Signal strength was sorted lexically rather than numerically, which
put "-100 dBm" before "-50 dBm" if sorted in descending order.
This change fixes that. It also treats frequency in the same
manner, preparing it for the IEEE 802.11ah.
Signed-off-by: Adrian Nowicki <adinowicki@gmail.com>
Reorder scanning in a way that allows the ER behavior to be more
predictable. The first Probe Request report is for a previously received
frame on the AP and this new sequence avoids leaving either of the PBC
test STAs to be that one.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes testing under very heavy load or under extensive kernel
debugging options more robust by allowing number of test cases to scan
multiple times before giving up on active scans. The main reason for
many of the related test failures is in Probe Response frame from
hostapd not getting out quickly enough especially when multiple BSSes
are operating.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that PBC session overlap detection does not get indicated
when forming the group with the same peer multiple times.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new wpa_supplicant configuration parameter can be used to force
passive scanning to be used for most scanning cases at the cost of
increased latency and less reliably scans. This may be of use for both
testing purposes and somewhat increased privacy due to no Probe Request
frames with fixed MAC address being sent out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test case for a specific sequence that could result
in wpa_supplicant NULL dereference when a SD request is cancelled before
the SD Request TX status callback has been processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A NULL pointer crash was caused by commit
7139cf4a4f ('P2P: Decrement
sd_pending_bcast_queries when sd returns'). p2p->sd_query can be cleared
to NULL whenever a query is cancelled, even in case the request had
already been transmitted. As such, need to be prepared for the query not
remaining when processing TX status callback for the frame.
Crashes on 2ee98 in following code
2ee90: f7fc f8b6 bl 2b000 <p2p_dbg>
2ee94: e02c b.n 2eef0 <p2p_send_action_cb+0x348>
2ee96: 6c25 ldr r5, [r4, #64] ; 0x40
2ee98: 68ee ldr r6, [r5, #12]
2ee9a: b166 cbz r6, 2eeb6 <p2p_send_action_cb+0x30e>
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
libnl uses a pretty small buffer (32 kB that gets converted to 64 kB) by
default. It is possible to hit that limit in some cases where operations
are blocked, e.g., with a burst of Deauthentication frames to hostapd
and STA entry deletion. Try to increase the buffer to make this less
likely to occur.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ANQP verification/parsing is done only after the GAS_DONE indication
is sent over the control interface. This means that in case the ANQP
parsing fails there is no indication to the upper layers. Add an
ANQP-QUERY-DONE event that reports the status of the ANQP parsing.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
The icon files and the osu-providers.txt that are generated may not have
proper permission for external programs to access. Set the access
permissions to the same as the permissions for osu_dir.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
Incorrect TrustRoot path "PolicyUpdate/TrustRoot" was used. The
TrustRoot path is required to be "Policy/PolicyUpdate/TrustRoot" as
defined in Section 9.1 of Hotspot 2.0 (Release 2) specification. Fix the
path to "Policy/PolicyUpdate/TrustRoot".
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
Previously, both failure and success cases used same return value 0.
Indicate failures differently to make hs20-osu-client return value more
useful for subscription remediation cases.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
If TLS encryption fails, encr may be NULL and that would have resulted
in NULL pointer dereference..
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
In wpa_cli_cmd_interface(), try_connection(), and main(), ctrl_ifname
may be NULL and could be dereferenced depending on the printf()
implementation.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
In ieee802_1x_decapsulate_radius(), eap_server_get_name() may return
NULL, and it could be dereferenced depending on printf implementation.
Change it to return "unknown" instead for the case of no matching EAP
method found. This makes it easier for the callers to simply print this
in logs (which is the only use for this function).
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Stop any ongoing P2P listen/find flow before starting invitation flow.
This was partially handled in p2p_invite() that called p2p_find(), but
this did not cleanly handle cases such as long_listen.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
We were copying the NL80211_ATTR_EXT_CAPA attribute into the
extended_capa_mask element, which is incorrect. Use
NL80211_ATTR_EXT_CAPA_MASK instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
A control interface call to flush the current state used the
current wpa_s to clear the P2P state even though it might not
be the interface controlling the P2P state.
