Commit graph

605 commits

Author SHA1 Message Date
Jeffery Miller
c6f8af507e Add option to disable SAE key_mgmt without PMF
Add the `sae_check_mfp` global option to limit SAE when PMF will
not be selected for the connection.
With this option SAE is avoided when the hardware is not capable
of PMF due to missing ciphers.
With this option SAE is avoided on capable hardware when the AP
does not enable PMF.

Allows falling back to PSK on drivers with the
WPA_DRIVER_FLAGS_SAE capability but do not support the BIP cipher
necessary for PMF. This enables configurations that can fall back
to WPA-PSK and avoid problems associating with APs configured
with `sae_require_mfp=1`.

Useful when `pmf=1` and `sae_check_mfp=1` are enabled and networks
are configured with ieee80211w=3 (default) and key_mgmt="WPA-PSK SAE".
In this configuration if the device is unable to use PMF due to
lacking BIP group ciphers it will avoid SAE and fallback to
WPA-PSK for that connection.

Signed-off-by: Jeffery Miller <jefferymiller@google.com>
2022-11-05 17:48:17 +02:00
Matthew Wang
2e73394426 P2P: Discount current operating frequency when scanning new connection
When scanning for a new connection, we currently optimize by scanning
all frequencies only when our MCC capabilities will allow an additional
operating frequency, and scan only the existing operating frequencies
otherwise. This is problematic when there the current operating
frequency singularly accounts for one of the shared radio frequencies
because we should be able to switch operating frequencies without adding
to the channel count. Fix this.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2022-11-05 13:43:06 +02:00
Vinay Gannevaram
ea241cbe9d PASN: Rename struct wpas_pasn to pasn_data
struct wpas_pasn is common to both initiator and responder, so rename it
to pasn_data to avoid the "wpas_" prefix that could be seen as a
reference to wpa_supplicant (PASN initiator).

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 12:59:29 +02:00
Vinay Gannevaram
14b5ebce73 PASN: Add a common header file for initiator and responder
This is a step towards decoupling the PASN initiator and responder
implemenentation is decoupled from the wpa_s and hapd contexts and
moving to a common folder for better abstraction. Move the struct
wpas_pasn definition to a common file for initiator and responder. The
idea is to provide a library libpasn.so from PASN common code. Include
C++ compatibilty wrapper to extend libpasn.so support for modules using
cpp code base.

This library can be used in applications implementing protocols based on
the PASN handshake.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:52:15 +02:00
Vinay Gannevaram
af5eec3b37 PASN: Function handler to transmit Authentication frames
Introduce a function handler to transmit PASN Authentication frames to
the driver. This removes the wpa_s dependency from PASN functionality
for sending the frames.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:59 +02:00
Vinay Gannevaram
629bbc91b1 PASN: Remove dependency of wpa_ssid for initiator
Get ssid and derive required information for SAE and FILS tunneled PASN
authentication to remove struct wpa_ssid dependency for PASN initiator.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:59 +02:00
Vinay Gannevaram
0be131265a PASN: Remove wpa_s dependency for wpas_pasn_build_auth_1()
Obtain RSNXE capabilities from the driver flags as well and save them in
the wpas_pasn structure.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:59 +02:00
Vinay Gannevaram
086ccdc598 PASN: Remove wpa_s dependency for the functions processing RX frames
Remove wpa_s dependency for processing PASN M2 frame and preparing M3
frame. To hold the context of wpa_s when transmitting M3 frame, add cb
ctx.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:59 +02:00
Vinay Gannevaram
de4b73a36a PASN: Remove wpa_s dependency for FILS wrapped data
To avoid reuse without struct wpa_supplicant, add new parameters to
struct wpas_pasn for FILS.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:59 +02:00
Vinay Gannevaram
90bb73c518 PASN: Remove wpa_sm dependency to add an entry to PMKSA cache
Store PMKSA cache entry in wpas_pasn and remove wpa_sm dependency to add
an entry to PMKSA cache. This is a step towards allowing the PASN
implementation to be used outside the context of wpa_supplicant.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-11-04 00:41:56 +02:00
Veerendranath Jakkam
73f540b6a7 MLD STA: Fetch MLO association Link ID info to core wpa_supplicant
Fetch the MLO association Link ID info from the driver to the
wpa_supplicant instance of the corresponding MLD STA interface. This
info is needed when setting the MLO connection info to wpa_sm.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-10-31 12:07:41 +02:00
Jouni Malinen
e5d15e2254 EHT: Allow EHT to be disabled using disable_eht=1 in wpa_supplicant
This is similar to the previously added disable_ht/vht/he parameters.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-10-17 11:13:09 +03:00
Shivani Baranwal
7784964cbe MLD STA: Fetch MLO connection info into core wpa_supplicant
Add support to fetch MLO connection info from the driver to the
wpa_supplicant instance of corresponding MLD STA interface. In addition,
return true for BSSs associated with MLO links from wpa_bss_in_use() to
avoid getting them cleared from scan results.

Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
2022-09-15 05:55:40 +03:00
Veerendranath Jakkam
d1a7626ff9 SAE: Use correct SSID profile for SAE auth retries during external auth
Previously, wpa_supplicant was using the current SSID for building the
SAE authentication commit frame for retries during external
authentication. But the external authentication SSID can be different
from the current SSID. Fix this by using the correct SSID profile.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-09-13 05:53:05 +03:00
Veerendranath Jakkam
76793cbbca SAE: Make sure H2E PT is derived for external auth SSID profile
The driver's SME may choose a BSS of a different ESS (SSID) compared to
the current SSID and trigger external authentication. If the chosen SSID
is not associated/selected before by wpa_supplicant it won't have the
H2E PT derived. Make sure to derive PT for SSID indicated in the
external authentication request.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-09-13 05:10:17 +03:00
Vinay Gannevaram
74d894a2ea PASN: Offload handshake for multiple peers from the driver
This brings in the functionality to hold multiple peers and perform PASN
authentication with each peer at a time and send the PASN response to
the driver. PASN parameters such as AKMP and cipher suite are obtained
from the BSS information of the cached scan results. Also add
functionality to trigger deauthentication to the peer for which PASN
request with action PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT is
received.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-09-02 16:18:12 +03:00
Vinay Gannevaram
9391f71004 Add own MAC address in PASN supplicant start and deauthentication
The driver requests PASN authentication for a peer with a specified
source (own) MAC address. Use the specified own MAC address for PASN
operations. This is needed to allow random MAC addresses to be used.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-09-01 19:01:21 +03:00
Veerendranath Jakkam
5de45546d5 Add support to send multi AKM connect request when driver's SME in use
Add support to configure SAE, PSK, and PSK-SHA256 AKMs in connect
request when driver's SME in use. This is needed for implementing
WPA3-Personal transition mode correctly with any driver that handles
roaming internally.

Send additional AKMs configured in network block to driver based on
the maximum number of AKMs allowed by driver in connect request. Keep
first AKM in the list AKMs in the connect request as AKM selected by
wpa_supplicant to maintain backwards compatibility.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-08-26 17:54:12 +03:00
Veerendranath Jakkam
0ce1545dcb nl80211: Determine maximum number of supported AKMs
Use the recently added attribute to determine whether the kernel
supports a larger number of AKM suites in various commands.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-08-26 17:27:45 +03:00
Purushottam Kushwaha
ef4cd8e33c QoS: Use common classifier_mask for ipv4/ipv6
ipv4_params/ip6_params in type4_params maintains separate classifier
mask while type4_params already has a common classifier_mask. Lets
use the common classifier mask for both ipv4/ipv6 params and remove
the redundant params_mask in ipv4_params/ip6_params.

Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
2022-07-28 12:31:37 +03:00
Jouni Malinen
1ff9251a83 DPP3: Push button Configurator in wpa_supplicant
Extend DPP push button support in wpa_supplicant to allow the role of
the Configurator to be used. This provides similar functionality to the
way the DPP_PUSH_BUTTON command in hostapd worked when providing the
configuration parameters with that command (instead of building the
config object based on current AP configuration).

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-07-22 12:28:18 +03:00
Jouni Malinen
148de3e0dc DPP3: Private Peer Introduction protocol
Add a privacy protecting variant of the peer introduction protocol to
allow the station device to hide its Connector from 3rd parties. The new
wpa_supplicant network profile parameter dpp_connector_privacy=1 can be
used to select this alternative mechanism to the peer introduction
protocol added in the initial release of DPP.

