Instead of building in the source tree, put most object
files into the build/ folder at the root, and put each
thing that's being built into a separate folder.
This then allows us to build hostapd and wpa_supplicant
(or other combinations) without "make clean" inbetween.
For the tests keep the objects in place for now (and to
do that, add the build rule) so that we don't have to
rewrite all of that with $(call BUILDOBJS,...) which is
just noise there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will make it easier to split out the handling in
a proper way, and handle common cflags/dependencies.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up in a more common fashion as well, initially for ../src/.
Also add $(Q) to the clean target in src/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some things are used by most of the binaries, pull them
into a common rule fragment that we can use properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When testing SAE reflection, the incoming commit may have the H2E status
code (126) or SAE-PK (127), but the test code in the AP was always
sending back status code 0. The STA would then reject the commit
response due to expecting H2E/SAE-PK status code.
Just reflect the incoming status code so the commit can be rejected
based on the SAE contents regardless of which variant of SAE was used.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
If there is no matching interface given, but interface matching is
enabled, all interfaces on the system will try to be initialized. Non
wireless interfaces will fail and the loopback device will be one of
these, so just log a diagnostic rather than an error.
Signed-off-by: Roy Marples <roy@marples.name>
Instead, log a diagnostic so that noise to the user is reduced. This is
expected behavior with driver interfaces that do not report supported
operating modes/classes.
Signed-off-by: Roy Marples <roy@marples.name>
Unless debugging.
wpa_supplicant will log it failed to initialized the driver for the
interface anyway so this just silences some noise for users.
Signed-off-by: Roy Marples <roy@marples.name>
This is needed for clearing previously set parameters in a similar
manner that was already available through the control interface
SET_NETWORK command.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Remove this part of the dbus_network test case since it would be causing
failures after wpa_supplicant is modified to accept empty strings
through D-Bus.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Teach wpa_supplicant to {de,}initialize bgscans when bgscan parameters
are set after initial connection.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Currently, wpa_config_set(), the function that sets wpa_supplicant
per-network properties, returns 1 when a property it attempts to set is
unchanged. Its global parallel, wpa_config_process_global(), doesn't do
this even though much of the code is very similar. Change this, and
several of the parser functions, to resemble the per-network parser and
setter functions.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
When network properties are updated via dbus, wpa_config_set() is used
to update the property in the wpa_ssid struct. If it returns 1, the
property was not changed and there's no need to perform any of the
update actions.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
D-Bus clients can call CreateInterface() once and use the resulting
Interface object to connect multiple times to different networks.
However, if the network interface gets added to a bridge, clients
currently have to remove the Interface object and create a new one.
Improve this by supporting the change of the BridgeIfname property of
an existing Interface object.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
This is useful to run monitor quickly:
./run-tests.py -t run_monitor -m mon:36,20,36,0:1,20,1,0
In such example we will get one PCAP for 36/20 and 1/20.
After execution, PCAP file is in the log directory, e.g.:
./logs/2019_11_11_13_36_24/run_monitor_mon_wlp3s0_wlp5s0.pcap
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This is mainly for standalone monitor in case we know and would like to
setup specific monitor configuration.
-m monitor:<chan>,<bw>, <cf1>, <cf2>:...
For example:
-m monitor:1,40,3,0
-m e4300:1,40,3,0:11,40,9,0
This also supports monitor with multiple interfaces (one pcap).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Before we have to kill an application we start in the thread - in most
cases using killall and sometimes kill other applicantions, e.g., tcpdump,
iper, iperf3, tshark.
With this patch we are able to stop/kill a single application/thread
instead, based on the pid file.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
In case we are using ssh MUX (which speed up a lot test execution) with
remotehost we could hit cases where ssh will hang up. This depends on
different ssh versions and remotehost implementation.
stderr as a tmpfile fixes this problem.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Add a new configuration parameter p2p_6ghz_disable=1 to disable P2P
operation in the 6 GHz band. This avoids additional delays caused by
scanning 6 GHz channels in p2p_find and p2p_join operations in the cases
where user doesn't want P2P connection in the 6 GHz band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Some legacy stations copy previously reserved RSN capability bits,
including OCVC, in (Re)Association Request frames from the AP's RSNE but
do not indicate MFP capability and/or do not send OCI in RSN handshakes.
This is causing connection failures with such erroneous STAs.
To improve interoperability with such legacy STAs allow a workaround OCV
mode to be enabled to ignore OCVC=1 from the STA if it does not follow
OCV requirements in the first protected exchange. This covers cases
where a STA claims to have OCV capability, but it does not negotiate use
of management frame protection or does not include OCI in EAPOL Key msg
2/4, FT Reassociation Request frame, or FILS (Re)Association Reqest.
