There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
The radio works for the interface get removed if interface is disabled.
This could have left P2P module in invalid state if the interface got
disabled during a p2p_find or p2p_listen operation. Clear the state in
such a case to avoid blocking following operations due to P2P module
assuming it is still in progress of doing something.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
No need to call ibss_rsn_deinit() again since it is already being called
by wpa_supplicant_mark_disassoc().
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an ANQP fetch is triggered and ANQP_3GPP_CELLULAR_NETWORK info is
required, initialize scard to be ready when comparing ANQP and
credentials.
Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 3d910ef497 tried to make
last-network selection behave more consistently with Interworking
network selection preferences. However, it did not take into account
that other network block may have higher priority. In such cases, the
last added network from Interworking network selection should actually
not be selected for the next connection. Fix this by limiting the
last-network preference to work only within a priority class.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it would have been possible for the network to be marked
disabled and that marking to be ignored if a recoverable disconnection
reason event were processed. Avoid this by verifying network status
before trying to reconenct back to the same BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpa_s->current_bss was updated too late for the
wpa_supplicant_rsn_supp_set_config() call within
wpa_supplicant_select_config(). Re-order code so that current_bss gets
updated between current_ssid update and this call to set the WPA state
machine configuration, so that the new code that determines whether the
current GO support the new IP address assignment mechanism works.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Conver Public Action
GAS queries to use Dual of Public Action frame if PMF has been
negotiated with the AP to which the frame is being sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scan request failures are observed in wpa_supplicant debug log when
Android framework starts PNO scan in driver via ctrl interface command
'set pno 1' and wpa_supplicant also tries to issue a scan request after
PNO has started in the driver.
Some drivers may reject a normal scan request when PNO is already in
progress. wpa_supplicant should consider PNO status before issuing start
scan request to the driver. Otherwise, wpa_supplicant will get failures
from driver for the scan request and it will end up rescheduling scan
request in periodic interval and get a start scan request failure for
each attempt.
In order to avoid unnecessary scan attempt when PNO scan is already
running, PNO status is checked before issuing scan request to driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch resets the static interface_count to zero in case of
wpa_supplicant_driver_init() call for wpa_s which is in
INTERFACE_DISABLED state. This interface_count is used for the delay of
the scan which is now minimal for dynamically added interfaces. This may
collide with a scan for another interface, but the same is true for any
chosen delay in this scenario. Also the state change to DISCONNECTED is
moved to wpa_supplicant_driver_init() so it will move from
INTERFACE_DISABLED to INACTIVE when there are no enabled networks.
Tested-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_s->scan_res_handler is set only for cases where a scan operation is
requested for a specific purpose. As such, this callback should only be
called when a scan result from a scan that was triggered by
wpa_supplicant is processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, the shorter scan interval was already in use for the
connection following the provisioning step, but same optimization can
also be used for the pre-provisioning scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It may not always be desirable to trigger reassociation or network
change based on scan results from externally to wpa_supplicant trigger
scan operations. Skip network selection and roaming determination if the
received scan result is known to be triggered by something external to
wpa_supplicant. The control interface SCAN command can be used to
request wpa_supplicant to determine the best network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
An INTERFACE_DISABLED event received on an interface that is
currently operating a P2P GO means that the group session ended.
In such a case, if the interface was dynamically added remove it, and
if not, remove all the network blocks that are temporary, assuming
that if needed a new session will be started by an external entity.
The use case was triggering rfkill (both SW and HW). This case popped up
as part of a testing cycle, where after a toggle in the rfkill state,
the result was that the interface was not deleted, but on the other hand
the wpa_supplicant did not configure the kernel to re-start the AP
functionality again.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).
If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.
This patch fixes this issue by restoring the previous scan_req value.
Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
The shorter 250 ms wait for the next scan request can be used also for
the case of persistent group re-invocation instead of just formation of
a new group. This speeds up the process and makes this more robust
especially in cases where the GO is using MCC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The QoS Map Set element was passed in full to the driver instead of just
the payload of the element. This resulted in the updated QoS Map being
rejected. Validate the element id/len and send only the payload to the
driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Request new scan only for the interface for which the original scan
request and results has come. Otherwise while sharing scan results along
with P2P interfaces, the new scan will be requested on P2P interfaces.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This is a better way of matching P2P groups based on the unique P2P
Device Address (e.g., from P2P Group ID) and SSID pair instead of using
the not necessarily unique P2P Interface Address.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_setup_channels function uses the per interface information
(wpa_s->hw.modes) for setting up the available channel list for P2P
operation, but if a separate P2P interface is used (e.g., p2p0 on
Android), the wpa_s instance for that interface may not get an updated
channel list. This can result in some operations, like "P2P_SET
disallow_freq", using old channel list information (e.g., world roaming
information with passive-scan/no-ibss flags) which was initialized
during the start-up. This could result in P2P functionality using
conflicting or obsolete channel information.
To resolve this issue, update channel list information on regulatory
change events to all of the virtual interfaces sharing the same phy for
which the event is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P-GROUP-STARTED event depends on having enough information about the
group available. To avoid incomplete information from being delivered to
upper layers, do not accept scan results without P2P IE (e.g., from a
non-P2P scan) for P2P client association process. This can be of use for
some join-a-group cases where non-P2P scans have generated the BSS entry
for the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now in case of deauthentication from GO, immediate group removal will
happen in GC only if the deauthentication packet has a valid IE. However,
the IE in deauthentication packet is mandated only for managed P2P group.
So in normal P2P group the group removal is delayed and will happen later
only in group idle timeout.
This fixes a regression from commit
d7df0fa727 that changed the previous check
for data->deauth_info != NULL to data->deauth_info->ie != NULL.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wpa_supplicant behavior in WEP configuration was to try to
mimic a device that is not aware of WPA/WPA2 and as such, it tried to
connect to a WPA/WPA2 AP with the assumption that the AP could be
providing support for both WEP and WPA/WPA2 stations in the same BSS.
Such APs could have been used during transition from WEP to more secure
options, but that type of deployment have not been used in large number
and are not really of much use anymore taken into account that more or
less all new devices support WPA/WPA2. That combined with the preference
to deprecate WEP justifies removing this use case and making WEP
networking matching more strict by using the knowledge of AP advertising
WPA/WPA2 as an indication of WEP not being supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To better support the IBSS/RSN mechanism, wpa_supplicant has to be able
to detect a possible peer reboot and in this case it should start a new
EAPOL handshake.
To perform such reboot detection wpa_supplicant has to perform an Open
Authentication by sending an Authentication frame and then replying to
it. IF an Authentication frame is received when the key have already
been exchanged, wpa_supplicant understands that the peer has rebooted
and can reset its state machine.
Whenever a new peer is added to the IBSS wpa_supplicant will start the
Open Authentication and only after having accomplished it will start the
key exchange. If the driver does not support Authentication frame
exchange initiated from user space, this step is skipped to maintain
previous behavior (just go through EAPOL-Key frame processing).
The Open Authentication was partly supported by the Linux kernel but now
wpa_supplicant can register for Authentication frames, handle it in
userspace and so avoid any possible race condition.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
Signed-hostap: Antonio Quartulli <antonio@open-mesh.com>
This allows wpa_supplicant to associate to an AP that has VHT BSS
membership selector set to indicate VHT support is required for the BSS.
Without the patch it was impossible to connect to, e.g., hostapd-based
AP that has require_vht=1. wpa_supplicant was complaining with:
hardware does not support required rate 63.0 Mbps
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
wpa_s->pending_bssid is all zeros during connection attempt when
driver-based BSS selection is used. Take this into account when
determining whether new scan results should trigger a connection based
on wpa_s->current_ssid, i.e., a connection attempt with the selected
network instead of selected BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not requesting the auto connect on
dissassociation event if we are already in disconnected state and would
not try to connect anyway.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The fast-connect optimization to skip a new scan did not update how the
RSN preauthentication callback is used. There is no point in trying to
add preauthentication candidates from cases where scan was skipped, so
skip this call, too, in such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Scan result events are shared between all virtual interfaces sharing the
same radio. However, some of the steps are not really appropriate on
virtual interfaces that did not issue the scan request. Fix this by
making these steps conditional on the scan results being processed on
the interface that requested them.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6a1ce39599 moved the bssid
variable declaration to be outside CONFIG_IEEE80211R block and
triggered a compiler warning about unused variable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
Usual manual scan request may cause reassociation due to several
reasons. New command is intended to perform pure scan without taking any
automatic action based on the results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
On the DMG (60 GHz) band, capability bits defined differently from
non-DMG ones. Adjust capability matching to cover both cases.
