
The new wpa_supplicant control interface SET parameter disable_sa_query
can now be used to disable SA Query on receiving unprotected
disconnection event.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-21 18:12:02 +02:00
Jouni Malinen
6140cca819 FT: Omit RSNXE from FT protocol Reassociation Request when needed
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Request frame so
that an AP not supporting RSNXE can still validate the FTE MIC
correctly.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-21 00:01:47 +02:00
Ananya Barat
2b9713d616 Fill the current opclass in (Re)AssocRequest depending on HT/VHT IEs
The previous implementation was assuming a fixed 20 MHz channel
bandwidth when determining which operating class value to indicate as
the Current Operating Class in the Supported Operating Classes element.
This is not accurate for many HT/VHT cases.

Fix this by determining the current operating class (i.e., the operating
class used for the requested association) based on the HT/VHT operation
elements from scan results.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-11 18:30:31 +02:00
Jouni Malinen
10223b501b SAE: Expose sae_write_commit() error cases to callers
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:59:42 +02:00
Ilan Peer
c4988e73c0 driver: Extend send_mlme() with wait option
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.

hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:03:20 +02:00
Jouni Malinen
200c7693c9 Make WEP functionality an optional build parameter
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 17:45:25 +02:00
Jouni Malinen
641d79f165 SAE: Special test mode sae_pwe=3 for looping with password identifier
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-10 05:13:13 +02:00
Jouni Malinen
ca1cecc54d SAE: Verify that appropriate Status Code is used in SAE commit (SME)
Previous version accepted both 0 and 126 values in SAE commit message
from the AP. Explicitly check that the value the AP uses matches what
the STA started with to avoid unexpected cases.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-08 07:19:53 +02:00
Vamsi Krishna
d0e116f61f Enhance get_mode() to return correct hw_mode with 6 GHz support
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to be stored
in a separate hw_features set (but with same mode
HOSTAPD_MODE_IEEE80211A) due to possibility of different HT/VHT/HE
capabilities being available between the 5 GHz and 6 GHz bands.

Iterate through all hw_features sets and check and match the band of
channel supported by the hw_features set while getting the hw_features
set in get_mode(). This allows both the 5 GHz and 6 GHz channels to be
found and correct capabilities to be used in cases where the driver
reports different capability values between 5 and 6 GHz channels.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-23 15:48:51 +02:00
Jouni Malinen
5e32fb0170 SAE: Use Anti-Clogging Token Container element with H2E
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
e36a5894d0 SAE: Use H2E whenever Password Identifier is used
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
af670cb418 SME: Postpone current BSSID clearing until IEs are prepared
sme_send_authentication() could fail before actually requesting the
driver to authenticate with a new AP. This could happen after
wpa_s->bssid got cleared even though in such a case, the old association
is maintained and still valid. This can result in unexpected behavior
since wpa_s->bssid would not match the current BSSID anymore.

Fix this by postponing clearing of wpa_s->bssid until the IE preparation
has been completed successfully.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 18:06:01 +02:00
Sergey Matyukevich
3204795d7a STA OBSS: Add check for overlapping BSSs
In the previous implementation connected STA performs OBSS scan
according to requests from its 20/40 MHz AP. However STA checks only 40
MHz intolerance subfield from HT Capabilities element in scan results.
Meanwhile, as per IEEE Std 802.11-2016, 11.16.12, STA should check
overlapping BSSs as well.

Note that all the required code to check overlapping BSSs did already
exist for AP mode since AP does those checks properly before operating
as 20/40 MHz BSS in the 2.4 GHz band. Use that existing code by replace
existing 40 MHz intolerance check in sme_proc_obss_scan() with the new
shared helper function check_bss_coex_40mhz().

