To allow for a PASN station to deauthenticate from an AP to clear any
PTKSA cache entry for it, extend the nl80211 interface to allow sending
a Deauthentication frame with off channel enabled.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Send a flag to the kernel when user has specified disable_he=1 in the
network configuration block. This extends the functionality added in
commit 7c8f540ee0 ("wpa_supplicant: Add HE override support") to cover
the cases that need kernel functionality.
Signed-off-by: Ben Greear <greearb@candelatech.com>
In addition, make the compiler warn if a new enum value is added without
defining the matching mapping to a string.
Signed-off-by: Jouni Malinen <j@w1.fi>
The nl_connect is initialized with the process_bss_event() handler.
However, it is used several times with the default valid handler. As a
result, if a message that is only valid for process_bss_event() is
received while the default handler is used, it will be dropped.
This has been observed in a case where during the 4-way handshake, a
Beacon frame is received on the AP side, which triggers a beacon update,
just before receiving the next EAPOL. When send_and_recv_msgs_owner() is
called for sending the NL80211_CMD_SET_BEACON command, the
NL80211_CMD_CONTROL_PORT_FRAME event is already pending. As a result, it
is received with the default handler, which drops it. Since the EAPOL
frame is dropped, the connection attempt fails.
Fix it by using the process_bss_event() handler when the nl_connect
handler is used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Use a helper function as the do_acs() callback to allow builds to pull
in all the vendor specific operations into a single binary.
Signed-off-by: Jouni Malinen <j@w1.fi>
BRCM vendor command used to trigger ACS scan. After ACS finished,
DHD driver will send results by event BRCM_VENDOR_EVENT_ACS.
Signed-off-by: Xinrui Sun <xinrui.sun@broadcom.com>
Previously nl80211_nlmsg_clear() would be called under a special
condition when valid_handler is NULL and valid_data is -1. Such API is
not very convenient as it forces the handler to be NULL. Change the
send_and_recv() function to always clear the nl_msg, which will simplify
all this logic.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the driver SME is used, offloaded handshakes which need Operating
Channel Validation (OCV) such as SA Query procedure, etc. would fail if
hostapd enables OCV based on configuration but the driver doesn't
support OCV. To avoid this when driver SME is used, enable OCV from
hostapd only when the driver indicates support for OCV.
This commit also adds a capability flag to indicate whether driver SME
is used in AP mode.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
When the driver SME is used, offloaded RSN handshakes like SA Query, GTK
rekeying, FT authentication, etc. would fail if wpa_supplicant enables
OCV in initial connection based on configuration but the driver doesn't
support OCV. To avoid such failures check the driver's capability for
enabling OCV when the driver SME used.
This commit also adds a capability flag for indicating OCV support
by the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Enabling beacon protection will cause STA connection/AP setup failures
if the driver doesn't support beacon protection. To avoid this, check
the driver capability before enabling beacon protection.
This commit also adds a capability flag to indicate beacon protection
support in client mode only.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Unsolicited broadcast Probe Response transmission is used for in-band
discovery in the 6 GHz band (IEEE P802.11ax/D8.0 26.17.2.3.2, AP
behavior for fast passive scanning). Add support for configuring the
parameters for such frames.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add hostapd configuration options for unsolicited broadcast
Probe Response transmission for in-band discovery in 6 GHz.
Maximum allowed packet interval is 20 TUs (IEEE P802.11ax/D8.0
26.17.2.3.2, AP behavior for fast passive scanning).
Setting value to 0 disables the transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add hostapd configuration parameters for FILS Discovery frame
transmission interval and prepare a template for FILS Discovery frame
for the driver interface. The actual driver interface changes are not
included in this commit.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
The HE 6 GHz capability was not being sent to the kernel causing 6 GHz
support being unidentifiable in the kernel driver for added stations.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Extend SPR element to support following fields and pass all
information to kernel for driver use.
* Non-SRG OBSS PD Max Offset
* SRG BSS Color Bitmap
* SRG Partial BSSID Bitmap
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Allow HE MCS rate to be used for beacon transmission when the driver
advertises the support. The rate is specified with a new beacon_rate
option "he:<HE MCS>" in hostapd configuration.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use the correct enum nl80211_band value when configuring the beacon rate
for the 6 GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Add option 2 to the p2p_device_random_mac_addr configuration option to
support device drivers which use by default random MAC adresses when
creating a new P2P Device interface (for instance, the BCM2711 80211
wireless device driver included in Raspberry Pi 4 Model B). In such
case, this option allows to create the P2P Device interface correctly
when using P2P permanent groups, enabling wpa_supplicant to reuse the
same MAC address when re-invoking a P2P permanent group.
update_config=1 is required.
Signed-off-by: Ircama <amacri@tiscali.it>
Messages such as RTM_IFNFO or RTM_IFANNOUNCE could have been lost.
As such, sync the state of our internal driver to the state of the
system interfaces as reports by getifaddrs(2).
This change requires the routing socket be placed in non-blocking
mode. While here, set the routing and inet sockets to close on exec.
BSDs that support SO_RERROR include NetBSD and DragonFly.
There is a review underway to add this to FreeBSD.
Signed-off-by: Roy Marples <roy@marples.name>
There's no point in attempting to configure frame filters on
a P2P-Devices that doesn't even have a netdev (nor passes any
data traffic), that just results in error messages. Skip it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:
- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.