Also, for non-DMG bands, check ESS bit is set.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Addition of wpa_supplicant_fast_associate() made it unnecessary to call
wpas_select_network_from_last_scan() directly from other files.
Signed-hostap: Jouni Malinen <j@w1.fi>
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision. This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.
Signed-hostap: Paul Stewart <pstew@chromium.org>
The link was not disabled for the case of implicit trigger from the
driver unlike in the case of explicit trigger fromc ctrl_iface. Make the
tear down sequences match in these cases by adding the TDLS_DISABLE_LINK
tdls_oper to the driver when processing the TDLS_REQUEST_TEARDOWN event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The WNM-Sleep Mode handler took over WNM Action frame processing without
addressing the previously implemented WNM handler. Fix this by moving
the BSs Transition Management processing into wnm_sta.c to share a
single handler function for WNM Action frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.
Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.
This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prevents situations like the following where we roam to a
lesser quality BSS just because the signal level delta is over our
threshold.
wlan0: Considering within-ESS reassociation
wlan0: Current BSS: 00:24:6c:74:0a:40 level=-51
wlan0: Selected BSS: 00:24:6c:74:0a:e0 level=-64
wlan0: Request association: reassociate: 0 selected: 00:24:6c:74:0a:e0
bssid: 00:24:6c:74:0a:40 pending: 00:00:00:00:00:00 wpa_state: COMPLETED
Signed-hostap: Robert Shade <robert.shade@gmail.com>
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver indicates the association (or authentication) was
rejected, wpa_supplicant should handle this connection failure similarly
to other cases. Previously, this was only handled with drivers that use
wpa_supplicant SME.
In case of cfg80211-based drivers, a rejected association was actually
already handled since cfg80211 generates a deauthentication event after
indicating connection failure. However, rejected authentication resulted
in wpa_supplicant waiting for authentication timeout to expire which is
unnecessary long wait.
Fix this by calling wpas_connection_failed() to use the common mechanism
to reschedule a new connection attempt with the previously attempted
BSSID blacklisted.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add a function to filter out known cases of disconnection during 4-way
handshake that are caused by something else than mismatch in PSK. This
commit adds the case where the local end determines a mismatch in
WPA/RSN element between Beacon/Probe Response frames and EAPOL-Key msg
3/4.
This can avoid some potentially confusing "WPA: 4-Way Handshake failed -
pre-shared key may be incorrect" ctrl_iface messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If two P2P_FIND commands and a station mode SCAN command are issued in a
sequence with the second P2P_FIND and SCAN commands started before the
initial scan from the first P2P_FIND command has completed,
sta_scan_pending may be left set without an automatic way of getting it
cleared. This can get P2P search stuck if no further station mode scan
operations are run.
Fix this by clearing the sta_scan_pending flag whenever station mode scans
are stopped due to no enabled networks resulting in INACTIVE mode getting
entered. In addition, avoid setting sta_scan_pending flag when a special
scan_res_handler is set so that this does not get enabled on the P2P
Device interface during a P2P search operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a connection operation is started on an interface based on scan
results, other virtual interfaces should not be information about the
results to avoid potential concurrent operations during the association
steps. Since the sibling notification of scan results received was added
as an optimization, skipping it for this type of cases is the simplest
way of avoiding unnecessary concurrent operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes sure that the interrupted station mode scan can be completed
after the P2P operations have had their chance of using the radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the scan results from before ANQP fetch are fresh (less than five
seconds old), do not run a new scan when selecting the BSS after having
used Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.
Signed-hostap: Jouni Malinen <j@w1.fi>
The same information is available in the BSS table, so we can reduce the
need for using the raw scan results in wpa_supplicant_need_to_roam().
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This broke SME
disassoc-while-authenticating workaround for cfg80211. Fix this by
restoring wpa_s->current_ssid in case SME authentication is in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).
Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The variables used within the #ifndef block here needs to be defined in
the beginning of the function to avoid issues with some compilers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.