Fix it by using the correct interface to flush the P2P state.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Publish support for Tx STBC in the HT capabilities of a GO and AP
controlled by wpa_supplicant in case the hardware supports it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Clear the reattach flags, in case a connection request did not trigger a
scan. This needs to be done to avoid leaving the reattach flag set for
the next scan operation which may not have anything to do with the
specific request that could have been optimized using the single-channel
single-SSID scan.
Signed-off-by: Ben <ben.rosenfeld@intel.com>
Use interface's own NFC configuration instead of parent's one
to support a P2P device dedicated interface.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The length should be 14 and not 10.
The current situation causes failure during parsing of the command.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
This restores some of the pre-radio work behavior for scanning by
retrying scan trigger if the driver rejects it (most likely returning
EBUSY in case of nl80211-drivers). Retry is indicated in the
CTRL-EVENT-SCAN-FAILED event with "retry=1".
For manual scans (e.g., triggered through "SCAN" control interface
command), no additional retries are performed. In other words, if upper
layers want to retry, they can do so based on the CTRL-EVENT-SCAN-FAILED
event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ce7b56afab ('WPS: Fix an
interoperability issue with mixed mode and AP Settings') added code to
filter M7 Authentication/Encryption Type attributes into a single bit
value in mixed mode (WPA+WPA2) cases to work around issues with Windows
7. This workaround was lost in commit
d7a15d5953 ('WPS: Indicate current AP
settings in M7 in unconfigurated state') that fixed unconfigured state
values in AP Settings, but did not take into account the earlier
workaround for mixed mode.
Re-introduce filtering of Authentication/Encryption Type attributes for
M7 based on the current AP configuration. In other words, merge those
two earlier commits together to include both the earlier workaround the
newer fix.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the possibility to define a subset of channels used by the ACS
engine when not operating on DFS channels.
Signed-off-by: Adrien Decostre <ad.decostre@gmail.com>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the inactivity check returns that there is no entry remaining for the
STA in the kernel, drop the STA in hostapd as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
It was possible for an out-of-memory code path to trigger NULL pointer
dereference when preparing a RADIUS accounting report.
Signed-off-by: Jouni Malinen <j@w1.fi>
This set of notes provides information on how virtual guess OS can be
used to run the mac80211_hwsim test cases under any host OS. The
specific example here uses Ubuntu 14.04.1 server as the starting point
and lists the additional packages that need to be installed and commands
that can be used to fetch and build the test programs.
Signed-off-by: Jouni Malinen <j@w1.fi>
There were couple of common cases where the control interface for the
dynamic wpa_supplicant instance could have been left in attached state
until Python ends up cleaning up the instance. This could result in
issues if many monitor interface events were queued for that attached
socket. Make this less likely to cause issues by explicitly detaching
and closing control interfaces before moving to the next test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is easier to debug issues related to the wpa_supplicant control
interfaces being left behind in attached state when the debug log file
can be used to determine whether a specific monitor socket was a global
or per-interface one.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Action frame used for entring WNM Sleep Mode to
get dropped on the AP side due to it arriving prior to having processed
EAPOL-Key message 4/4 due to a race condition between Data and
Management frame processing paths. Avoid this by waiting for
AP-STA-CONNECTED event from hostapd prior to trying to enter WNM Sleep
Mode. In addition, make the check for the STA flag change more robust by
allowing the wait to be a bit longer with a loop that terminates as soon
as the flag has changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When the STA is forced to disconnect immediately after completion of
4-way handshake, there is a race condition on the AP side between the
reception of EAPOL-Key msg 4/4 and the following Deauthentication frame.
It is possible for the deauthentication notification to be processed
first since that message uses different path from kernel to user space.
If hostapd does not receive EAPOL-Key msg 4/4 prior to deauthentication,
no PMKSA cache entry is added. This race condition was making the test
cases expecting PMKSA caching to work to fail every now and then. Avoid
this issue by waiting for AP-STA-CONNECTED event from hostapd. This
makes sure the PMKSA cache entry gets added on the AP side.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case is failing every now and then, so add some
more time for the olbc_ht value to get updated before reporting a
failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