Add support for advertising the new capabilities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for new channels 173 and 177 in the operating classes 125 to
130 as defined in draft IEEE P802.11ax/D8.0.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
When wpa_supplicant sends NL80211_CMD_AUTHENTICATE to kernel, it is
possible that the cfg80211 in kernel has expired the BSS entry that
we are trying to auth with. Then cfg80211 will reject the auth cmd.
In this case, wpa_supplicant will trigger a single channel scan to
refresh cfg80211 BSS entry, and retry the auth when scan is finished.
When this case happens, wpa_supplicant makes a copy of auth params,
such as frequency, bssid, ssid, ie and so on. So when we retry auth,
the copy of these params will be used. The problem is, a param named
auth_data is missed when making the copy. The auth_data is used by
NL80211_ATTR_SAE_DATA which is a mandatory field for WPA3-SAE auth.
In WPA3-SAE case the auth retry will always fail because auth_data is
missing. This patch fixes the issue.
Signed-off-by: hongwang.li <hongwang.li@sonos.com>
Android has a mechanism to extend the driver interface in vendor
specific ways. This implementation of the vendor interface is done in
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB). Extend this to allow the vendor
events to be provided to this library to facilitate the event
processing.
Introduce a new board configuration via
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB_EVENT) rather than reusing
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB) to enable this event handling in the
private library. This is to avoid compilation issues for
wpa_driver_nl80211_driver_event() with the already existing private
library implementations defined with
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
NL80211_CMD_ROAM indication is scheduled via a kernel work queue, while
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH is a vendor event from the
driver. Thus, a race condition can exist wherein the vendor event is
received prior to the NL80211_CMD_ROAM indication.
The processing of this vendor event depends on the NL80211_CMD_ROAM
indication to update the roamed BSS/BSSID information and thus the out
of sequence processing of these events would result in not updating the
right BSS information.
This commit adds a workaround to hold the pending
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event for up to 100 ms in
case NL80211_CMD_ROAM is not received first.
Signed-off-by: Purushottam Kushwaha <pkushwah@codeaurora.org>
After a disconnect command is issued, wpa_supplicant generates a
disconnection event to self and ignores the next disconnection event
coming from the driver. In a race condition in which the driver
generates a connected event due to roaming just before receiving the
disconnect command from userspace, wpa_supplicant processes the
connected event after processing the self-generated disconnection event
and enters WPA_COMPLETED state. The driver sends a disconnection event
after processing the disconnect command sent by wpa_supplicant but the
disconnection event is ignored by wpa_supplicant as the disconnection
event is considered to be a result of locally generated disconnect
command. Thus, wpa_supplicant continues to be in the connected
(WPA_COMPLETED) state though the driver is in disconnected state.
Fix this out-of-sync behavior between the driver and wpa_supplicant by
not ignoring the disconnection event from the driver because of the
locally generated disconnect command sent to the driver if there is a
connection event received after issuing the disconnect command to the
driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
When the driver sends a CQM RSSI threshold event, wpa_supplicant queries
the driver for the signal and noise values. However, it is possible that
by that time the station has already disconnected from the AP, so these
values are no longer valid. In this case, indicate that these values are
invalid by setting them to WPA_INVALID_NOISE.
Previously a value of 0 would be reported, which may be confusing as
this is a valid value.
Since nl80211_get_link_signal() and nl80211_get_link_noise() already set
invalid values for a case of failure, just use the value set by these
functions even if they fail.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The kernel requires indication of DFS handler residing in user space
(NL80211_ATTR_HANDLE_DFS) to enable DFS channels.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
mac80211 does not allow mgmt tx to use off channel on
DFS channels in non-ETSI domain, because it will invalidate
CAC result on current operating channel.
(mac80211 commit: 34373d12f3cbb74960a73431138ef619d857996f)
Hence don't set offchanok for mgmt tx in case of DFS channels
in non-ETSI.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Use NL80211_ATTR_SAE_PWE attribute to indicate the sae_pwe value
to the driver during the NL80211_CMD_START_AP and NL80211_CMD_CONNECT
in WPA3-Personal networks which are using SAE authentication.
Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
Add support to report a vendor specific connect fail reason code fetched
from the driver to users by adding the reason code to the event
CTRL-EVENT-ASSOC-REJECT. Fetch the connect fail reason code when the
driver sends a failure connection result and append the reason code, if
available, to assoc reject event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The newer kernel versions enforce strict netlink attribute policy
validation and will cause cfg80211 to reject vendor commands with
NL80211_ATTR_VENDOR_DATA if NLA_F_NESTED attribute is not set but
if the vendor command is expecting nested data within
NL80211_ATTR_VENDOR_DATA attribute.
Most of the earlier instances were addressed by adding NLA_F_NESTED
flag in nla_nest_start(). This commit addresses the remaining
instance in which NL80211_ATTR_VENDOR_DATA is populated using data
set by user through the control interface.
Enhance the control interface VENDOR command to indicate whether the
vendor subcommand uses nested attributes within NL80211_ATTR_VENDOR_DATA
attribute or not.
Set NLA_F_NESTED flag for existing QCA vendor commands which use nested
attributes within the NL80211_ATTR_VENDOR_DATA attributes so that the
old frameworks implementations for already existing commands work
without any issues.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The loop for removing unsupported bands was assuming there is always
exactly one band/mode following the removed band. That was not at all
correct, so fix this by dynamically determining how many (if any) bands
need to be moved.
Fixes: 106d67a93c ("nl80211: Filter out unsupported bands")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When nlmsg allocation fails, nl80211_drv_msg() returns NULL and the call
to send_and_recv_msgs_owner() from nl80211_leave_ibss() could have ended
up dereferencing a NULL pointer. Fix this by make
send_and_recv_msgs_owner() more consistent with other send_and_recv*()
cases that check msg == NULL internally.