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2019-12-26 11:41:01 +02:00
Jouni Malinen
1325655397 SAE H2E: RSNXE override for testing purposes
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 12:54:54 +02:00
Jouni Malinen
c88e01e1b6 SAE H2E: Fix validation of rejected groups list
check_sae_rejected_groups() returns 1, not -1, in case an enabled group
is rejected. The previous check for < 0 could not have ever triggered.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 00:28:13 +02:00
Jouni Malinen
1b5865a53f SAE: Ignore commit message when waiting for confirm in STA mode
Previously, an unexpected SAE commit message resulted in forcing
disconnection. While that allowed recovery by starting from scratch,
this is not really necessary. Ignore such unexpected SAE commit message
instead and allow SAE confirm message to be processed after this. This
is somewhat more robust way of handling the cases where SAE commit
message might be retransmitted either in STA->AP or AP->STA direction.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-10-27 14:35:04 +02:00
Jouni Malinen
6d6c887751 SAE: Add RSNXE in Association Request and EAPOL-Key msg 2/4
Add the new RSNXE into (Re)Association Request frames and EAPOL-Key msg
2/4 when using SAE with hash-to-element mechanism enabled. This allows
the AP to verify that there was no downgrade attack when both PWE
derivation mechanisms are enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-17 16:54:05 +03:00
Jouni Malinen
444d76f74f SAE: Check that peer's rejected groups are not enabled
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
cfe1ea5c9c SAE: H2E version of SAE commit message handling for STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
447cd5f2df SAE: Collect list of rejected groups for H2E in STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
86f6084862 SAE: Tell sae_parse_commit() whether H2E is used
This will be needed to help parsing the received SAE commit.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-14 19:38:41 +03:00
Vamsi Krishna
2e06cef80a MBO/OCE: Work around misbehaving MBO/OCE APs that use RSN without PMF
The MBO and OCE specification require the station to mandate use of PMF
when connecting to an MBO/OCE AP that uses WPA2. The earlier
implementation prevented such misbehaving APs from being selected for
connection completely. This looks like the safest approach to take, but
unfortunately, there are deployed APs that are not compliant with the
MBO/OCE requirements and this strict interpretation of the station
requirements results in interoperability issues by preventing the
association completely.

Relax the approach by allowing noncompliant MBO/OCE APs to be selected
for RSN connection without PMF to avoid the main impact of this
interoperability issue. However, disable MBO/OCE functionality when PMF
cannot be negotiated to try to be as compliant as practical with the
MBO/OCE tech spec requirements (i.e., stop being an MBO/OCE STA for the
duration of such workaround association). Also disable support for BTM
in this workaround state since MBO would expect all BTM frames to be
protected.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-21 00:58:33 +03:00
Jouni Malinen
7d2ed8bae8 Remove CONFIG_IEEE80211W build parameter
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-09-08 17:33:40 +03:00
Sunil Dutt
346d10cf82 SAE: Conditionally set PMKID while notifying the external auth status
This is needed for the drivers implementing SME to include the PMKID in
the Association Request frame directly following SAE authentication.

This commit extends the commit d2b2083843 ("SAE: Allow PMKID to be
added into Association Request frame following SAE") for drivers with
internal SME that use the external authentication mechanism.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-16 15:37:36 +03:00
Sunil Dutt
b7cd64876d SAE: Use BSSID stored in ext_auth_bssid for set_pmk
pending_bssid is cleared in the connected state and thus is not valid if
SAE authentication is done to a new BSSID when in the connected state.
Hence use the BSSID from ext_auth_bssid while configuring the PMK for
the external authentication case. This is required for roaming to a new
BSSID with driver-based-SME while the SAE processing happens with
wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-16 15:32:55 +03:00
Jouni Malinen
d2b2083843 SAE: Allow PMKID to be added into Association Request frame following SAE
IEEE Std 802.11-2016 does not require this behavior from a SAE STA, but
it is not disallowed either, so it is useful to have an option to
identify the derived PMKSA in the immediately following Association
Request frames. This is disabled by default (i.e., no change to previous
behavior) and can be enabled with a global wpa_supplicant configuration
parameter sae_pmkid_in_assoc=1.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-14 17:49:23 +03:00
Sven Eckelmann
f74618cb92 wpa_supplicant: Fix type for ssid->mode comparisons
The ssid->mode is from type enum wpas_mode and all its constants start
with WPAS_MODE_*. Still some of the code sections used the
IEEE80211_MODE_* defines instead of WPAS_MODE_*.

This should have no impact on the actual code because the constants for
INFRA, IBSS, AP and MESH had the same values.

Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
2019-06-23 18:03:51 +03:00
Srinivas Dasari
fb6ebd1ced SAE: Send external auth failure status to driver
wpa_supplicant prepares auth commit request as part of the external
authentication (first SAE authentication frame), but it fails to get
prepared when wpa_supplicant is started without mentioning the SAE
password in configuration. Send this failure status to the driver to
make it aware that the external authentication has been aborted by
wpa_supplicant.

Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
2019-05-31 16:52:15 +03:00
Jouni Malinen
d42df8d6ce Fix a regression in storing of external_auth SSID/BSSID
An earlier change in drivers_ops API for struct external_auth broke the
way SSID and BSSID for an external authentication request were stored.
The implementation depended on the memory array being available in the
API struct with a use of memcpy() to copy the full structure even though
when only SSID and BSSID was needed. Fix this by replacing that
easy-to-break storing mechanism with explicit arrays for the exact set
of needed information.

Fixes: dd1a8cef4c ("Remove unnecessary copying of SSID and BSSID for external_auth")
Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-28 16:24:32 +03:00
Andrei Otcheretianski
31cf52bf2e Do not clear FT IEs twice in sme_deinit()
Remove FT IEs clearing from sme_deinit() as it is done twice. The
sme_clear_on_disassoc() call to sme_update_ft_ies() takes care of this.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-04-16 00:48:27 +03:00
Andrei Otcheretianski
01ac337b32 Stop SA Query on disconnection
SA Query wasn't stopped after disconnection, which could potentially
result in an unexpected SA timeout firing later when already connected
to another AP. Fix that by stopping SA Query when an association is
terminated.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-04-16 00:48:27 +03:00
Jouni Malinen
7a206c504f Add debug print on stopping SA Query procedure
This makes it easier to debug SA Query behavior.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-16 00:42:58 +03:00
Jouni Malinen
dd1a8cef4c Remove unnecessary copying of SSID and BSSID for external_auth
The external authentication command and event does not need to copy the
BSSID/SSID values into struct external_auth since those values are used
before returning from the call. Simplify this by using const u8 * to
external data instead of the array with a copy of the external data.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-04-12 20:43:26 +03:00
Jouni Malinen
be609c6fc6 SAE: Fix commit message override with external authentication
Do not add duplicate Transaction Sequence and Status Code fields when
using test functionality to override SAE commit message.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-04-01 13:28:26 +03:00
Jouni Malinen
ab3aebcce5 SAE: Fix PMKSA cache entry search for FT-SAE case
Previously, PMKSA cache entries were search for AKM=SAE and that did not
find an entry that was created with FT-SAE when trying to use FT-SAE
again. That resulted in having to use full SAE authentication instead of
the faster PMKSA caching alternative.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-27 04:03:12 +02:00
vamsi krishna
bcf1900058 FT-SAE: Enable external auth support for FT-SAE also
Extend the external authentication support to FT-SAE mode connections
also in addition to SAE mode connections.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-27 03:18:13 +02:00
Jouni Malinen
322d328e71 FT: Fix SAE + FT-SAE behavior in association parameter selection
Do not try to initialize FT reassociation if the selected AKM is for SAE
instead of FT-SAE when both of these are enabled in a network profile.
This fixes an issue with MDE being included in an (Re)Association
Request frame even when using a non-FT AKM (which is something that
results in hostapd rejecting the association).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-26 22:50:17 +02:00
Jouni Malinen
10ec6a5f38 DPP2: PFS for PTK derivation
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-18 18:32:31 +02:00
Jouni Malinen
dd6c598007 DPP: Support DPP and SAE in the same network profile
Make both DPP and SAE code aware of the cases where the same network
profile is configured to enable both DPP and SAE. Prefer DPP over SAE in
such cases and start DPP/SAE exchanges based on what both the station
and the AP support.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-16 17:29:59 +02:00
Jouni Malinen
fd83089120 SAE: Reuse previously generated PWE on a retry with the same AP
Do not start SAE authentication from scratch when the AP requests
anti-clogging token to be used. Instead, use the previously generated
PWE as-is if the retry is for the same AP and the same group. This saves
unnecessary processing on the station side in case the AP is under heavy
SAE authentiation load.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-06 13:07:11 +02:00
Jouni Malinen
a9fe13035e SAE: Enable only groups 19, 20, and 21 in station mode
Remove groups 25 (192-bit Random ECP Group) and 26 (224-bit Random ECP
Group) from the default SAE groups in station mode since those groups
are not as strong as the mandatory group 19 (NIST P-256).