It should be noted that the new variant does not work with older DPP APs
(i.e., requires support for release 3). As such, this new variant is
disabled by default.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-07-19 00:14:41 +03:00
Jouni Malinen
37bccfcab8 DPP3: Push button bootstrap mechanism
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-07-07 00:31:30 +03:00
Sreeramya Soratkal
4383528e01 P2P: Use weighted preferred channel list for channel selection
Previously, the driver could optionally (using QCA vendor command)
provide a preferred channel list to wpa_supplicant for channel selection
during the GO negotiation. Channel selection process can be more
efficient with the information of weights and flags of the preferred
channel list that can be provided by the driver. Use a weighted
preferred channel list provided by the driver for channel selection
during GO negotiation if such a list is available.

Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com>
2022-06-02 17:09:10 +03:00
Jouni Malinen
1004fb7ee4 tests: Testing functionality to discard DPP Public Action frames
This can be used to make sure wpa_supplicant does not process DPP
messages sent in Public Action frames when a test setup is targeting
DPP-over-TCP.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-05-24 23:30:39 +03:00
Ilan Peer
79dc7f6190 scan: Add option to disable 6 GHz collocated scanning
Add a parameter (non_coloc_6ghz=1) to the manual scan command to disable
6 GHz collocated scanning.

This option can be used to disable 6 GHz collocated scan logic. Note
that due to limitations on Probe Request frame transmissions on the 6
GHz band mandated in IEEE Std 802.11ax-2021 it is very likely that
non-PSC channels would be scanned passively and this can take a
significant amount of time.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2022-05-07 21:37:08 +03:00
Jouni Malinen
18c0ac8901 Provide information about the encryption status of received EAPOL frames
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.

Signed-off-by: Jouni Malinen <j@w1.fi>
2022-05-07 21:37:03 +03:00
Veerendranath Jakkam
696ad5c2d7 EHT: Indicate wifi_generation=7 in wpa_supplicant STATUS output
This adds wifi_generation=7 line to the STATUS output if the driver
reports (Re)Association Request frame and (Re)Association Response frame
information elements in the association or connection event with EHT
capability IEs.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-05-05 13:21:04 +03:00
Kuan-Chung Chen
734fa392f7 MBO: Check association disallowed in Beacon frames, if newer
When a station receives either a Beacon frame or a Probe Response frame
from an AP that contains an MBO element with the Association Disallowed
attribute, the station should prevent association to that AP. When using
passive scanning, it is possible for the scan results to contain the
latest information in the Beacon frame elements instead of the Probe
Response frame elements. That could result in using old information and
not noticing the AP having changed its state to disallowing new
associations.

Make it more likely to follow the AP's change to disallow associations
by checking the Beacon frame elements instead of Probe Response frame
elements if the scan results are known to contain newer information for
the Beacon frame.

Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
2022-04-24 12:12:21 +03:00
Jouni Malinen
6135a8a6aa Stop authentication attemps if AP does not disconnect us
It would have been possible for the authentication attemps to go into a
loop if the AP/Authenticator/authentication server were to believe EAP
authentication succeeded when the local conclusion in Supplicant was
failure. Avoid this by timing out authentication immediately on the
second consecutive EAP authentication failure.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-04-06 15:28:49 +03:00
Veerendranath Jakkam
b746cb28bc Add support for not transmitting EAPOL-Key group msg 2/2
To support the STA testbed role, the STA has to disable transmitting
EAPOL-Key group msg 2/2 of Group Key Handshake. Add test parameter to
disable sending EAPOL-Key group msg 2/2 of Group Key Handshake.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
2022-04-05 17:06:32 +03:00
Chaoli Zhou
077bce96f3 Set drv_max_acl_mac_addrs in wpa_supplicant AP mode
hostapd code will need this for offloading ACL to the driver.

Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
2022-03-24 20:53:50 +02:00
Jouni Malinen
eeb72e7c9a DPP: Extend DPP_PKEX_ADD ver=<1/2> to cover Responder role
Allow PKEX v1-only or v2-only behavior to be specific for the Responder
role. This is mainly for testing purposes.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-03-07 21:37:40 +02:00
Jouni Malinen
7a7f803a90 DPP: Stop offchannel frame TX wait on DPP_STOP_LISTEN in a corner case
The offchannel frame TX wait was stopped whenever processing
DPP_STOP_LISTEN in most cases. However, there was a corner case on the
Responder side where this operation was skipped after PKEX was completed
successful and the Authentication Request frame had not yet been
received from the Initiator.

While this does not normally cause any significant issue, this could
result in unexpected behavior especially in test cases that run multiple
DPP PKEX operations in a row since the start of a new TX operation might
get delayed while waiting for the previous TX-wait to complete.