Fixes: 12ea7dee31 ("nl80211: Use nl80211 control port for receiving EAPOL frames")
Signed-off-by: Pooventhiran G <pooventh@codeaurora.org>
If the driver indicates capability for a band that
hostapd/wpa_supplicant does not support, the struct hostapd_hw_modes
array of bands got an empty entry for that with NUM_HOSTAPD_MODES as the
mode. This resulted in various issues, e.g., with fst_hw_mode_to_band()
hitting a WPA_ASSERT(0).
Fix this by filtering out unsupported bands from the internal data
structures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Setting of the PN for the receive SA failed because the SCI wasn't
provided. Fix this by adding the needed attribute to the command.
Signed-off-by: Ze Gan <ganze718@gmail.com>
Now that we no longer leave build artifacts outside the build folder, we
can clean up the gitignore a bit. Also move more things to per-folder
files that we mostly had already anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If kernel advertises a band with channels < 2.4 GHz
hostapd/wpa_supplicant gets confused and assumes this is an IEEE
802.11b, corrupting the real IEEE 802.11b band info.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Unless debugging.
wpa_supplicant will log it failed to initialized the driver for the
interface anyway so this just silences some noise for users.
Signed-off-by: Roy Marples <roy@marples.name>
Add support to receive and process MSCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Use the "tmp_disallow" name more consistently so that both the core
wpa_supplicant functionality (struct wpa_bss_tmp_disallowed) and the
wpa_driver_ops callback have more similar names.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The NL80211_ATTR_VLAN_ID attribute expects non-zero values, but vlan_id
with value 0 has been set in VLAN offload case. Due to this, station
connection failure is observed if the driver advertises VLAN_OFFLOAD
support:
nl80211: NL80211_ATTR_STA_VLAN (addr=8c:fd:f0:22:19:15 ifname=wlan0
vlan_id=0) failed: -34 (Result not representable)
wlan0: STA 8c:fd:f0:22:19:15 IEEE 802.11: could not bind the STA
entry to vlan_id=0
Fix this by setting only non-zero values.
Fixes: 0f903f37dc ("nl80211: VLAN offload support")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Check if nl80211 control port TX status is available in the kernel and
enable control port TX if so. With this feature, nl80211 control path is
able to provide the same feature set as nl80211 (management) + AF_PACKET
socket (control) before.
For debugging and testing, this can explicitly be disabled with
the driver parameter control_port_ap=0.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The kernel commit "mac80211: support control port TX status reporting"
seems to be delivering the TX status events for EAPOL frames over
control port using NL80211_CMD_FRAME_TX_STATUS due to incorrect check on
whether the frame is a Management or Data frame. Use the pending cookie
value from EAPOL TX operation to detect this incorrect behavior and
redirect the event internally to allow it to be used to get full TX
control port functionality available for AP mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow custom ack handler to be registered and use the ext ack handler
for TX control port to fetch the cookie information. If these cookies
are not supported by the current kernel, a value of 0 is returned.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
In order to retransmit faster in AP mode, hostapd can handle TX status
notifications. When using nl80211, this is currently only possible with
socket control messages. Add support for receiving such events directly
over nl80211 and detecting, if this feature is supported.
This finally allows for a clean separation between management/control
path (over nl80211) and in-kernel data path.
A follow up commit enables the feature in AP mode.
Control port TX status contains the original frame content for matching
with the current hostapd code. Furthermore, a cookie is included, which
allows for matching against outstanding cookies in the future. This
commit only prints the cookie value for debugging purposes on TX status
receive.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This is a preliminary patch for using extack cookies for TX control port
handling. Custom ack handler arguments for send_and_recv() and friends
is introduced therefore. This commit does not actually use the provided
values, i.e., that will be added in a separate commit.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Read mode specific HE 6 GHz capability from phy info. This is needed
for futher user config validation and IE construction.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Add support for missing driver AKM capability flags from the list of
RSN_AUTH_KEY_MGMT_* flags and make these available through the
'GET_CAPABILITY key_mgmt' control interface command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant registered to process the Radio Measurement Request
frames unconditionally. This would prevent other location based
applications from handling these frames. Enable such a use case by
allowing wpa_supplicant to be configured not to register to process
these frames. This can now be done by adding "no_rrm=1" to the
driver_param configuration parameter.
In addition, wpa_driver_nl80211_init() does not have the provision to
take driver_params. Hence, resubscribe again with cfg80211 when this
driver parameter "no_rrm=1" is set after the initial setup steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit dd74ddd0df ("nl80211: Handle AKM suite selectors for AP
configuration") added warning log message "nl80211: Not enough room for
all AKM suites (num_suites=X > NL80211_MAX_NR_AKM_SUITES)" which in some
cases fills logs every 3 seconds, so fix this by increasing the log
message level to debug.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Ref: https://patchwork.ozlabs.org/project/openwrt/patch/20200504130757.12736-1-ynezz@true.cz/#2429246
Fixes: dd74ddd0df ("nl80211: Handle AKM suite selectors for AP configuration")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Linux bridging code does not allow a station mode WLAN interface in a
bridge and this prevents the AP mode scan workaround from working if the
AP interface is in a bridge and scanning can be only done by moving to
STA mode. Extend this workaround to remove the interface from the bridge
temporarily for the duration of the scan, i.e., for the same duration as
the interface needs to be moved into the station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When hostapd is started without beaconing (start_disabled=1), Public
Action frame transmission command through nl80211 needs to allow
offchannel operations regardless of the operating channel configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The driver can advertise supported AKMs per wiphy and/or per interface.