Signed-hostap: Jouni Malinen <j@w1.fi>
The os_memcmp of bssid and wpa_s->bssid cannot return 0 in this
code path since identical os_memcmp was already done above.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the normal flow for association:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return BSSID )-- device driver
However, a device driver could return EINVAL for get_bssid() because it
recognizes it has already been disconnected. When the wpa_supplicant
received EINVAL, the bssid field could be used uninitialized in the
following flow:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
device driver (receive deauth)
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return EINVAL )-- device driver
Prevent this by requiring the get_bssid() call to succeed when
processing association events.
When a special scan_res_handler is used the scan parameters may not have
been suitable for other purposes (e.g., during a p2p_find operation). As
such, do not indicate such scan results to other virtual interfaces
using the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
In the properties changed signal, added a new property
"DisconnectReason", which carries the IEEE 802.11 reason code of the
most recent disassociation or deauthentication event. The reason code is
negative if it is locally generated. The property is sent to the DBUS
immediately so as to prevent it from being coalesced with other
disconnect events.
Signed-off-by: Gary Morain <gmorain@chromium.org>
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.
Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.
Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
This avoids issues with some APs rejecting a reassociation if the
station is not currently associated as reported by Yossi Wortzel.
The change is based on a patch from Arik Nemtsov.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an empty IPv4 packet as the keep-alive packet for WNM BSS max idle
period mechanism. This is not really the best possible frame to use for
this, but for now, it can do until a more suitable frame is figured out
for this (e.g., special LLC header to indicate link test purposes).
Signed-hostap: Jouni Malinen <j@w1.fi>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Both EAP-AKA and EAP-AKA' use USIM. Without this change, use of real
USIM card for EAP-AKA' was not allowed to proceed, i.e., only the
software simulated USIM operations were supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.
Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make wpa_supplicant_event() more consistent by not checking
data in either location handling EVENT_RX_MGMT events. This event
is required to specify the data so this pointer cannot be NULL.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d43d37ff2 broke EVENT_RX_MGMT
processing in wpa_supplicant AP mode. ap_mgmt_rx() needs to be called
for Probe Request frames even if they get notified through the new
D-Bus signal mechanism.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit 6bf731e8ce broke handling of
EVENT_CHANNEL_LIST_CHANGED by introducing a cached copy of the driver
channel list that does not get updated even if driver changes its list.
Fix this by synchronizing the cacched wpa_s->hw.modes information
whenever EVENT_CHANNEL_LIST_CHANGED is processed. This fixes P2P channel
list updates based on regulatory domain hints that may trigger driver to
change its supported channel list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When wpa_supplicant disconnects, e.g., due to authentication timeout,
we need to go through the EVENT_DISASSOC/DEAUTH processing similarly
to the driver triggered cases to get correct events delivered to the
ctrl_iface. Fix this by calling wpa_supplicant_event() in these cases
and by filtering out the confusing CTRL-EVENT-DISCONNECTED event with
all zeros BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to disable wpa_supplicant controlled roaming. It should
be noted that the WPA_DRIVER_FLAGS_BSS_SELECTION capability is the
preferred way for this and CONFIG_NO_ROAMING should be obsoleted once
drivers support the new NL80211_ATTR_ROAM_SUPPORT capability
advertisement.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This makes WPA_INTERFACE_DISABLED more consistent in indicating that
wpa_supplicant cannot currently control the interface regardless of
whether the interface is disabled or completely removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This fixes a build regression from commit
cd2f4ddfb9 by moving
wpa_supplicant_assoc_update_ie() outside the no-scan-processing ifdef
block.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.
In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch fixes an issue with roaming for drivers that set
WPA_DRIVER_FLAGS_BSS_SELECTION (currently ath6kl). On moving to an AP
with a different BSSID, an EVENT_ASSOC is received and the subsequent
4-way handshake may fail because of a mismatch between the RSN IE in
message 3/4 and in Beacon/Probe Response. This happens only when the APs
use different RSN IE contents and ap_scan is set to 1, since
wpa_supplicant fails to update its cached IEs.
Initial association may fail, too, in case of multiple APs with
the same SSID, since BSSID selection is done by the driver and again
a mismatch could be seen.
Fix these two issues by clearing and updating the cached IEs on
receiving an Association event from the driver. Also, retrieve the
scan results when the new BSS information is not present locally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP disconnects us with a reason code that indicates that it has
dropped the association, but could allow us to connect again, try to
reconnect to the same BSS without going through the full scan. This can
save quite a bit of time in some common use cases, e.g., when inactivity
timeout is used on the AP (and especially, when waking up from suspend
which has likely triggered some timeout on the AP).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the MAC address of the interface to be changed when the
interface is set down even if the interface does not get completed
removed and re-added.