This was found with the following test case sequence:
dpp_reconfig_retries dpp_pkex_alloc_fail

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-02-24 00:23:11 +02:00
Jouni Malinen
a6d157b6f6 DPP: Start a listen operation for GAS server if needed
Instead of depending on the TX-wait-response-time to be sufficient to
cover the full GAS exchange, start an ongoing listen operation on the
negotiation channel (if no such listen operation is already in place) to
allow the configuration exchange to take longer amount of time. This is
needed for cases where the conf=query is used to request Configurator
parameters from upper layers and that upper layer processing (e.g., user
interaction) takes significant amount of time.

Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
2022-02-04 00:23:19 +02:00
Nicolas Norvez
16b5ea9e91 Reject authentication start during BSS TM requests
After receiving a BSS Transition Management request,
wpa_supplicant_connect() will abort ongoing scans, which will cause scan
results to be reported. Since the reassociate bit is set, this will
trigger a connection attempt based on the aborted scan's scan results
and cancel the initial connection request. This often causes
wpa_supplicant to reassociate to the same AP it is currently associated
to instead of the AP it was asked to transition to.

Add a bss_trans_mgmt_in_progress flag to indicate that we're currently
transitioning to a different AP so that we don't initiate another
connection attempt based on the possibly received scan results from a
scan that was in progress at the time the BSS Transition Management
request was received.

This is the equivalent of commit 5ac977758d ("Reject authentication
start during explicit roam requests") for the roaming scenario.

Signed-off-by: Nicolas Norvez <norvez@chromium.org>
2022-01-11 17:57:38 +02:00
Damien Dejean
4262e6ca49 Move credential removal operations into helper functions
This allows the same functions to be used for both the control interface
and the D-Bus interface.

Signed-off-by: Damien Dejean <damiendejean@chromium.org>
2021-12-12 17:10:05 +02:00
Vinay Gannevaram
2b3e64a0fb Update ciphers to address GTK renewal failures while roaming
After roaming from WPA2-AP (group=CCMP) to WPA-AP (group=TKIP) using
driver-based SME and roaming trigger, GTK renewal failures are observed
for the currently associated WPA-AP because of group cipher mismatch,
resulting in deauthentication with the AP.

Update the group cipher and pairwise cipher values in wpa_sm from
association event received from the driver in case of SME offload to the
driver to address GTK renewal failures (and similar issues) that could
happen when the driver/firmware roams between APs with different
security profiles.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-10-06 21:13:19 +03:00
Veerendranath Jakkam
d144b7f34c DSCP: Add support to send DSCP Policy Query frame
Add support to send DSCP Policy Query frame using a new control
interface command DSCP_QUERY. This includes support for a wildcard DSCP
query and a DSCP query with a single Domain Name attribute.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-09-30 16:56:56 +03:00
Veerendranath Jakkam
c903257fb1 DSCP: Parse WFA Capabilities element in (Re)Association Response frame
Add support to parse WFA Capabilities element from the (Re)Association
Response frame. Also register a timeout for the station to wait before
sending a new DSCP query if requested by AP.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-09-29 17:18:48 +03:00
Veerendranath Jakkam
d57456c1ff DSCP: Allow DSCP Policy Response Action frame to be sent
Add support to prepare and send DSCP response action frame to the
connected AP in response to a new control interface command DSCP_RESP.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-09-29 17:01:34 +03:00
Veerendranath Jakkam
2033e318e6 DSCP: Parsing and processing of DSCP Policy Request frames
Add support to parse received DSCP Policy Request frames and send the
request details as control interface events.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-09-29 00:20:42 +03:00
Veerendranath Jakkam
fe2a44485e DSCP: DSCP policy capability configuration
The DSCP policy capability is disabled by default. The user frameworks
which have support for handling DSCP policy request messages need to
enable this capability explicitly to allow wpa_supplicant to advertise
the capability to the AP and allow the related frames to be processed.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-09-28 11:07:21 +03:00
Jouni Malinen
8471d940e3 Move pmf_in_use() into a more generic file
This function is not specific to GAS, so make it available throughout
wpa_supplicant without requiring CONFIG_GAS.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-09-28 11:07:21 +03:00
Hu Wang
ce267f4da9 P2P: DFS offload for the autonomous GO
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.