Populate per interface supported AKMs based on the driver advertisement
in the following order of preference:
1. AKM suites advertised by NL80211_ATTR_IFTYPE_AKM_SUITES
2. AKM suites advertised by NL80211_ATTR_AKM_SUITES
If neither of these is available:
3. AKMs support is assumed as per legacy behavior.
In addition, extend other driver interface wrappers to set the
per-interface values based on the global capability indication.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Since this functionality was not used for anything in practice, it is
easier to simply remove this functionality completely to avoid potential
conflicts in using the kernel tree upstream commit ab4dfa20534e
("cfg80211: Allow drivers to advertise supported AKM suites").
This is practically reverting the commit 8ec7c99ee4 ("nl80211: Fetch
supported AKM list from the driver").
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Convert driver indications to internal events to allow invalid Beacon
frames to be reported to the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update frame processing registration for DPP Public Action frames to
include multicast reception when in DPP listen mode and the driver
indicates support for this type of explicit request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This has no changes to the function itself, i.e., it is just moved to a
location that is above the first caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
drv->eapol_sock is used only for receiving EAPOL frames in AP mode, so
it is not needed when using control port for EAPOL frame RX.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since this nl80211 mechanism for sending EAPOL frames does not currently
support TX status notification, disable it by default of AP mode where
the Authenticator state machine uses those notifications to optimize
retransmission. The control port TX can be enabled for AP mode with
driver param control_port_ap=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use and/or set socker owner where necessary to allow EAPOL frames to be
received using the nl80211 control port. This is done when the driver
indicates support for the control port without previous hardcoded
reception of RSN preauth frames.
Use methods which set or use the connection owner nl_sock * where
necessary. Initial operations need to register with the SOCKET_OWNER
attribute set (e.g., connect for STA mode). Final operations need to use
the socket which holds the owner attribute (e.g., disconnect for STA
mode).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This commit creates a connect nl_sock * for every bss unconditionally.
It is used in the next commit for nl80211 control port RX.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
nl80211 control port event handling previously did not differentiate
between EAPOL and RSN preauth ethertypes. Add checking of the ethertype
and report unexpected frames (only EAPOL frames are supposed to be
delivered through this path).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This is needed since the initial implementation of the control port
mechanism in the kernel mixed in RSN pre-authentication ethertype
unconditionally (and IMHO, incorrectly) into the control port.
Signed-off-by: Jouni Malinen <j@w1.fi>
The only l2_packet use within this file was removed by commit
d12dab4c6f ("nl80211: Use non-receiving socket for EAPOL TX").
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.
There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
The new driver param full_ap_client_state=0 can be used to test
functionality with the driver capability for full AP client state being
forced to be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drivers that trigger roaming need to know the lifetime and reauth
threshold time of configured PMKSA so that they can trigger full
authentication to avoid unnecessary disconnection. To support this, send
dot11RSNAConfigPMKLifetime and dot11RSNAConfigPMKReauthThreshold values
configured in wpa_supplicant to the driver while configuring a PMKSA.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
Addition of chan_2ghz_or_5ghz_to_freq() broke 60 GHz ACS, because it
assumes reported ACS channel is on either 2.4 or 5 GHz band. Fix this
by converting chan_2ghz_or_5ghz_to_freq() to a more generic
chan_to_freq(). The new function uses hw_mode to support 60 GHz.
Fixes: 41cac481a8 ("ACS: Use frequency params in ACS (offload) completed event interface")
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
If the kernel rtm_newlink or rtm_dellink send the maximum length of
ifname (IFNAMSIZ), the event handlers in
wpa_driver_nl80211_event_rtm_addlink() and
wpa_driver_nl80211_event_rtm_dellink() did not copy the IFLA_IFNAME
value. Because the RTA_PAYLOAD (IFLA_IFNAME) length already includes the
NULL termination, that equals the IFNAMSIZ.
Fix the condition when IFNAME reach maximum size.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
Add key configuration parameters needed to support Extended Key ID with
pairwise keys. Add a driver capability flag to indicate support forusing
this.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
KEY_FLAG_MODIFY was initial added for the planned Extended Key ID
support with commit a919a26035 ("Introduce and add key_flag") and then
removed with commit 82eaa3e688 ("Remove the not yet needed
KEY_FLAG_MODIFY") to simplify commit e9e69221c1 ("Validity checking
function for key_flag API").
Add it again and update check_key_flag() accordingly.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The actual TX status (whether ACK frame was received) was not included
in the debug log in AP mode. Add that for all cases. In addition, add
some more details in the debug log to make the log more helpful in
debugging issues related to frame delivery.
Signed-off-by: Jouni Malinen <j@w1.fi>
The return value from nl80211_send_monitor() is not suitable for use
with strerror(). Furthermore, nl80211_send_monitor() itself is printing
out a more detailed error reason.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_and_recv_msgs() returns a negative number as the error code and
that needs to be negated for strerror().
Fixes: 8759e9116a ("nl80211: Control port over nl80211 helpers")
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_tdls_set_key() did set the key_id to -1 to avoid a useless
NL80211_CMD_SET_KEY call that the updated nl80211 driver no longer
carries out. Remove the no longer required workaround.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Migrate nl80211 driver to key_flag API and add additional sanity checks.
