This verifies that pmf=2 is ignored for a non-RSN network while a
network profile specific ieee80211w=2 is enforced.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that a WPA2PSK passphrase with control characters gets
rejected in a WPS Credential and that control characters in SSID get
written as a hexdump.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a dedicated P2P Device interface is used, its configuration should
be cloned to the group interface. Add a test that covers this both when
a separate group interface is used and not.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use the global control interface to remove P2P network blocks, to
support cases when a dedicated P2P Device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some environments define default system wide HTTP proxy. Using default
system configuration may result in a failure to open some HTTP URLs. Fix
this by ensuring that no proxies are used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In p2p_channel_vht80_autogo and p2p_channel_vht80p80_autogo, parse the
P2P-GROUP-STARTED event prior to calling the group_request() method, as
otherwise the group ifname is not set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Support configurations that use a dedicated P2P Device interface by
using the global control interface and specifying the interface name for
the GET commands fetching the ip_addr_go parameter.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Modify the persistent_group_profile_add test to support configurations
that use a dedicated P2P Device interface by sending the ADD_NETWORK and
SET_NETWORK commands on the global control interface and specifying the
P2P Device interface name.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add an attribute to class WpaSupplicant with the name of the
P2P Device interface. If a separate interface is not used for
P2P Device, this attribute will hold the name of the only used
interface (with functions also as the P2P Device management
interface).
This attribute will be used to direct P2P related commands to the
P2P Device interface, which is needed for configurations that use
a separate interface for the P2P Device.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Waiting for the P2P-DEVICE-FOUND event should be done on the global
control interface to support configurations that use a dedicated P2P
Device interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Support configurations that use a dedicated P2P Device interface by
sending the P2P_CONNECT command on the global control interface.
In addition, when a dedicated P2P Device interface is used, there is no
need to manually respond to the Provision Discovery Request since the
request is processed by the P2P Device interface and this interface was
not set for external RX management frames handling.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This fixes commit 2f0f69a9ec ('tests: Use
p2ps_provision() and p2ps_connect_pd() in p2ps_connect_p2ps_method()').
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
1. Fail roaming to an AP which exceeded its number of allowed stations.
2. Fail roaming due to passphrase mismatch.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
It is better to use a list of command line arguments for the local
execution case and convert that to a space-separated string for the
remote case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the DFS test cases that use start_dfs_ap() more usable for
testing with remote hosts.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass apdev to instead of HostapdGlobal() to invalid_ap() to make the
dynamic AP test cases more useful for testing with remove hosts.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Use hostapd.add_ap() and hostapd.remove_bss() to avoid direct
HostapdGlobal() use in some of the dynamic AP test cases to make them
more usable for testing with remote hosts.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass apdev param to hostapd.add_bss(). Kill hardcoded phy param and get
phy base on apdev. These are needed to support operation with a remote
test host.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
We need this for remote host support. From apdev we can get
apdev['hostname'] and apdev['port'].
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
1. Add tests for hostapd neighbor database and neighbor report and
request. Remove the partial neighbor report request test from
test_wpas_ctrl.py since they are now covered more completely in
test_rrm.py.
2. Add LCI request test.
3. Add FTM range request signaling test. This covers only the control
interface commands and measurement request/response exchange for now.
Full end-to-end functionality requires support of station reporting
RRM capability.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Use quotation marks to match the new SSID encoding format in the
NEIGHBOR_REP_REQUEST command. In this specific test case, the exact SSID
value did not make any difference for behavior. The previous version
ended up getting decoded as a hexstring after the NEIGHBOR_REP_REQUEST
format change. The new version goes back to the ASCII string version of
"abcdef".
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Modify the test cases to tests the Hotspot 2.0 filtering functionality
in wpa_supplicant, instead of testing only the kernel interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The new persistent_group_peer_dropped3 test case is similar to
persistent_group_peer_dropped with the difference being in the
responding device (the one from which the persistent group information
is dropped) is not issued a separate P2P_LISTEN command and instead, a
single P2P_FIND is used through the exchange to verify that this
operation does not get stopped unexpectedly. This is a regression test
case to verify that P2P_PENDING_INVITATION_RESPONSE case ends up calling
p2p_check_after_scan_tx_continuation() in non-success case. It should be
noted that this is dependent on timing: Action frame TX request needs to
occur during the P2P_FIND Search phase (scan). As such, not every
execution of this test case will hit the previous issue sequence, but
that should be hit every now and then.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (7) converts the cases where a local variable is used to store
apdev[#]['ifname'] before passing it as the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (6) converts the cases where apdevs[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (5) converts the cases that use the start_ap_wpa2_psk() helper
function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (3) converts the cases that use the start_ap() helper
function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (2) converts the cases that use the add_ssdp_ap() helper
function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This allows the full apdev dict to be passed to the add_ap() function
instead of just ifname. This allows us to handle also remote hosts while
we can check apdev['hostname'], apdev['port']. The old style ifname
argument is still accepted to avoid having to convert all callers in a
single commit.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The test cases fst_ap_start_session_oom and fst_setup_mbie_diff did not
clean up FST sessions properly in case alloc_fail failed due to missing
support for it in the build. This could result in abandoning attached
hostapd global control interface monitors and test case failures due to
the global control interface socket running out of output buffer.
Fix this by going through the cleanup steps even if alloc_fail raises
HwsimSkip exception.
Signed-off-by: Jouni Malinen <j@w1.fi>
For now, this is not enforcing cfg80211 reassociation since the needed
changes do not yet exist in the upstream kernel. Once those changes are
accepted, the TODO note in the test case can be addressed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This needs to be allowed with OpenSSL 1.1.0 since the RC4-based cipher
has been disabled by default.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This class allows execution of commands on a remote hosts/machine. This
is based on ssh with authorized keys, so you should be able to execute
such commands without any password:
ssh <user>@<hostname> id
By default user is root.
Support for sync and async calls is included.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is needed for ap_vlan_tagged_wpa2_radius_id_change to pass. The
ioctl-based vlan_add() function does not use the vlan_if_name parameter
at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
The no self.global_iface case was not returning the result from the
self.request() case. While this is not really a path that is supposed to
be used, make it return the response since it is at least theoretically
possible to get here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow updated Interworking behavior that adds the
realm to the EAP-Response/Identity value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect path and file name was used in the openssl command to generate
one of the OCSP responses. Also fix
ap_wpa2_eap_tls_intermediate_ca_ocsp_multi to expect success rather than
failure due to OCSP response. Based on the test description, this was
supposed to succeed, but apparently that root_ocsp() bug prevented this
from happening.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
