One TDLS test case was using wlantest without doing the setup first.
This makes the test not work on real hardware. Fix the issue by adding
the wlantest setup to the test.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Some TDLS and WPS test cases reference the hapd variable in the finally
block even if the test failed before assigning the value to this
variable. This makes the code in the finally block to fail on
referencing this variable. Assign None to the hapd variable before
starting the tests to avoid this.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use a monitor interface given in the command line that is not also a
station or an AP as a monitor running wlantest on the channel used by
the test. This makes all the tests that use wlantest available for
execution on real hardware on remote hosts.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (5) converts the cases that use the start_ap_wpa2_psk() helper
function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This adds more coverage for TDLS testing for a case where the direct
link should use various VHT channel bandwidths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify correct behavior with invalid commands. In addition, allow minor
mac80211_hwsim modifications to be used to enable testing of the driver
interface to enable and disable channel switching.
Signed-off-by: Jouni Malinen <j@w1.fi>
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit bf700cc3d2. The
concurrent initialization test case is now expected to work again with
the STA entry added early enough to avoid the recently added mac80211
validation step failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Older mac80211 implementations did not set the link identifier
appropriately, resulting in an incorrect teardown packet being sent the
peer. wpa_supplicant adds the FTE containing the MIC field calculated
using the correct link-identifier. This causes a MIC failure on the
other side and the teardown is discarded. Verify this case is fixed by
newer kernel and wpa_supplicant code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
A mac80211 TDLS validation change ended up breaking test functionality
that was needed for this test case. Instead of reporting this known
issue as a FAIL every time, mark the test as SKIP since the issues is
known and there are no plans of "fixing" it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
A full scan in these specific test cases does not add anything to the
coverage, so use a single channel scan for the station connection to
remove undesired extra time needed for a full scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make sure the connection between each STA and the AP is in working state
between each TDLS setup/teardown operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
