Similar to other cases before, this may end up trying to
send the frame before the carrier state is ready. Ensure
it's ready before sending the frame.
To do that, rename the sync_carrier() function and make
the ifname argument optional.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The kernel has an asynchronous work to enable TX, which hasn't always
run by the time we get to TX tests. Do a sysfs read from the carrier
file before TX, on newer kernels this synchronises the needed state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A test may want to check multicast connectivity independent of unicast
or check multicast without exercising unicast first. Factor out the
multicast connectivity check code into its own function.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
With this command, RSSI signal can be controlled. Due to restrictions in
kernel, only values in the range of [-30, -50] can be used. The command
is implemented by changing the TX power.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Not all driver interfaces provide driver status information with the
local address, so skip the override step if the field is not available.
This is needed, e.g., with macsec_linux.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add success_expected argument to test_connectivity because the function
is expected to fail in some test cases.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add a new test that tests connectivity between two stations that
can't reach each other directly in the mesh, but need forwarding
on another station to talk to each other.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the ap_wds_sta test case to cover post-reassociation case
(both with and without Authentication frame exchange) and add similar
test cases to cover open and WEP cases in addition to this existing
WPA2-PSK test case.
These cover functionality testing for the previous fix in
reassociation-without-new-authentication case. In addition, these find a
new mac80211 issue for the WEP + 4addr combination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hwsim_utils.set_powersace() used to do file operations locally in
python. Start using the cmd_execute() general function for file
operations so that this would also work on remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The regular hwsim tests use both unicast and broadcast frames to test
the connectivity between 2 interfaces. For real hardware (remote hwsim
tests) the broadcast frames will sometimes not be seen by all connected
stations since they can be in low power mode during DTIM or because
broadcast frames are not ACKed. Use 10 retries for broadcast
connectivity tests for real hardware so that the test will pass if we
successfully received at least one of them.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.
Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid unnecessary DATA_TEST_CONFIG calls and wlantest_cli invocations to
speed up the test cases. This drops ap_qosmap execution time from about
14 seconds to under 3 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
This may be needed in some corner cases where broadcast frames with two
associated stations are received by both devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces use of the external hwsim_test tool for most data
connectivity test cases. Only the cases where a special interface
(bridge/VLAN) is used are still executed through hwsim_test.
The internal DATA_TEST_* functionality makes it easier to extend the
connectivity test cases through an external device with real WLAN
hardware instead of the hwsim test setup. In addition, the error reports
from this code can be made more informative.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that IP packets with various DSCP values are mapped to the
correct TID both with default mapping and with custom QoS mappings.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
print and logger.info() were directing output to different locations
(stdout and stderr, respectively) which resulted in buildbot showing
reordered entries. Use logger consistently to avoid that.
Signed-hostap: Jouni Malinen <j@w1.fi>
run-p2p-tests.py can now be used to run all P2P test cases. The
actual test cases are defined in test_p2p_*.py files.
Signed-hostap: Jouni Malinen <j@w1.fi>