For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'

- Previous behavior: AP fallback to channel 100 using 20 MHz with
  "No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
  "VHT center channel 106 for 80 or 80+80 MHz bandwidth"

This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-09-07 17:40:25 +03:00
Vinita S. Maloo
e433d06dd5 Allow MSCS support to be disabled for testing purposes
"SET disable_mscs_support 1" can be used to disable indication of MSCS
support in the Extended Capabilities element for testing purposes. This
is also disabling addition of the MSCS element even if valid
configuration parameters had been configured.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2021-08-12 18:28:07 +03:00
Vinita S. Maloo
025f8ab52e SCS: Processing of SCS Response frames
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2021-08-12 18:28:07 +03:00
Vinita S. Maloo
b4e01ae929 Allow SCS supported to be disabled for testing purposes
"SET disable_scs_support 1" can be used to disable indication of SCS
support in the Extended Capabilities element for testing purposes.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2021-08-12 18:28:07 +03:00
Vinita S. Maloo
c005283c48 SCS: Sending of SCS Request frames
Add support to parse SCS control interface command and form the SCS
Request frame to be sent to SCS enabled AP.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2021-08-12 18:28:07 +03:00
Veerendranath Jakkam
80bcd7ecd1 FILS: Flush PMKSA entries on FILS connection failure
wpa_supplicant generates both a PMKSA cache entry and ERP keys upon
successful FILS connection and uses FILS authentication algorithm for
subsequent connections when either ERP keys or a PMKSA cache entry is
available.

In some cases, like AP/RADIUS server restart, both ERP keys and PMKSA
becomes invalid. But currently when an AP rejects an association,
wpa_supplicant marks only ERP keys as failed but not clearing PMKSA.

Since PMKSA is not cleared, consecutive connection attempts are still
happening with FILS authentication algorithm and connection attempts are
failing with the same association rejection again instead of trying to
recover from the state mismatch by deriving a new ERP key hierarchy.

Clear PMKSA entries as well on association rejection from an AP to allow
the following connection attempt to go with open authentication to
re-establish a valid ERP key hierarchy. Also, since clearing PMKSA
entries on unprotected (Re)Association Response frames could allow DoS
attack (reduce usability of PMKSA caching), clear PMKSA entries only
when ERP keys exists.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-07-14 21:20:17 +03:00
Vamsi Krishna
1d2118b509 Check local supported features for estimating BSS throughputs accurately
Add checks for features supported by the specific hardware mode of the
local device that has the channel for which the throughput is being
estimated instead of assuming the local device supports all optional
features. This is more accurate for cases where the local capabilities
might differ based on the band. In addition, this is in preparation for
extending rate estimates to cover optional VHT and HE features.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-05-07 12:27:21 +03:00
Ilan Peer
8c786e0687 PASN: Derive KDK only when required
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.

Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-04-10 11:55:55 +03:00
Ilan Peer
67014b3f74 PASN: Add support for comeback flow to wpa_supplicant
Process the received comeback cookie and retry automatically if the AP
allows this. Otherwise, provide the cookie to upper layers to allow a
later attempt with the cookie.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-03-21 18:28:34 +02:00
Ilan Peer
eaeec4da2d PASN: Add support for deauthentication flow in station
The new wpa_supplicant control interface command "PASN_DEAUTH
bssid=<BSSID>" can now be used to flush the local PTKSA cache for the
specified BSS and to notify the AP to request it to drop its PTKSA as
well.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-03-16 22:49:28 +02:00
Ben Greear
a746393dcf TWT: Allow specifying Control field value in TWT Request
See IEEE P802.11ax/D8.0, Figure 9-687 (Control field format) for
details.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2021-03-12 10:53:02 +02:00
Ben Greear
7fd2f24962 TWT: Support sending TWT Setup and Teardown Action frames
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2021-03-07 22:07:37 +02:00
Matthew Wang
5ac977758d Reject authentication start during explicit roam requests
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.

Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2021-03-06 10:59:05 +02:00
Jouni Malinen
f03580e319 Restore permanent MAC address on the FLUSH command
Clear previously used random MAC address on the FLUSH command if
mac_addr setting has been disabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-21 17:22:37 +02:00
Jouni Malinen
626fc0dcd0 Rename wpa_blacklist to wpa_bssid_ignore
This is more accurate name for this functionality of temporarily
ignoring BSSIDs.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-07 17:28:45 +02:00
Mikael Kanstrup
f7bbad5768 wpa_supplicant: Configurable fast-associate timer threshold
For Android the default value of 5 seconds is usually too short for
scan results from last scan initiated from settings app to be
considered for fast-associate. Make the fast-associate timer value
configurable so that a suitable value can be set based on a systems
regular scan interval.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
2021-02-06 16:56:30 +02:00
David Su
11355a122d Reset external_scan_running on interface deletion
Currently, the external_scan_running flag is not reset when an interface
is removed. Thus, if a connection attempt is made on another iface, it
will fail due to wpa_supplicant incorrectly assuming the radio is still
busy due to the ongoing scan.