Signed-hostap: Jouni Malinen <j@w1.fi>
A disconnection event from the driver may end up getting delivered at a
time when wpa_supplicant is not even trying to connect (e.g., during a
scan that was already started after WPS provisioning step). In such a
case, there is not much point calling wpas_connection_failed() and
skipping this avoids confusing attempts of re-starting scanning while
the previous scan is still in progress.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_rsn_preauth_scan_results() needs to be called to
update RSN pre-authentication candidates. This cannot be done before
the wpa_supplicant_connect() call on the first association, but when
trying to figure out whether to roam, it is fine to do so for the
case when roaming is skipped.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
At least with driver_test.c, the BSS table may not include frequency
information. In such a case, we need to skip rate set matching during
BSS selection to avoid rejecting valid AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
Once PBC overlap detected when using dynamic group interfaces, the wpa_s
corresponding to P2P group interface is freed. This patch avoids
accessing the wpa_s data structure after it is freed. This fixes a
possible crash in P2P client role in such a case.
Disable the direct connection when a TDLS peer stops responding
to packets, as indicated by the "LOW ACK" event coming from a driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
When a driver does not implement the TDLS_TEARDOWN operation internally,
send an explicit TDLS link teardown frame to the driver.
Change all teardown calls to use these calling semantics.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Register for the TDLS discovery response public action frame in nl80211.
Print out a debug message when a Discovery Resp frame is received and
validated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
IEEE Std 802.11-2007 7.3.2.2 demands that in order to join a BSS all
required basic rates have to be supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
EVENT_WPS_BUTTON_PUSHED wpa_supplicant_event can now be used in
station mode driver_*.c to indicate that a push button has been
pushed. This will activate WPS PBC mode.
This patch uses sched_scan, if available, when the driver is
initialized. It also adds a couple of cancel operations where
appropriate.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
This allows the AP to be selected based on the BSSID when WPA-PSK
is used with a passphrase. The PSK will be derived from the passphrase
after the SSID has been learned from scan results.
This implements GAS request mechanism that is aimed at being used to
replace use case specific GAS/ANQP implementations in the future.
Compared to the earlier implementation in P2P SD, this implementation
includes support for multiple concurrent requests and more thorough
validation of frames against the pending query data.
GAS header processing, including comeback and reassembly, are handled
within gas_query.c and the users of this module will only need to
provide the Query Request and process the (possibly reassembled)
Query Response.
If the driver indicates that it supports BSS selection (including
roaming within an ESS) with WPA_DRIVER_FLAGS_BSS_SELECTION, modify
ap_scan=1 mode to behave like ap_scan=2 mode for BSS selection.
The initial scan is still done to avoid the need for strict
configuration of or security parameters (e.g., to figure out whether
TKIP or CCMP is being used as the group cipher). However, when
requesting the driver to connect, the bssid and freq parameters are
not provided to leave the driver in control of selecting which BSS
to use and to allow the driver to decide when to roam.
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous ft_ies needs to be removed before supplicant starts a new FT
initial association and this requires the ft_used state to be cleared
here.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Regardless of how the AP mode is disabled, wpa_supplicant_ap_deinit()
must be called. Make sure this happens on all paths by calling the
deinit function from wpa_supplicant_mark_disassoc().
These checks were previously skipped if the scan result included WPA
or RSN IE. However, that can result in selecting a network that does
not match local configuration in some cases.
Processing of the scan results for RSN pre-authentication candidates
was moved to happen before the network was selected. This resulted in
all candidates being dropped due to no SSID having been configured.
Fix this by moving the processing to happen after the network has
been selected. Since the raw scan results are not available at that
point, use the BSS table instead of scan results to fetch the
information.
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
It is now possible to configure the the time in seconds that
wpa_supplicant waits before requesting a new scan after failing to find
a suitable network in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If WPA/WPA2 was enabled in the configuration, the non-WPA exception
could allow an incorrect AP to be selected from scan results. Do
not use the exception if WPA/WPA2 is enabled in configuration.
Change the old design of running a single long living RSN IBSS
instance to keep a separate instance for each IBSS connection.