I'm still not sure why we install unicast WEP keys also as default
unicast keys. Based on how I understand how mac80211 handles that it
should be pointless. I just stuck to how we do things prior to the patch
for WEP keys to not break anything. After all other drivers may need it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Always report an error when NL80211_CMD_SET_KEY can't set a key to
default.
The old ioctl-based design used a single command to add, set, and delete
a key and had to ignore ENOENT for key deletions. It looks like that
special handling was also ported for NL80211_CMD_NEW_KEY and
NL80211_CMD_SET_KEY instead only for NL80211_CMD_DEL_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Calling NL80211_CMD_NEW_KEY with NL80211_KEY_DEFAULT_TYPES attributes is
pointless. The information is not expected and therefore the kernel
never forwards it to the drivers. That attribute is used with
NL80211_CMD_SET_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Allow to abort key installations with different error codes and fix one
misleading return code.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Turns out we are sometime providing a seq when deleting the key. Since
that makes no sense on key deletion let's stop forwarding that to the
driver at least.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
There is no support for using the control port for sending out EAPOL
frames through privsep yet, so mask out this capability to fall back to
the l2_packet based design.
Signed-off-by: Jouni Malinen <j@w1.fi>
To support PASN authentication flow, where Authentication frames are
sent by wpa_supplicant using the send_mlme() callback, modify the logic
to also send EVENT_TX_STATUS for Authentication frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.
hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If the driver requires external SAE authentication, it would result in
registration for all Authentication frames, so even non-SAE
Authentication frames might be forwarded to user space instead of being
handled internally. Fix this by using a more strict match pattern,
limiting the registration to the SAE authentication algorithm only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a new capability flag based on the nl80211 feature advertisement and
start using the new default key type for Beacon protection. This enables
AP mode functionality to allow Beacon protection to be enabled. This is
also enabling the previously added ap_pmf_beacon_protection_* hwsim test
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The CAN_REPLACE_PTK0 flag provided by nl80211 can be used to detect if
the card/driver is explicitly indicating capability to rekey STA PTK
keys using only keyid 0 correctly.
Check if the card/driver supports it and make the status available as a
driver flag.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
nla_nest_start() might fail, so need to check its return value similarly
to all the other callers.
Fixes: a84bf44388 ("HE: Send the AP's OBSS PD settings to the kernel")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously only couple of AKM suite selectors were converted into
NL80211_ATTR_AKM_SUITES. Add rest of the AKM suites here. However, since
the current kernel interface has a very small limit
(NL80211_MAX_NR_AKM_SUITES = 2), add the attribute only when no more
than that limit entries are included. cfg80211 would reject the command
with any more entries listed.
This needs to be extended in cfg80211/nl80211 in a backwards compatible
manner, so this seems to be the best that can be done for now in user
space. Many drivers do not use this attribute, so must not reject the
configuration completely when larger number of AKM suites is configured.
Such cases may not work properly with drivers that depend on
NL80211_ATTR_AKM_SUITES value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to work around a missing attribute that would cause
cfg80211 to reject some nl80211 commands (e.g.,
NL80211_ATTR_VENDOR_DATA) with new kernel versions that enforce netlink
attribute policy validation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.
Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <j@w1.fi>
A driver supports FT if it either supports SME or the
NL80211_CMD_UPDATE_FT_IES command. When selecting AKM suites,
wpa_supplicant currently doesn't take into account whether or not either
of those conditions are met. This can cause association failures, e.g.,
when an AP supports both WPA-EAP and FT-EAP but the driver doesn't
support FT (wpa_supplicant will decide to do FT-EAP since it is unaware
the driver doesn't support it). This change allows an FT suite to be
selected only when the driver also supports FT.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The internal WMM AC parameters use just the exponent of the CW value,
while nl80211 reports the full CW value. This led to completely bogus
CWmin/CWmax values in the WMM IE when a regulatory limit was present.
Fix this by converting the value to the exponent before passing it on.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nl80211 uses a different queue mapping from hostap, so AC indexes need
to be converted.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The size of a single route(4) message cannot be derived from
either the size of the AF_INET or AF_INET6 routing tables.
Both could be empty or very large.
As such revert back to a buffer size of 2048 which mirrors
other programs which parse the routing socket.
Signed-off-by: Roy Marples <roy@marples.name>
Now that both hostapd and wpa_supplicant react to interface flag
changes, there is no need to set or remove IFF_UP.
It should be an administrative flag only.
Signed-off-by: Roy Marples <roy@marples.name>
There is little point in having both and it brings interface
addition/removal and IFF_UP notifications to hostapd.
Signed-off-by: Roy Marples <roy@marples.name>
When external authentication is used, the station send mlme frame (auth)
to the driver may not be able to get the frequency (bss->freq) after
hostap.git commit b6f8b5a9 ("nl80211: Update freq only when CSA
completes"). Use the assoc_freq to send the MLME frame when SAE external
authentication is used to avoid this issue.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
Update the documentation with values to be sent for seg0 and seg1 fields
in external ACS result event for 20 MHz, 40 MHz, 80 MHz, 160 MHz, and
80+80 MHz channels. These values match the changes done to definitions
of seg0 and seg1 fields in the IEEE 802.11 standard.
This vendor command had not previously been documented in this level of
detail and had not actually been used for the only case that could have
two different interpretation (160 MHz) based on which version of IEEE
802.11 standard is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This is the function that actually uses the parameters, so pass the full
parameter struct to it instead of hiding the struct from it in the
simple wrapper.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add indication for driver VLAN offload capability and configuration of
the VLAN ID to the driver.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This makes it more convenient to add, remove, and modify the parameters
without always having to update every single driver_*.c implementation
of this callback function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Correct the check for presence of
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL attribute before using it
while processing acs_result event.