To fix this, convert external_scan_running to a pointer to the interface
that started the scan. If this interface is removed, also reset the
pointer to NULL so that other operations may continue on this radio.

Test:
  1. Start scan on wlan0
  2. Remove wlan0
  3. Can connect to a network on wlan1

Signed-off-by: David Su <dysu@google.com>
2021-02-02 23:48:14 +02:00
Ilan Peer
9e7b980d65 PASN: Include RSNXE in the PASN negotiation
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 23:09:36 +02:00
Ilan Peer
5c65ad6c0b PASN: Support PASN with FT key derivation
Add support for PASN authentication with FT key derivation:

- As IEEE P802.11az/D2.6 states that wrapped data is optional and
  is only needed for further validation of the FT security parameters,
  do not include them in the first PASN frame.

- PASN with FT key derivation requires knowledge of the PMK-R1 and
  PMK-R1-Name for the target AP. As the WPA state machine stores PMK-R1,
  etc. only for the currently associated AP, store the mapping of
  BSSID to R1KH-ID for each previous association, so the R1KH-ID
  could be used to derive PMK-R1 and PMK-R1-Name. Do so instead
  of storing the PMK-R1 to avoid maintaining keys that might not
  be used.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 17:38:30 +02:00
Ilan Peer
8c6d2e2527 PASN: Support PASN with FILS key derivation
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
state machine.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 20:27:14 +02:00
Ilan Peer
a93ec28d10 PASN: Support PASN with SAE key derivation
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 20:27:14 +02:00
Ilan Peer
363768c8ac PASN: Add support for PASN processing to wpa_supplicant
Add PASN implementation to wpa_supplicant

1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.

The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.

The missing parts will be added in later patches.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 19:15:44 +02:00
Ilan Peer
d70060f966 WPA: Add PTKSA cache to wpa_supplicant for PASN
PASN requires to store the PTK derived during PASN authentication
so it can later be used for secure LTF etc. This is also true
for a PTK derived during regular connection.

Add an instance of a PTKSA cache for each wpa_supplicant
interface when PASN is enabled in build configuration.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 18:36:40 +02:00
Sunil Dutt
f39d6aacbb P2P: Recover p2p_find operation in case of failure to fetch scan results
Add a handler to notify failures to fetch the scan results and provide
an option to override default behavior of requesting a new scan in one
second in such an error condition. Use this new handler mechanism to
continue the p2p_find operation (by invoking p2p_scan_res_handled) for
an interim scenario where the p2p_scan attempt fails to get the scan
results from the driver which can happen, e.g., if there are parallel
updates to the cfg80211 scan results.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-12-21 23:04:54 +02:00
Jouni Malinen
6ead8b897f Use bool for is_6ghz variables and functions
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-12-11 19:56:14 +02:00
Veerendranath Jakkam
7131fede34 Extend the setband support for 6 GHz and band combinations
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-12-11 19:56:14 +02:00
Brian Norris
4b96fafcd8 D-Bus: Share 'remove all networks' with CLI
The D-Bus implementation of RemoveAllNetworks differs wildly from the
CLI implementation. Let's share the implementations.

This resolves use-after-free bugs I noticed, where we continue to use
the 'wpa_s->current_ssid' wpa_ssid object after freeing it, because we
didn't bother to disconnect from (and set to NULL) current_ssid before
freeing it.

Signed-off-by: Brian Norris <briannorris@chromium.org>
2020-10-10 20:39:00 +03:00
Kevin Lund
2fd35d9857 wpa_supplicant: Track consecutive connection failures
Within wpas_connection_failed(), the 'count' value of wpa_blacklist is
erroneously used as a tally of the number times the device has failed
to associate to a given BSSID without making a successful connection.
This is not accurate because there are a variety of ways a BSS can be
added to the blacklist beyond failed association such as interference
or deauthentication. This 'count' is lost whenever the blacklist is
cleared, so the wpa_supplicant stores an additional value
'extra_blacklist_count' which helps persist the 'count' through clears.
These count values are used to determine how long to wait to rescan
after a failed connection attempt.