This fixes number of issues in getting keys set properly for
new connections and is in general quite a bit more correct
design.
Move the code snippet to switch on bgscan over to wpa_supplicant.c
from event.c, so that it can be activated on wpa_supplicant_set_state().
Also create a centralized place to switch off bgscan. bgscan is now
turned on in COMPLETED, not ASSOCIATED.
When wpa_s scans in AP mode, it doesn't propagate the scan event to the
AP code, so that code can get stuck if it uses the callbacks there.
Simply call them where appropriate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 authentication or association operation may get stuck for some
reasons, so wpa_supplicant better use an internal timer to recover from
this.
Signed-off-by: Ben Greear <greearb@candelatech.com>
When FT protocol run is completed with FT-EAP, the EAPOL state machine
needs to be notified of the completed authentication to make sure it
does not try to start new authentication.
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.
A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
This was previously done for WPA/WPA2-Personal as part of association
processing when the driver is implementing 4-way handshake. The
portValid needs to be done for WPA/WPA2-Enterprise to get the proper
EAPOL authentication completed callback to configure PMK to the driver.
The driver may get confused if we set the initial TX GTK before having
fully configured and connected to an IBSS, so better delay this
operation until the connection (join/start IBSS) has been completed.
The proto configuration may be left to non-zero when moving from one
configuration to another. To avoid misidentifying a network
configuration as enabling WPA, check key_mgmt field, too.
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The WPS mode was already verified when the AP was configured for
WPA/WPA2, but this was not done with AP that was in open mode.
Fix this by allowing wpa_supplicant_ssid_bss_match() to be called
in non-WPA configuration, too. With this change, wps_pbc BSSID
command will wait until the specified target AP is in active PBC
mode before trying to connect to it.
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Some new code I'm working on will need the scan_res_handler assigned all
the time in certain circumstances, so the easiest way is to reset it
within the handler. This is currently prevented by the way the code in
the event handler works -- change that to permit such usage.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Move the previously SME specific optimization code into generic
function that can be used from non-SME code, too, and use it to
handle disconnection events. In other words, allow disconnection
event to trigger similar optimized scanning case to handle a
common load balancing mechanism. If there is another BSS in the
same ESS when we receive a disconnection event, scan only the
known frequencies of such other BSSes on the next attempt to
speed up recovery.
The special case of requiring blacklisting count to be 2 or higher
is only needed when more than a single network is currently enabled.
As such, we should not do that when only a single network is enabled.
This make the station more likely to follow network side load
balancing attempts where the current AP may disassociate us with
an assumption that we would move to another AP.
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
The wpa_supplicant_event() EVENT_TX_STATUS ack field needs to be
converted to use wpas_send_action_tx_status()
enum p2p_send_action_result in this case, too, to avoid getting
incorrect TX status for P2P processing.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
The driver wrapper may indicate EVENT_CHANNEL_LIST_CHANGED before
completing init(). This would likely result in segfault when driver
channel list is being read as part of processing this event when
P2P is enabled.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
Previously, wpa_supplicant remaining in scanning state without
trying to connect, but there is no particular need to do that.
Instead, cancel WPS operation completely whenever PBC session
overlap is detected.
Disconnection event may be received while in associating state.
Previously, wpa_supplicant could get stuck not trying to reconnect
in that case at least with nl80211. Allow scan request in this
state to avoid the issue. This helps especially with APs that do
load balancing by sending Deauthentication frame as a response to
Reassociation Request frame after successful Authentication frame
exchange.
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
This is needed to avoid trying to reassociate based on new scan
results when using wpa_supplicant to control AP mode. This could
happen if something external triggered the driver to run a scan.
It is possible that l2_packet is not used with wpa_supplicant
in some cases, so better make sure we do not end up notifying
l2_packet code about authentications unless it was actually
initialized in the first place.
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
This allows bgscan modules to use more information to decide on when
to perform background scans. bgscan_simple can now change between
short and long background scan intervals based on signal strength
and in addition, it can trigger immediate scans when the signal
strength is detected to be dropping.
bgscan_simple takes following parameters now:
short interval:signal strength threshold:long interval
For example:
bgscan="simple:30:-45:300"
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
Previously, this was only done with userspace MLME (i.e., driver_test.c);
now, driver_nl80211.c can deliver the FT Action Response (FT-over-DS)
for processing. The reassociation after successful FT Action frame
exchange is not yet implemented.