Fixes: 857d94225a ("Extend offloaded ACS QCA vendor command to support VHT")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for testing purposes to allow wpa_supplicant and hostapd
functionality to be tested both with and without using the nl80211
control port which is by default used whenever supported by the driver.
control_port=0 driver parameter will prevent that from happening.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows EAPOL frames to be received over the separate controlled
port once rest of the driver interface is ready for this. By itself,
this commit does not actually change behavior since cfg80211 will not be
delivering these events without them being explicitly requested.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
In order to correctly encrypt rekeying frames, wpa_supplicant now checks
if a PTK is currently installed and sets the corresponding encrypt
option for tx_control_port().
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Linux kernel v4.17 added the ability to request sending controlled port
frames (e.g., IEEE 802.1X controlled port EAPOL frames) via nl80211
instead of a normal network socket. Doing this provides the device
driver with ordering information between the control port frames and the
installation of keys. This empowers it to avoid race conditions between,
for example, PTK replacement and the sending of frame 4 of the 4-way
rekeying handshake in an RSNA. The key difference between the specific
control port and normal socket send is that the device driver will
certainly get any EAPOL frames comprising a 4-way handshake before it
gets the key installation call for the derived key. By flushing its TX
buffers it can then ensure that no pending EAPOL frames are
inadvertently encrypted with a key that the peer will not yet have
installed.
Add a CONTROL_PORT flag to the hostap driver API to report driver
capability for using a separate control port for EAPOL frames. This
operation is exactly like an Ethernet send except for the extra ordering
information it provides for device drivers. The nl80211 driver is
updated to support this operation when the device reports support for
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211. Also add a driver op
tx_control_port() for request a frame to be sent over the controlled
port.
Signed-off-by: Brendan Jackman <brendan.jackman@bluwireless.co.uk>
This was used only for FT RRB sending with driver_test.c and
driver_test.c was removed more than five years ago, so there is no point
in continuing to maintain this driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since NL80211_CMD_FRAME does not allow encryption to be disabled for the
frame, add a monitor interface temporarily for cases where this type of
no-encrypt frames are to be sent. The temporary monitor interface is
removed immediately after sending the frame.
This is testing functionality (only in CONFIG_TESTING_OPTIONS=y builds)
that is used for PMF testing where the AP can use this to inject an
unprotected Robust Management frame (mainly, Deauthentication or
Disassociation frame) even in cases where PMF has been negotiated for
the association.
Signed-off-by: Jouni Malinen <j@w1.fi>
I saw a case where the kernel's cfg80211 rejected hostapd's attempt to
send a neighbor report response because nl80211 flagged the frame as
offchannel-OK, but kernel rejects because channel was 100 (DFS) and so
kernel failed thinking it was constrained by DFS/CAC requirements that
do not allow the operating channel to be left (at least in FCC).
Don't set the packet as off-channel OK if we are transmitting on the
current operating channel of an AP to avoid such issues with
transmission of Action frames.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This is to match the NL80211_CMD_ACTION renaming to NL80211_CMD_FRAME
that happened long time ago. This command can be used with any IEEE
802.11 frame and it should not be implied to be limited to Action
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace a separate cookie_out pointer argument with save_cookie boolean
since drv->send_action_cookie is the only longer term storage place for
the cookies. Merge all nl80211_send_frame_cmd() callers within
wpa_driver_nl80211_send_mlme() to use a single shared call to simplify
the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge this function into wpa_driver_nl80211_send_mlme() that is now the
only caller for the previously shared helper function. This is a step
towards cleaning up the overly complex code path for sending Management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the previous users have now been converted to using send_mlme() so
this unused send_frame() callback can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows send_mlme() to be used to replace send_frame() for the test
cases where unencrypted Deauthentication/Disassociation frames need to
be sent out even when using PMF for the association. This is currently
supported only when monitor interface is used for AP mode management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Call nl80211_send_monitor() directly instead of going through
wpa_driver_nl80211_send_frame() for the case where monitor interface is
used for AP mode management purposes. drv->use_monitor has to be 1 in
this code path, so wpa_driver_nl80211_send_frame() was calling
nl80211_send_monitor() unconditionally for this code path and that extra
function call can be removed here to simplify the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Netlink dump message may be interrupted if an internal inconsistency is
detected in the kernel code. This can happen, e.g., if a Beacon frame
from the current AP is received while NL80211_CMD_GET_SCAN is used to
fetch scan results. Previously, such cases would end up not reporting an
error and that could result in processing partial data.
Modify this by detecting this special interruption case and converting
it to an error. For the NL80211_CMD_GET_SCAN, try again up to 10 times
to get the full response. For other commands (which are not yet known to
fail in similar manner frequently), report an error to the caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
libnl functions return a library specific error value in libnl 2.0 and
newer. errno is not necessarily valid in all error cases and strerror()
for the returned value is not valid either.
Use nl_geterror() to get the correct error string from the returned
error code.
Signed-off-by: Jouni Malinen <j@w1.fi>
libnl functions return a library specific error value. errno is not
necessarily valid in all error cases and strerror() for the returned
value is not valid either.
Use nl_geterror() to get the correct error string from the returned
error code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This simplifies code by not having to maintain and come up with new
backwards compatibility wrappers for a library release from 12 years
ago.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add function that returns whether WoWLAN has been enabled for the device
or not.