While this logic was already slightly wrong, it would have been
completely broken by the upcoming change which adds time-based
blacklisting functionality. With the upcoming change, 'count' values
are not cleared on association, and thus do not necessarily even
approximate the "consecutive connection failures" which they were being
used for.

This change seeks to remove this unnecessary overloading of the
blacklist 'count' by directly tracking consecutive connection failures
within the wpa_supplicant struct, independent of the blacklist. This new
'consecutive_conn_failures' is iterated with every connection failure
and cleared when any successful connection is made. This change also
removes the now unused 'extra_blacklist_count' value.

Signed-off-by: Kevin Lund <kglund@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
2020-10-10 18:34:59 +03:00
Roy Marples
e8b85c078e iface match: Unspecified matched interfaces should not log driver fails
If there is no matching interface given, but interface matching is
enabled, all interfaces on the system will try to be initialized. Non
wireless interfaces will fail and the loopback device will be one of
these, so just log a diagnostic rather than an error.

Signed-off-by: Roy Marples <roy@marples.name>
2020-10-09 16:50:36 +03:00
Matthew Wang
4756ecabcf Allow bgscan parameters to be reconfigured
Teach wpa_supplicant to {de,}initialize bgscans when bgscan parameters
are set after initial connection.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2020-10-09 16:50:36 +03:00
Beniamino Galvani
1c58317f56 D-Bus: Allow changing an interface bridge via D-Bus
D-Bus clients can call CreateInterface() once and use the resulting
Interface object to connect multiple times to different networks.

However, if the network interface gets added to a bridge, clients
currently have to remove the Interface object and create a new one.

Improve this by supporting the change of the BridgeIfname property of
an existing Interface object.

Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
2020-10-09 15:18:10 +03:00
Vinita S. Maloo
d21dde9dac MSCS: Send MSCS change/remove frames only if MSCS setup exists
Allow MSCS change/remove request to be sent only after an initial setup,
i.e., after an add request has been accepted.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Vinita S. Maloo
af8ab3208d MSCS: Parse result of MSCS setup in (Re)Association Response frames
Add support to parse the (Re)Association Response frames to check if the
AP has accepted/declined the MSCS request in response to the
corresponding (Re)Association Request frame. AP indicates the result by
setting it in the optional MSCS Status subelement of MSCS Descriptor
element in (Re)Association Response frame.

This MSCS Status subelement is defined in the process of being added
into P802.11-REVmd/D4.0 (11-20-0516-17-000m-cr-mscs-and-cid4158).

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Vinita S. Maloo
bbd3178af4 MSCS: Add support to process MSCS Response frames
Add support to receive and process MSCS Response frames from the AP and
indicate the status to upper layers.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Vinita S. Maloo
a118047245 MSCS: Add support to send MSCS Request frames
Add support to send MSCS add/change/remove types of Action frames
to the connected AP.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:35 +03:00
Jouni Malinen
9304d1b3c3 DPP2: Regenerate Reconfig Announcement for each transmission
This is needed to generate a new unique A-NONCE and E'-id values.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-08 00:14:00 +03:00
Jouni Malinen
c6d0e5a93d DPP2: Add E-id in Reconfig Announcement
Add an encrypted Enrollee identifier into Reconfig Announcement frames
and decrypt that on the Configurator side. The actual E-id value is
currently not used for anything, but it can be used in the future to
provide better control over reconfiguration.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-07 22:54:53 +03:00
Veerendranath Jakkam
b28b9dfcbf OCV: OCI channel override support for testing (STA)
Add override parameters to use the specified channel while populating
OCI element in EAPOL-Key group msg 2/2, FT reassoc request, FILS assoc
request and WNM sleep request frames.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-08-03 11:02:13 +03:00
Jouni Malinen
15018d4f4a DPP2: Fix auth termination after receiving Configurator backup
remove_on_tx_status needs to be set in this case even if
dpp_config_processing=2 is used since there will be no connection
attempt when receiving a Configurator backup instead of station config
object.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-07-23 18:01:55 +03:00
Matthew Wang
d6b450e890 Refactor wpa_supplicant_need_to_roam()
Pull all the within-ESS roam code out of wpa_supplicant_need_to_roam()
and into its own function, wpa_supplicant_need_to_roam_within_ess().
This way, we avoid interleaving several #ifndef's in the original
function and wrap the new function in one big #ifndef. This also
modularizes the within-ESS roam code and makes it easier to test.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2020-06-19 18:30:08 +03:00
Vamsi Krishna
2d118f557a OCV: Add support to override channel info OCI element (STA)
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:01:44 +03:00
Jouni Malinen
0c043d9de7 DPP2: Reconfig Announcement transmission
Extend DPP chirping mechanism to allow Reconfig Announcement frames to
be transmitted instead of the Presence Announcement frames. Add a new
wpa_supplicant control interface command "DPP_RECONFIG <network id>" to
initiate reconfiguration for a specific network profile.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 16:41:33 +03:00
Jouni Malinen
0a488ef35c DPP: Track ending time for remain-on-channel operations
This may be needed to optimize use of offchannel TX operations with
wait-for-response when near the end of a pending remain-on-channel
operation.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-09 17:32:26 +03:00
Jouni Malinen
bb9e3935dd driver: Add second driver capability flags bitmap
All 64 bits of the capability flags bitmap are used, so add a new
variable to hold future capability bits.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-04-19 15:53:02 +03:00
Jouni Malinen
b2d8dc59f4 FT: Testing override for RSNXE Used subfield in FTE
Allow wpa_supplicant to be requested to override the RSNXE Used subfield
in FT reassociation case for testing purposes with "SET ft_rsnxe_used
<0/1/2>" where 0 = no override, 1 = override to 1, and 2 = override to
0.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-14 16:37:35 +03:00
P Praneesh
7c8f540ee0 wpa_supplicant: Add HE override support
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.

