The ap_sta_deauth_cb and ap_sta_disassoc_cb eloop timeouts are used to
clear a disconnecting STA from the kernel driver if the STA did not ACK
the Deauthentication/Disassociation frame from the AP within two
seconds. However, it was possible for a STA to not ACK such a frame,
e.g., when the disconnection happened due to hostapd pruning old
associations from other BSSes and the STA was not on the old channel
anymore. If that same STA then started a new authentication/association
with the BSS, the two second timeout could trigger during this new
association and result in the STA entry getting removed from the kernel.
Fix this by canceling these eloop timeouts when receiving an indication
of a new authentication or association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When multiple interfaces across mutiple radios are started using a
single instance of hostapd, they all come up at different times
depending upon how long the ACS and HT scan take on each radio. This
will result in stations (that already have the AP profile) associating
with the first interfaces that comes up. For example in a dual band
radio case (2G and 5G) with ACS enabled, 2G always comes up first
because the ACS scan takes less time on 2G and this results in all
stations associating with the 2G interface first.
This feature brings up all the interfaces at the same time. The list of
interfaces specified via hostapd.conf files on the command line are all
marked as sync interfaces. All the interfaces are synchronized in
hostapd_setup_interface_complete().
This feature is turned on with '-S' commmand line option.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Fix and extend the ieee80211_freq_to_channel_ext() function to deal
correctly with VHT operating classes (128, 129, 130).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The hostapd_hw_get_channel() function can't be used to convert center
frequencies to channel numbers, because the hw mode lists don't have all
the center frequencies. The hw mode lists have the main channel
frequencies and flags to indicate the channel topography.
For instance, channel 5805 with VHT80- has the channel center frequency
segment 0 at 5775. This segment is only indicated indirectly in the hw
mode list by the HOSTAPD_CHAN_VHT_50_30 flag. The hw mode list doesn't
have any elements with frequency 5775 to allow the conversion to a
channel number. Thus, we need to use ieee80211_freq_to_chan() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Extended channel switch provides an ability to switch between operating
classes and is required for P2P Devices by the P2P specification when
switching in 5 GHz.
When the operating class is provided for channel switch, the AP/P2P GO
will use eCSA IE in addition to the regular CSA IE both on 2.4 GHz and 5
GHz bands.
Transitions between different hw_modes are not supported.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When building Beacon and Probe Response frames for the target channel,
consider bandwidth parameter for VHT channels. In addition, add support
for updating vht_oper_centr_freq_seg0_idx and
vht_oper_centr_freq_seg1_idx.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reset hapd->num_probereq_cb to 0 on an interface deinit to avoid
unexpected behavior if the same interface is enabled again without fully
freeing the data structures. hostapd_register_probereq_cb() increments
hapd->num_probereq_cb by one and leaves all old values unchanged. In
this deinit+init case, that would result in the first entry in the list
having an uninitialized pointer and the next Probe Request frame
processing would likely cause the process to terminate on segmentation
fault.
This issue could be hit when hostapd was used with WPS enabled (non-zero
wps_state configuration parameter) and control interface command DISABLE
and ENABLE were used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd can now be configured to track unconnected stations based on
Probe Request frames seen from them. This can be used, e.g., to detect
dualband capable station before they have associated. Such information
could then be used to provide guidance on which colocated BSS to use in
case of a dualband AP that operates concurrently on multiple bands under
the control of a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the hostapd global control interface ADD command to allow
driver wrapper to be specified ("ADD <ifname> <ctrl_iface> <driver>").
