Commit graph

96 commits

Author SHA1 Message Date
Peng Xu
5f0bca77a8 Retry initial 20/40 MHz co-ex scan if the driver is busy
This makes the initial OBSS scans in AP mode before starting 40 MHz BSS
more robust. In addition, HT20 can be used as a backup option if none of
the scans succeed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-29 12:52:09 +03:00
Peng Xu
9c47f6a2a6 hostapd: Extend support for HT 20/40 coexistence feature
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.

If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-29 12:52:09 +03:00
Jouni Malinen
5583b8d1eb Document and rename HT Capability/Operation fields
This makes the definitions match the terminology used in IEEE Std
802.11-2012 and makes it easier to understand how the HT Operation
element subfields are used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 22:45:11 +03:00
Jouni Malinen
1dde5b5cdd Remove PSMP option from ht_capab
This was used to fill in the "PSMP support" subfield that was defined
during P802.11n development. However, this subfield was marked reserved
in the published IEEE Std 802.11n-2009 and it is not supported by
current drivers that use hostapd for SME either. As such, there is not
much point in maintaining this field as ht_capab parameter within
hostapd either.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 22:02:14 +03:00
Amar Singhal
70634eec0c hostapd: Check driver DFS offload capability for channel disablement
If the driver supports full offloading of DFS operations, do not disable
a channel marked for radar detection. The driver will handle the needed
operations for such channels.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-22 21:31:15 +02:00
Jouni Malinen
49b74430d9 Fix HT40 co-ex scan for some pri/sec channel switches
Secondary channel was compared incorrectly (-4/4 vs. actual channel
number) which broke matching neighboring 40 MHz BSSes and only the
no-beacons-on-secondary-channel rule was applied in practice. Once
sec_chan was fixed, this triggered another issue in this function where
both rules to switch pri/sec channels could end up getting applied in a
way that effectively canceled the switch.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 19:04:31 +02:00
Bartosz Markowski
905828fea4 hostapd: Fix vht_capab 'Maximum A-MPDU Length Exponent' handling
As per IEEE Std 802.11ac-2013, 'Maximum A-MPDU Length Exponent' field
value is in the range of 0 to 7. Previous implementation assumed EXP0 to
be the maximum length (bits 23, 24 and 25 set) what is incorrect.

This patch adds options to set it up within the 0 to 7 range.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
2014-03-06 00:09:37 +02:00
Jouni Malinen
ca412c7a38 Remove unreachable return statement
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-02 10:35:33 +02:00
Jouni Malinen
c1151e47d5 Force OFDM/HT/VHT to be disabled on channel 14
The regulatory rules in Japan do not allow OFDM to be used on channel
14. While this was to some extend assumed to be enforced by drivers
(many of which apparently don't), it is safer to make hostapd enforce
this by disabling any OFDM-related functionality. This tries to avoid
backwards compatibility issues by downgrading the mode rather than
rejecting the invalid configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-25 13:55:10 +02:00
Jouni Malinen
5f9c134ab4 Remove obsolete license notifications
These files have been distributed only under the BSD license option
since February 2012. Clarify the license statements in the files to
match that to avoid confusion.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 22:59:52 +02:00
Andrei Otcheretianski
13daed58c7 Include driver.h in hostapd.h
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-12-24 08:22:37 +02:00
Jouni Malinen
afadaff976 Optimize 40 MHz HT co-ex scan on AP
Only scan the affected channels instead of all enabled channels when
determining whether the primary and secondary channel for HT40 needs to
be swapped. This speed up HT40 setup considerably on 5 GHz band.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
e1c5faf007 hostapd: Track interface state
The new hostapd_iface::state enum is used to track the current state of
the hostapd interface (a radio/wiphy).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
ae134e1d2b hostapd: Add ctrl_iface events for ACS
These give status information to external observers from automatic
channel selection operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Eliad Peller
c781eb8428 hostapd: Verify VHT capabilities are supported by driver
Make sure the defined VHT capabilities are supported by the driver.

Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
2013-10-27 19:11:29 +02:00
Jouni Malinen
e7ecab4a3b Use ARRAY_SIZE() macro
Replace the common sizeof(a)/sizeof(a[0]) constructions with a more
readable version.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 17:49:05 +03:00
Helmut Schaa
3645fd5aae hostapd: Propagate ACS errors to iface setup
Otherwise hostapd might hang doing nothing anymore. Propagate ACS
errors so we can fail gracefully.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:36 +03:00
Helmut Schaa
0e1d0b370f hostapd: Don't get stuck after failed ACS
If ACS fails we still need to call hostapd_setup_interface_complete.
Otherwise hostapd will just hang doing nothing anymore. However, pass
an error to hostapd_setup_interface_complete to allow a graceful fail.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:30 +03:00
Janusz Dziedzic
58b73e3dd9 hostapd: DFS with 40/80 MHz channel width support
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-17 21:05:44 +03:00
Janusz Dziedzic
e76da50529 hostapd: Add AP DFS support
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.

This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.

Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>

Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-17 21:05:15 +03:00
Michal Kazior
50f4f2a066 hostapd: Add Automatic Channel Selection (ACS) support
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.

To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.

For more details see wiki page [1] or comments in src/ap/acs.c.

[1]: http://wireless.kernel.org/en/users/Documentation/acs

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-08-31 11:51:06 +03:00
Michal Kazior
245e026ec8 hostapd: Split up channel checking into helpers
This splits up the channel checking upon initialization into a few
helpers. This should make this a bit easier to follow. This also paves
the way for some initial ACS entry code.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-08-25 18:35:20 +03:00
Johannes Berg
3aea5fbe3b hostapd: Do not change HT40 capability due to OBSS scan
The capability itself isn't really affected by an OBSS
scan, only the HT operation must then be restricted to
20 MHz. Change this, and therefore use the secondary
channel configuration to determine the setting of the
OP_MODE_20MHZ_HT_STA_ASSOCED flag.