Signed-off-by: Alfonso Sanchez-Beato <alfonso.sanchez-beato@canonical.com>
Support for dynamic VLANs depends on the Linux bridge ioctls.
Add this dependency explicitely to drivers make files.
This fixes build for minimal hostapd configs such as:
CONFIG_DRIVER_WIRED=y
CONFIG_FULL_DYNAMIC_VLAN=y
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Normally nl80211 driver will attempt to strictly control what bridge
given interface is put in. It'll attempt to remove it from an existing
bridge if it doesn't match the configured one. If it's not in a bridge
it'll try to put it into one. If any of this fails then hostapd will
bail out and not set up the BSS at all.
Arguably that's reasonable since it allows to set the BSS up coherently
with regard to EAPOL handling as well as allows extra interactions with
things like FDB. However, not all hostapd drivers interact with bridge=
the same way. One example is atheros. Therefore it's not clear what the
desired behavior should be if consistency across drivers is considered.
There's a case where one might want to use a non-native Linux bridge,
e.g., openvswitch, in which case regular ioctls won't work to put an
interface into a bridge, or figure out what bridge an interface is in.
The underlying wireless driver can still be an ordinary nl80211 driver.
This change relaxes the bridge setup failure so that hostapd still
starts even if it fails to add an interface into a configured bridge
name. It still sets up all the necessary sockets (including the
configured bridge=) so EAPOL handling should work fine. This then leaves
it to the system integrator to manage wireless interface as bridge ports
and possibly fdb hints too.
Signed-off-by: Michal Kazior <michal@plume.com>
It was possible for the driver to advertise support for channels that
are not found from wpa_supplicant frequency-to-channel mapping (e.g.,
channel 182 at 5910 MHz) and that resulted in not initializing the
channel number information. Fix this by explicitly clearing the full
struct hostapd_channel_data buffer before parsing the information into
it from the driver.
This avoids some conditional jumps that could have dependent on
uninitialized values.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace channel fields with frequency fields in ACS completed event
interface from the driver layer. Use
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY attributes if the driver
includes them in the QCA_NL80211_VENDOR_SUBCMD_DO_ACS event, otherwise
use QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL attributes to maintain
backwards compatibility with old drivers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add EDMG bandwidth to CHANWIDTH_ defines.
Update API ieee80211_freq_to_channel_ext() to support EDMG bandwidth
for EDMG channels.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Clean up do_acs interface to not pass ch_list to drivers as the same
information is available in freq_list. The channel numbers are
duplicated between 2.4 GHz and 5 GHz bands and the 6 GHz band. So, use
the QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST to populate only 2.4 GHz and 5 GHz
channels to ensure backwards compatibility with old drivers which do not
have support to decode the newer QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This array can be freed either from the scan parameters or from
clearing the MAC address randomization parameters from the
wpa_supplicant struct. To make this ownership more clear, we have
each struct own its own copy of the parameters.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
SUITE_B_192 AKM capability was indicated for all devices using the
nl80211 driver (without the QCA vendor specific AKM capability
indication). However, some devices can't handle Suite B 192 due to
insufficient ciphers supported. Add a check for CCMP-256 or GCMP-256
cipher support and only indicate SUITE_B_192 capability when such cipher
is supported. This allows compiling with CONFIG_SUITEB192 and still get
proper response to the 'GET_CAPABILITY key_mgmt' command. Under Android
it can also serve as a dynamic way for HAL to query platform for
WPA3-Enterprise 192-bit support.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
Addi STA node details in AP through QCA vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE vendor when processing FT
protocol roaming.
Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
In the SME-in-driver case, wpa_supplicant used only the selected SAE
auth_alg value as the trigger for enabling external authentication
support for SAE. This prevented the driver from falling back to full SAE
authentication if PMKSA caching was attempted (Open auth_alg selected)
and the cached PMKID had been dropped.
Enable external auth based on SAE/FT-SAE key_mgmt, rather than doing
this based on SAE auth_alg, so that the driver can go through full SAE
authentication in cases where PMKSA caching is attempted and it fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11ay defines Enhanced Directional Multi-Gigabit (EDMG) STA and
AP which allow channel bonding of 2 channels and more.
nl80211 provides the driver's EDMG capabilities from the kernel
using two new attributes:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represents the channel bandwidth
configurations supported by the driver.
The driver's EDMG capabilities are stored inside struct hostapd_hw_modes.
As part of the connect request and starting AP, EDMG parameters are
passed as part of struct hostapd_freq_params.
The EDMG parameters are sent to the kernel by using two new attributes:
NL80211_ATTR_WIPHY_EDMG_CHANNEL and NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
which specify channel and bandwidth configuration for the driver to use.
This implementation is limited to CB2 (channel bonding of 2 channels)
and the bonded channels must be adjacent.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Linux 2.6.32 (December 2009) introduced alternate netlink messages
for setting and installing keys, deprecating the older ones.
To allow hostapd/wpa_supplicant to use new features only provided via
the new API this patch migrates all netlink messages to the current ones.
Since the nl80211 driver was sometimes already using the new format this
is only unifying the netlink API usage and not changing the minimal
kernel requirement.