Previously, this case that did not use a configuration file allowed only
the default driver wrapper to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This event was previously used only when disabling AP mode operation
through hostapd control interface. Make this more consistent by
providing same indication when disabling hostapd interface through the
interface deinit path. This adds the event to the case where a full
hostapd radio instance is removed which also applies for the
wpa_supplicant AP mode operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
If HT40 co-ex scan fails due to the driver rejecting scan triggers
multiple times, it was possible for the ap_ht40_scan_retry() timeout
being left behind and it getting run after hapd->drv_priv has been
cleared. This would result in NULL pointer dereference in
driver_nl80211_scan.c. Fix this by canceling the timeout when disabling
the interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends Disconnect-Request processing to check against PMKSA cache
entries if no active session (STA association) match the request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the first matching STA was picked. That is not really the
design in RFC 5176, so extend this matching code to go through all
specified session identification attributes and verify that all of them
match. In addition, check for a possible case of multiple sessions
matching. If such a case is detected, return with Disconnect-NAK and
Error-Code 508 (multiple session selection not supported).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The local conf pointer needs to be cleared once it gets assigned to
hapd_iface to avoid double-free of the configuration data on error path.
Signed-off-by: Jouni Malinen <j@w1.fi>
The per-BSS configuration information needs to be freed if hostapd fails
to add a new interface for a BSS added with "ADD bss_config=..."
command.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd_alloc_bss_data() failed to allocate the struct hostapd_data
instance, dynamic interface addition path ended up trying to dereference
freed memory due to incorrect cleanup steps. Fix this by decrementing
the interface count when the newly added interface is removed. In
addition, make the setup more robust by clearing all changes within
hostapd_data_alloc() if any of the allocations fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the struct hostapd_data variables get initialized with allocated
memory in the P2P GO case even before hapd->started has been set to 1.
As such, hostapd_free_hapd_data() needs to free these even if
!hapd->stated.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a possible race condition between receiving the
NEW_PEER_CANDIDATE event and the Authentication frame from the peer.
Previously, if the Authentication frame RX event was indicated first,
that frame got dropped silently. Now, this frame is still dropped, but a
copy of it is stored and the frame gets processed on the following
NEW_PEER_CANDIDATE event if that is received for the same peer within
two seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
If "ADD bss_config=" command failed in driver_init() or
hostapd_setup_interface(), some of the allocated resources were not
freed properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit establishes the infrastructure, and handles the Neighbor
Solicitation and Neighbor Advertisement frames. This will be extended
in the future to handle other frames.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.
This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Modify hostapd.c logic to add checks for valid mconf data structure:
- For hostapd_setup_bss we don't need to flush old stations in case
we're rejoining a mesh network.
- In hostapd_setup_interface_complete, we don't need to setup the
interface until we join the mesh (same reasoning for
hostapd_tx_queue_params).
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).
When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This fixes couple of code paths where the WPA_DRIVER_FLAGS_DFS_OFFLOAD
flag was not checked properly and unexpected DFS operations were
initiated (and failed) in case the driver handles all these steps.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use an explicit memset call to clear any hostapd configuration parameter
that contains private information like keys or identity. This brings in
an additional layer of protection by reducing the length of time this
type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
It's worth giving a try to fallback to re-starting BSSes at least once
hoping it works out instead of just leaving BSSes disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Earlier commit related to MAC address based access control list
offloaded to the driver was not sending ACL configuration to the driver
if the MAC address list was empty. Remove this check as empty access
control list is a valid use case and sending ACL parameters should not
be dependent on whether the list is empty.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Couple of code paths in hostapd.c could have left hapd->drv_priv
pointing to memory that was freed in driver_nl80211.c when a secondary
BSS interface is removed. This could result in use of freed memory and
segfault when the next driver operation (likely during interface
deinit/removal). Fix this by clearing hapd->drv_priv when there is
reason to believe that the old value is not valid within the driver
wrapper anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
These three calls were used already in three different paths. Use a
helper function to avoid adding even more copies of this.
Signed-off-by: Jouni Malinen <j@w1.fi>
If for some reason interface setup fails mid-way when setting up
multi-BSS AP it was possible to get segmentation fault because driver
was not properly cleaned up.
