This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.
Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Process Authentication Confirm with the two failure cases defined in the
spec: STATUS_NOT_COMPATIBLE and STATUS_AUTH_FAILURE. This verifies the
{R-nonce}k2 part and reports more detailed failure reason if the message
is valid.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If Authentication Response processing fails due to R-capab
incompatibility or R-auth mismatch, send Authentication Confirm with
error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow I-nonce, R-capab, R-auth,
and I-auth values in Authentication Response/Confirm to use incorrect
values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, Initiator decided whether to use mutual authentication on
its own based on having own and peer bootstrapping info. This prevented
Responder from selecting not to use mutual authentication in such a
case. Fix this by allowed Initiator to fall back to non-mutual
authentication based on Responder choice if the bootstrapping mechanism
allows this (PKEX does not; it mandates use of mutual authentication).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Confirm to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Response to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up old dpp_auth_build_resp() (now dpp_auth_build_resp_ok())
a bit by separating initialization steps for a DPP authentication
session from the code needed to build the frame. This allows
dpp_auth_build_resp_status() to share the helper function instead of
having to maintain a duplicated message construction implementation. In
addition, this makes it easier to remove some of the attributes for
protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Request to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_auth_init() a bit by separating initialization steps
for a DPP authentication session from the code needed to build the
frame. In addition, this makes it easier to remove some of the
attributes for protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While using an external RADIUS server SUCCESS messages were not being
sent (internal was fine). Also add event messages for other states that
others might find useful, and consistency between the two.
Signed-off-by: Michael Baird <Michael.Baird@ecs.vuw.ac.nz>
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After an initial connection certain connection parameters may be
updated. It may be necessary to send these parameters to drivers since
these will be used in driver-initiated roaming cases. This commit
defines the driver_ops call for this and implements the needed
functionality for the nl80211 driver interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add additional attributes to specify the PMK, PMKID, and the ERP next
sequence number to the vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH. These are needed in case
of an offloaded FILS roaming.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a corner case where RSN pre-authentication candidate from
scan results was ignored if the station was associated with that BSS
just before running the new scan for the connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a more accurate scan result age to be fetched than the one
available through NL80211_BSS_SEEN_MS_AGO.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that TK, KCK, and KEK lengths are set to consistent values within
struct wpa_ptk before using them in supplicant. This is an additional
layer of protection against unexpected states.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of setting the default PMK length for the cleared PMK, set the
length to 0 and explicitly check for this when deriving PTK to avoid
unexpected key derivation with an all-zeroes key should it be possible
to somehow trigger PTK derivation to happen before PMK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