This shouldn't really change anything functionally,
it just makes the code a little less confusing and
is also needed to implement more dynamic bandwidth
changes if ever desired.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-02-09 12:16:58 +02:00
Vladimir Kondratiev
7829894c21 Introduce 60 GHz band
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:

network={
        ssid="test"
        mode=2
        frequency=60480
        key_mgmt=NONE
}

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-18 11:50:35 +02:00
Jouni Malinen
f0898e9519 Make copies basic_rates list more useful
Commit e5693c4775 added a copy of the
determined basic rate set into struct hostapd_iface, but did not
actually copy the terminating -1 value. This could be problematic if
something were to actually try to use this list since would be no way to
know what is the last entry in the list. Fix this by copying the
terminating value.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-07 00:15:53 +03:00
Jouni Malinen
f9884c096a Convert os_zalloc() for an array to use os_calloc()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 20:44:21 +03:00
Jouni Malinen
7fa56233ae Scan only affected frequencies for 20/40 MHz co-ex check for
When starting an AP with HT40 on 2.4 GHz, limit the set of channels
to scan for based on the affected frequency range to speed up the
AP setup.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 12:12:32 +03:00
Ben Greear
af22a9994b Tell user why a channel cannot be used in AP mode
Signed-off-by: Ben Greear <greearb@candelatech.com>
2011-12-10 16:18:50 +02:00
Jouni Malinen
78018ae91d Fix basic_rates copying
Commit e5693c4775 used incorrect
sizeof to copy the basic rates.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 13:12:30 +02:00
Jouni Malinen
34445d12ee Convert hostapd_prepare_rates() to use struct hostapd_iface
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 12:20:17 +02:00
Jouni Malinen
e5693c4775 Merge set_rate_sets() driver_ops into set_ap()
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 12:16:03 +02:00
Jouni Malinen
5f17b3ee9f Remove unused parameters from set_rate_sets()
Only setting of the basic rate set was supported, so remove the
unused parameters.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 11:57:13 +02:00
Jouni Malinen
9e0e6902a2 Share a single wpa_scan_results_free() implementation
There is not really a very good location for this anywhere, but the
function is small enough to live as an inline function for now.
2011-10-22 22:09:40 +03:00
Jouni Malinen
93ac240496 Clarify hostapd error message on unsupported hw_mode value 2011-07-31 00:51:34 +03:00
Ben Greear
60eda5e47d Better messages when channel cannot be used in AP mode
Log messages letting user know that the channel cannot
be used because it is flagged unusable.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2011-05-16 22:01:11 +03:00
Sujith Manoharan
ec2b890981 HT: Skip ht_capab validation if ieee80211n=0
There is no point in running through the 40 MHz scan if HT is
actually disabled regardless of whether the ht_capab parameter
is set.
2011-03-16 11:22:40 +02:00
Jouni Malinen
2944824315 hostapd: Add require_ht configuration parameter
This can be used to configure hostapd to reject association with
any station that does not support HT PHY.
2011-02-09 15:08:47 +02:00
Jouni Malinen
7615078caf AP: Make sure ieee80211n_allowed_ht40_channel_pair() gets called
We need to call this function after having completed the neighboring
channel scan to figure out whether HT40 can be used and if so, which
channel is the secondary channel.
2011-02-01 16:09:26 +02:00
Nishant Sarmukadam
1b4d379366 AP: Ensure ieee80211n_supported_ht_capab() gets called to check ht caps
ieee80211n_supported_ht_capab is called after ieee80211n_check_40mhz in
function hostapd_check_ht_capab. ieee80211n_check_40mhz can return 1 in
a valid scenario where the initialization is completed in a callback. In
this case ieee80211n_supported_ht_capab is skipped and hostapd does not
check the ht capabilities reported by the driver. Fix this issue making
sure ieee80211n_supported_ht_capab gets called.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
2011-02-01 16:04:59 +02:00
Jouni Malinen
8ea3dd21d2 AP: Verify that HT40 secondary channel is supported
Refuse to enable HT40 mode AP unless both the primary and secondary
channels are enabled for AP use.
2010-11-12 18:31:56 +02:00
Felix Fietkau
5a5009dc92 Fix rate table handling
With the nl80211 driver, the rate table is mode dependent, so it
must be initialized after the hardware mode has been selected.
2010-11-09 16:17:50 +02:00
Jouni Malinen
416192628d Fix AP mode 40 MHz pri/sec channel parsing in overlap determination
The previous implementation ended up incorrectly assuming that all
40 MHz use cases have secondary channel above the primary one. Fix this
by properly masking the secondary channel offset field and checking its
value.
2010-10-06 14:09:44 +03:00
Jouni Malinen
d1f9c410c1 Remove src/drivers/scan_helpers.c
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
2010-01-03 20:27:32 +02:00
Jouni Malinen
6e6e8c31ff Replace src/ap/driver_i.h with non-inlined functions in ap_drv_ops.c 2009-12-26 00:21:22 +02:00
Jouni Malinen
6226e38d00 Rename some src/ap files to avoid duplicate file names
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
2009-12-26 00:05:40 +02:00
Jouni Malinen
70db2ab308 Move rest of the generic AP mode functionality into src/ap 2009-12-25 20:06:07 +02:00
Renamed from hostapd/hw_features.c (Browse further)