The following netlink attributes have been retired for key installs:
NL80211_ATTR_KEY_DATA
NL80211_ATTR_KEY_TYPE
NL80211_ATTR_KEY_SEQ
NL80211_ATTR_KEY_IDX
NL80211_ATTR_KEY_CIPHER
NL80211_ATTR_KEY_DEFAULT
NL80211_ATTR_KEY_DEFAULT_MGMT
NL80211_ATTR_KEY_DEFAULT_TYPES
And replaced by the following attributes nested in NL80211_ATTR_KEY:
NL80211_KEY_DATA
NL80211_KEY_TYPE
NL80211_KEY_SEQ
NL80211_KEY_IDX
NL80211_KEY_CIPHER
NL80211_KEY_DEFAULT
NL80211_KEY_DEFAULT_MGMT
NL80211_KEY_DEFAULT_TYPES
When getting Michael MIC failure notifications or querying a key
sequence number the kernel continues to use the old attributes:
NL80211_ATTR_KEY_TYPE
NL80211_ATTR_KEY_SEQ
NL80211_ATTR_KEY_IDX
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
hostapd is only interested in RTM_IEEE80211.
wpa_supplicant is only interested in RTM_IEEE80211, RTM_IFINFO and
RTM_IFANNOUNCE.
This supports the NetBSD RO_MSGFILTER interface and the alternative
DragonFlyBSD/OpenBSD interface ROUTE_MSGFILTER.
Signed-off-by: Roy Marples <roy@marples.name>
This allows us to send the OBSS PD settings to the kernel, such that the
driver can propagate them to the hardware/firmware.
Signed-off-by: John Crispin <john@phrozen.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update Connection Params is intended for drivers that implement
internal SME and expect these updated connection params from
wpa_supplicant. Do not send this request for the drivers using
SME from wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
HE (802.11ax) is also supported on 2.4 GHz. And the 2.4 GHz band isn't
supposed to use VHT operations. Some codepaths in wpa_supplicant will
therefore not initialize the freq->bandwidth or the freq->center_freq1/2
members. As a result, the nl80211_put_freq_params() will directly return
an error (-1) or the kernel will return an error due to the invalid
channel definition.
Instead, the channel definitions should be created based on the actual
HT/VHT/none information on 2.4 GHz.
Fixes: ad9a1bfe78 ("nl80211: Share VHT channel configuration for HE")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
qca_wlan_vendor_attr_roam_subcmd is an enum associated with the
attribute QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. It represents different
sub command values and these are not the attributes. Hence, rename the
enum to qca_wlan_vendor_roaming_subcmd. Accordingly, the members of this
enum are also renamed to suite the usage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit d896874f86 ("nl80211: Indicate 802.1X 4-way handshake offload
in connect") used the req_key_mgmt_offload flag to indicate to the
driver that it should offload the 802.1X handshake. However, this field
was existing and used for a different offload API. This causes
wpa_supplicant to send a connect request without the WANT_1X_HS flag and
the subsequent set-pmk is rejected causing the connection to fail. Fix
that by introducing a new flag req_handshake_offload so the offloads are
no longer entangled.
Fixes: d896874f86 ("nl80211: Indicate 802.1X 4-way handshake offload in connect")
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
The relevant flags were only added in Linux 4.6, so we shouldn't
complain because they're missing. Also, they're always missing if a
device is being removed (e.g., 'iw dev wlan0 del', or if the device is
in the process of resetting itself). So kill those 2 birds with 1 stone:
if we can't find the file, just silently skip it.
Also, we probably should *actually* propagate the error if we had a
write failure.
Signed-off-by: Brian Norris <briannorris@chromium.org>
The AP mode fix for removing NL80211_ATTR_STA_WME from
NL80211_CMD_SET_STATION did not consider the TDLS case and that resulted
in incorrectly removing WMM parameters from TDLS STA entry updates. Fix
this by considering the WPA_STA_TDLS_PEER flag similarly to the other
update parameters.
Fixes: 6d14b98fc6 ("nl80211: Do not add WMM parameters when updating an existing STA entry")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mesh points can partially support HE features (when requiring no
controlling STA/AP) as long as hardware supports it. The kernel just
requires support for HE mesh and wpa_supplicant can forward the peer
capabilities to the kernel for further processing.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The HE capabilities are no longer per PHY but per iftype on this
specific PHY. It is therefore no longer enough to just parse the AP
capabilities.
The he_capabilities are now duplicated to store all information for
IEEE80211_MODE_* which hostap cares about. The nl80211 driver fills in
this information when the iftype supports HE. The rest of the code still
only uses the IEEE80211_HE_AP portion but can be extended later to also
use other HE capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
This command/event interface can be used by SME based host drivers that
rely on user space (hostapd/wpa_supplicant) for DH IE
processing/generation. This interface facilitates the OWE connection
with host drivers by offloading DH IE processing to the user space
(hostapd/wpa_supplicant).
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A driver that uses internal AP SME may need to be able to use the
external_auth status operation in station mode, so do not skip this
solely based on drv->device_ap_sme; instead, use that condition only
when operating in AP mode.
Fix external_auth status in non SME case.
Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
In previous versions the device was allowed by ETSI to implement
802.11 channel access mechanism based on a set of priority classes
which are taken from 802.11. According of the new standard there
might be some exceptions which require ETSI countries to follow
more restrictive rules. In such a case the AP's wmm IE need to
comply with ETSI limitation. To be able to do so the regulatory
domain passes the new limitation values if needed.
Implement this, by storing it and use it to calculate the new
WMM parameters.
This commit adds determination of regulator limitations to
NL80211_CMD_GET_WIPHY processing so that the information is available
for upper layer implementation to use later when constructing WMM
element.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add support for injecting frames to a given mesh peer, bypassing the
mpath table lookup using PROBE_MESH_LINK command. This helps to send
data frames over unexercised direct mesh path, which is not selected as
next_hop node. This can be helpful in measuring link metrics.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