The previous behavior with ocv=1 is maintained, i.e., misbehaving STAs
are not allowed to connect. When the new workaround mode is enabled with
ocv=2, the AP considers STA as OCV capable on below criteria
- STA indicates both OCV and MFP capability
- STA sends OCI during connection attempt in a protected frame
Enabling this workaround mode reduced OCV protection to some extend
since it allows misbehavior to go through. As such, this should be
enabled only if interoperability with misbehaving STAs is needed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Modify status code in FT Reassociation Response frame from
WLAN_STATUS_UNSPECIFIED_FAILURE to WLAN_STATUS_INVALID_FTE when replying
to an invalid OCI channel info (subelement of FTE) in FT Reassociation
Request frame.
Signed-off-by: Shaakir Mohamed <smohamed@codeaurora.org>
Generate a control interface event upon receipt of DPP Presence
Announcement frames. This allows external programs to instrument
wpa_supplicant with bootstrapping information on-demand.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
Generate a control interface event upon receipt of DPP Presence
Announcement frames. This allows external programs to instrument hostapd
with bootstrapping information on-demand.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
Define a control event with bootstrap id, frame source, frequency, and
chirp hash for receipt of Presence Announcement (chirp) frames.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
When a Presence Announcement frame is received, a check is done to
ensure an ongoing auth is not in progress (!hapd->dpp_auth). A new DPP
auth is then initialized, however, when setting global configurator
params for it, the hapd->dpp_auth pointer is used which was earlier
confirmed as NULL, causing a crash in dpp_set_configurator params when
the pointer is dereferenced.
This only occurs when there are global DPP configurator params to be set
and the peer has no overriding configurator params. If no global DPP
configurator params exist, the call to dpp_set_configurator exits early
and the problem is not observed.
Fix by using the newly init'ed DPP auth structure for setting global
DPP configurator params.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
ignore_broadcast_ssid is supported when using with the config
file. But it generates an error if you try to set it via the
DBus interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
DPP tech spec was modified to use v1(0) instead of v2(1) for the
OneAsymmetricKey in the Configurator backup structure to match the
description in RFC 5958 Section 2 which indicates v2 to be used when any
items tagged as version 2 are included. No such items are actually
included in this case, so v1 should be used instead.
Change OneAsymmetricKey generation to use v1(0) instead of v2(1) and
parsing to accept either version to be used. This is not backwards
compatible with the earlier implementation which requires v2(1) when
parsing the received value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check if the 2.4 GHz channel 6 is in the list of available channels
advertised by the driver before adding in to the chirping frequency
list. This fixes issues, e.g., with a 5 GHz only interface.
Signed-off-by: Disha Das <dishad@codeaurora.org>
The Query Response Length field was missing from GAS Initial Response
and GAS Comeback Response frames in the DPP specific code path from
hostaps GAS server. This resulted in invalid frames being used when the
DPP Config Response needed fragmentation. Fix this by adding the Query
Response Length fields into these frames.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Initiate SA Query for a WPS+MFP AP. STA flag checks for MFP added for
Association Request frames that use WPS IE without RSNE. This is needed
to avoid giving an opportunity to skip the protection against
disconnections when WPS is enabled.
Signed-off-by: Disha Das <dishad@codeaurora.org>
The per-interface P2P data freeing function did not cover this eloop
timeout that could potentially have been registered. Explicitly cancel
this timeout to make sure no references to freed memory can remain in
such a case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant_remove_iface() removes the P2P management interface from
the global interfaces list before calling wpa_supplicant_deinit_iface().
When wpas_p2p_group_remove() is called from
wpa_supplicant_deinit_iface(), the P2P group created on the calling
wpa_s was not getting cleared as the calling wpa_s is not in the list of
global->ifaces. This results in the P2P management interface being
removed without disconnecting the p2p_group created on it. This could
result in an illegal access of freed memory, e.g., when a pending eloop
task wpas_p2p_reconsider_moving_go() was triggered with the leftover ctx
pointer to the removed P2P interface instance.
Fix this by disconnecting the P2P group created on interface to be
deinitialized before deinitializing the interface.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
With the configuration defined in the global_op_class array, the
channels starting from 149 in the operating classes 128 and 130 were not
considered for P2P channel setup due to the non-continuous
incrementation of channel indexes. The other channels in these operating
classes were considered. Handle the channels from 149 to 161 in the
operating classes 128 and 130 for P2P channel setup by handling this
jump in the channel number incrementation.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
crypto_bignum_init_set() might fail in case of memory allocation
failures. These two cases within sswu() did not handle that properly,
i.e., a memory allocation failure could have resulted in dereferencing a
NULL pointer. Check the return value before proceeding to fix this.
Fixes: aeb022f8e5 ("SAE: Implement hash-to-element PT/PWE crypto routines")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