One possible trigger, when using nl80211 driver, was udev renaming an
interface created by hostapd causing, e.g., linux_set_iface_flags() to
fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
This variable is updated when calling hostapd_if_add(), so it makes
sense to do the same thing when calling hostapd_if_remove().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Performing, e.g. `wpa_cli -p /var/run/hostapd raw DISABLE` twice led to
hostapd segmentation fault if multiple BSSes were configured. Fix this
by checking if there is anything to disable at all before trying.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
The current RADIUS server pointer was updated after each SET command
which broke parsing of multiple RADIUS servers over the control
interface. Fix this by doing the final RADIUS server pointer updates
only once the full configuration is available.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, hostapd had to be started with at least one of the
configuration files enabling TNC for TNC to be usable. Change this to
allow TNC to be enabled when the first interface with TNC enabled gets
added during runtime.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the initial OBSS scans in AP mode before starting 40 MHz BSS
more robust. In addition, HT20 can be used as a backup option if none of
the scans succeed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When primary and secondary channel were switched and config was
reloaded, secondary channel was incorrectly overwritten.
Proceed as for other settings that should not be changed and don't
allow to overwrite.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Especially when multiple BSSes are used with ACS, number of the error
paths were not cleaning up driver initialization properly. This could
result in using freed memory and crashing the process if ACS failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was possibility that the current channel in Beacon information
element was incorrectly set. This problem was easily observed when
primary and secondary channel were switched and then some of hostapd
settings (for example password) were changed using WPS External
Registrar. This caused hostapd_reload_config() function overwrite the
current channel information from config file.
This patch prevents this situation and does not allow to overwrite
channel and some other settings when config is reloaded.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
It was possible for the control interface and some of the BSS setup to
be left partially initialized in failure cases while the BSS structures
were still freed. Fix this by properly cleaning up anything that may
have passed initialization successfully before freeing memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, some of the last initialization steps could fail without
clearly marking the interface disabled. For example, configuring the
channel to the driver could fail, but hostapd would not clearly identify
as the interface not being in functional state apart from not moving it
to the ENABLED state. Send an AP-DISABLED event and mark interface state
DISABLED if such a setup operation fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this was enabled only at msgdump verbosity level, but any
level that is more verbose than it should also be included.
Signed-off-by: Jouni Malinen <j@w1.fi>
handle_assoc_cb() got this addition, but the check in
hostapd_new_assoc_sta() was not modified to be aware of the OSEN special
case for EAPOL state machines to be used for marking a STA authorized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was done in handle_assoc_cb() in ieee802_11.c for drivers that use
hostapd SME/MLME. However, drivers that include SME/MLME implementation
do not use that function and the STA flag needs to be set when
processing the association notification. This is needed to get the STA
entry into showing the proper authorized state and to get the
AP-STA-CONNECTED/DISCONNECTED events on the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
If hapd_iface->bss[i] == NULL, this could have resulted in NULL pointer
dereference in the debug print. Avoid this by skipping the message in
case of NULL pointer. In addition, clear iface->bss[i] to NULL for
additional robustness even though this array gets freed immediately.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like leaving behind the freed pointed at the end of the array
could end up in a crash triggered by double free in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows NAS-IP-Address, NAS-Identifier, and NAS-IPv6-Address to be
included in the Disconnect-Request packets.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a station is disconnected based on Disconnect-Request, it is better
to force the station to go through full EAP authentication if it tries
to reconnect.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Before this patch, 1 second timeout was used for regulatory updates. In
some cases, specially when we reload driver modules on some slower
platforms this could take more than 1 second (about 2 seconds). This is
important specially for DFS case, where we have to have correct DFS
region before we will start CAC. In other case (unknown DFS region), CAC
will fail. 5 seconds should be enough for all cases.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
It is possible for the configuration to be temporarily invalid when
adding a new AP through SET commands followed by ENABLE. Avoid this
issue by using less strict validation on SET commands and perform full
configuration validation only on ENABLE. Use cases with configuration
file maintain their previous behavior, i.e., full validation after the
file has been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
When CSA flow starts, store the entire struct hostapd_freq_params and
not only CS frequency as it was before. The additional freq_params are
required to advertise CS supplementary IEs such as secondary channel,
wide bandwidth CS, etc.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If more BSSes are added in config file than are supported by the driver,
segmentation fault can appear. For this case, the interface_added flag
needs to be cleared if adding a new BSS fails.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.
For now, force all BSSs to be removed in case the first one is removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().
Signed-hostap: Jouni Malinen <j@w1.fi>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