This is needed to allow the BSS table entry for the previously used
BSS to be removed. Now wpa_bss_in_use() can return 0 for the last BSS
that was used as soon as deauthentication/disassociation event has been
received.
When multiple APs are present in scan results with similar signal
strength, wpa_supplicant may end up bounching between them frequently
whenever new scan results are available (e.g., due to periodic scans
requested by NetworkManager). This can result in unnecessary roaming
and in case of the current cfg80211 version, to frequent network
disconnections.
Do not request a roam if the current BSS is still present in the scan
results and the selected BSS is in the same ESS and has only a slighly
stronger signal strength.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
Get rid of wpa_supplicant_sta_rx() and add a new driver event that is
marked to be used only with driver_test.c. In addition, remove this
functionality from privsep wrapper. This is only use for client mode
MLME testing with driver_test.c.
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
Wait for connection (IBSS join completed) event before marking state
completed. In addition, do not use the station mode authentication
timeout since that can trigger full disconnection from IBSS when
there is a timeout with just one of the peers.
cfg80211/mac80211 can get into somewhat confused state if the AP only
disassociates us and leaves us in authenticated state. For now, force
the state to be cleared with deauthentication to avoid confusing errors
if we try to associate with the AP again. This gets rid of 30 second
delay (scan timeout) in cases where only a disassociation frame is
received from the AP.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
Previously, APs that were hiding SSID (zero-length SSID IE in
Beacon frames) could have been selected when wildcard SSID matching
was used. This would result in failed association attempt since
the client does not know the correct SSID. This can slow down WPS
which is often using wildcard SSID matching.
Ignore BSSes without known SSID in the scan results when selecting
which BSS to use.
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.
This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
If no BSSes/IBSSes matching the enabled networks are found in the scan
results, IBSS/AP mode network (if configured) can be created in
ap_scan=1 mode instead of requiring ap_scan=2 mode to be used whenever
using IBSS or AP mode.
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.
To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).
The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.
The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
After transitioning from DISCONNECTED to SCANNING, we never go back
to DISCONNECTED even though scanning is done or failed.
We're thus stuck in SCANNING while scanning is actually done.
This introduces a new mechanism for collecting notification calls into
a single place (notify.c). As a result of this, most of the
wpa_supplicant code does not need to know about dbus (etc. mechanisms
that could use the notifications). Some empty placeholder functions are
also added in preparation of new dbus code that needs more event
notifications.
If an EAPOL frame is received while wpa_supplicant thinks the driver is
not associated, queue the frame for processing at the moment when the
association event is received. This is a workaround to a race condition
in receiving data frames and management events from the kernel.
The pending EAPOL frame will not be processed unless an association
event is received within 100 msec for the same BSSID.
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons. However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results). Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.
Signed-off-by: Dan Williams <dcbw@redhat.com>
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
Change association behavior to match with ap_scan=1 when WPS is used in
ap_scan=2 mode with wildcard SSID matching. In addition, allow hardcoded
BSSID to be used to select AP even if selected registrar attribute is
not present.
Whenever new scan results include WPS AP(s) and the client is not
associated, send a notification message to control interface monitors.
This makes it easier for GUIs to notify the user about possible WPS
availability without having to go through the scan results.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
delaying Michael MIC error reports by a random amount of time between 0 and
60 seconds if multiple Michael MIC failures are detected with the same PTK
(i.e., the Authenticator does not rekey PTK on first failure report). This
is disabled by default and can be enabled with a build option
CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config.
This may help in making a chopchop attack take much longer time by forcing
the attacker to wait 60 seconds before knowing whether a modified frame
resulted in a MIC failure.
This function was getting way too long, so let's split it into WPA and
non-WPA cases as separate functions. In addition, remove the confusing
"Try to find non-WPA AP" debug message if a WPA-enabled AP is already
selected (as reported by Andriy Tkachuk).
When the initial scan is made, just the cached results from the driver
are used. If this is empty, it's useless to post the results since
another scan is being scheduled immediately. This just causes extra
processing from listeners for no gain.
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
This adds most of the new frame format and identifier definitions from IEEE
802.11w/D6.0. In addition, the RSN IE capability field values for MFP is
replaced with the new two-bit version with MFPC (capable) and MFPR
(required) processing.