In addition, add a warning about MODP groups 1, 2, 5, 22, 23, and 24
based on "MUST NOT" or "SHOULD NOT" categorization in RFC 8247. All the
MODP groups were already disabled by default and would have needed
explicit configuration to be allowed.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-05 17:23:58 +02:00
Ben Greear
cb828507f5 Use disable_ht/vht to constrain supported operating class information
If user has disabled HT or VHT, those related operating classes
should not be advertised as supported.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2019-01-08 00:19:07 +02:00
Jouni Malinen
f808bd59e8 FT: Do not try to use FT-over-air if reassociation cannot be used
There is no point in going through FT authentication if the next step
would have to use association exchange which will be rejected by the AP
for FT, so only allow FT-over-air if previous BSSID is set, i.e., if
reassociation can be used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-04 23:22:46 +02:00
Venkateswara Naralasetty
5abc7823bd wpa_supplicant: Add Multi-AP backhaul STA support
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.

This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.

Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2018-12-20 12:10:31 +02:00
Mathy Vanhoef
f91e68e903 OCV: Perform an SA Query after a channel switch
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
f9da7505bf OCV: Include and verify OCI in SA Query frames
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.

On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.

Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.

As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:42:23 +02:00
Jouni Malinen
ec2cf403b8 HS 2.0: As a STA, do not indicate release number greater than the AP
Hotspot 2.0 tech spec mandates mobile device to not indicate a release
number that is greater than the release number advertised by the AP. Add
this constraint to the HS 2.0 Indication element when adding this into
(Re)Association Request frame. The element in the Probe Request frame
continues to show the station's latest supported release number.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-08 14:06:58 +02:00
Jouni Malinen
f2973fa39d FT: Fix CONFIG_IEEE80211X=y build without CONFIG_FILS=y
remove_ie() was defined within an ifdef CONFIG_FILS block while it is
now needed even without CONFIG_FILS=y. Remove the CONFIG_FILS condition
there.

Fixes 8c41734e5d ("FT: Fix Reassociation Request IEs during FT protocol")
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-03 12:00:26 +02:00
Ashok Kumar
698c9e2021 OWE: Try another group only on association rejection with status 77
Do not change the OWE group if association is rejected for any other
reason than WLAN_STATUS_FINITE_CYCLIC_GROUP_NOT_SUPPORTED to avoid
unnecessary latency in cases where the APs reject association, e.g., for
load balancing reasons.

Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
2018-12-02 20:42:09 +02:00
Jouni Malinen
8c41734e5d FT: Fix Reassociation Request IEs during FT protocol
The previous implementation ended up replacing all pending IEs prepared
for Association Request frame with the FT specific IEs (RSNE, MDE, FTE)
when going through FT protocol reassociation with the wpa_supplicant
SME. This resulted in dropping all other IEs that might have been
prepared for the association (e.g., Extended Capabilities, RM Enabled
Capabilities, Supported Operating Classes, vendor specific additions).

Fix this by replacing only the known FT specific IEs with the
appropriate values for FT protocol while maintaining other already
prepared elements.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-01 22:02:55 +02:00
Jouni Malinen
3d1d469195 Fix indentation level
This gets rid of smatch warnings about inconsistent indenting.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-11-30 21:28:19 +02:00
Ashok Ponnaiah
fcb3f11e4d SAE: Fix external authentication on big endian platforms
Need to handle the little endian 16-bit fields properly when building
and parsing Authentication frames.

Fixes: 5ff39c1380 ("SAE: Support external authentication offload for driver-SME cases")
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-11-30 17:26:26 +02:00
Cedric Izoard
18a0508a41 external-auth: Check key_mgmt when selecting SSID
When selecting SSID to start external authentication procedure also
check the key_mgmt field as several network configuration may be defined
for the same SSID/BSSID pair. The external authentication mechanism is
only available for SAE.

Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
2018-11-26 19:09:25 +02:00
Jouni Malinen
dc673aec46 HS 2.0: Generate AssocReq OSEN IE based on AP advertisement
Parse the OSEN IE from the AP to determine values used in the AssocReq
instead of using hardcoded cipher suites. This is needed to be able to
set the group cipher based on AP advertisement now that two possible
options exists for this (GTK_NOT_USED in separate OSEN BSS; CCMP or
GTK_NOT_USED in shared BSS case). Furthermore, this is a step towards
allowing other ciphers than CCMP to be used with OSEN.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-11-09 18:07:16 +02:00
Ilan Peer
170244a1cd SME: Fix order of WPA IE in association request
In case that the protocol used for association is WPA the WPA IE was
inserted before other (non vendor specific) IEs. This is not in
accordance to the standard that states that vendor IEs should be placed
after all the non vendor IEs are placed. In addition, this would cause
the low layers to fail to properly order information elements.

To fix this, if the protocol used is WPA, store the WPA IE and reinsert
it after all the non vendor specific IEs were placed.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2018-10-20 11:26:13 +03:00
Beni Lev
077232f603 OCE: Add OCE capability attribute only when associating to an OCE AP
Signed-off-by: Beni Lev <beni.lev@intel.com>
2018-09-02 18:16:30 +03:00
Ankita Bajaj
af835d75b7 FILS: Fix FILS connect failures after ERP key invalidation
If the RADIUS authentication server dropped the cached ERP keys for any
reason, FILS authentication attempts with ERP fails and the previous
wpa_supplicant implementation ended up trying to use the same keys for
all consecutive attempts as well. This did not allow recovery from state
mismatch between the ERP server and peer using full EAP authentication.

Address this by trying to use full (non-FILS) authentication when trying
to connect to an AP using the same ERP realm with FILS-enabled network
profile if the previous authentication attempt had failed. This allows
new ERP keys to be established and FILS authentication to be used again
for the consecutive connections.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-08-24 16:27:34 +03:00
Jouni Malinen
9be19d0b9c SAE: Add support for using the optional Password Identifier
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-05-19 17:30:29 +03:00
Ahmad Masri
60a5737e8f FT: Clear SME FT data on disassoc
SME ft_used flag is sometimes not cleared on disassoc. For example,
after initial FT connection, ft_used is set while ft_ies stays NULL.
Later on, upon disassoc, sme_update_ft_ies() is not invoked and ft_used
is not cleared. Fix this by invoking sme_update_ft_ies() also in case
ft_used is set.

This is needed to fix an issue with drivers that use nl80211 Connect API
with FT and expect to the NL80211_AUTHTYPE_OPEN specified in the Connect
command for the initial mobility domain association.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2018-05-04 20:56:52 +03:00
Jouni Malinen
4204669c69 HS 2.0: Add Roaming Consortium Selection element into AssocReq
This makes wpa_supplicant add Hotspot 2.0 Roaming Consortium Selection
element into (Re)Association Request frames if the network profile
includes roaming_consortium_selection parameter.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-18 01:12:25 +03:00
Jouni Malinen
852b2f2738 SAE: Only allow SAE AKMP for PMKSA caching attempts
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 19:34:44 +03:00
Jouni Malinen
06b1a10434 SAE: Fix default PMK configuration for PMKSA caching case
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 13:10:08 +03:00
Sunil Dutt
5ff39c1380 SAE: Support external authentication offload for driver-SME cases
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-02 21:17:55 +02:00
Jouni Malinen
2cb40e9f40 OWE: Try all supported DH groups automatically on STA
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 21:06:02 +02:00
Jouni Malinen
daa4096084 Allow last (Re)Association Request frame to be replayed for testing
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
a34ca59e4d SAE: Allow SAE password to be configured separately (STA)
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:24:19 +03:00
Jouni Malinen
265bda3444 OWE: Allow DH Parameters element to be overridden for testing purposes
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 18:26:29 +03:00
Jouni Malinen
ec9f483774 OWE: Support DH groups 20 (NIST P-384) and 21 (NIST P-521) in station
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
61a56c1480 Add group_mgmt network parameter for PMF cipher selection
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-26 17:40:02 +03:00