There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.

Signed-off-by: P Praneesh <ppranees@codeaurora.org>
2020-03-30 12:55:01 +03:00
Jouni Malinen
5058f771d9 DPP2: Allow station to require or not allow PFS
The new wpa_supplicant network profile parameter dpp_pfs can be used to
specify how PFS is applied to associations. The default behavior
(dpp_pfs=0) remains same as it was previously, i.e., try to use PFS if
the AP supports it. PFS use can now be required (dpp_pfs=1) or disabled
(dpp_pfs=2).

This is also working around an interoperability issue of DPP R2 STA with
certain hostapd builds that included both OWE and DPP functionality.
That issue was introduced by commit 09368515d1 ("OWE: Process
Diffie-Hellman Parameter element in AP mode") and removed by commit
16a4e931f0 ("OWE: Allow Diffie-Hellman Parameter element to be
included with DPP"). hostapd builds between those two commits would
reject DPP association attempt with PFS. The new wpa_supplicant default
(dpp_pfs=0) behavior is to automatically try to connect again with PFS
disabled if that happens.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 17:23:22 +02:00
Jouni Malinen
562f77144c DPP2: Chirping in wpa_supplicant Enrollee
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-27 20:05:25 +02:00
Jouni Malinen
4391ddd639 Use size_t instead of unsigned_int for last_scan_res
This avoids a theoretical unsigned integer overflow case with 32-bit
integers, but something that could potentially be hit with 16-bit int
(though, even that part looks pretty theoretical in this particular case
of number of BSSs in scan results).

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-22 18:50:04 +02:00
Jouni Malinen
eb26a6997d Allow SA Query to be disabled for testing purposes
The new wpa_supplicant control interface SET parameter disable_sa_query
can now be used to disable SA Query on receiving unprotected
disconnection event.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-21 18:12:02 +02:00
Jouni Malinen
f21fbfb977 Allow RSNE in EAPOL-Key msg 2/4 to be overridden for testing purposes
The new wpa_supplicant control interface parameter rsne_override_eapol
can be used similarly to the earlier rsnxe_override_eapol to override
the RSNE value added into EAPOL-Key msg 2/4.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-15 11:11:38 +02:00
Gurumoorthi Gnanasambandhan
1d9cff86bd Multi-AP: Set 4-address mode after network selection
Split multi_ap_process_assoc_resp() to set 4-address mode after network
selection. Previously, wpa_s->current_ssid might have been NULL in some
cases and that would have resulted in 4-address mode not getting enabled
properly.

Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
2020-03-13 17:00:19 +02:00
Ananya Barat
2b9713d616 Fill the current opclass in (Re)AssocRequest depending on HT/VHT IEs
The previous implementation was assuming a fixed 20 MHz channel
bandwidth when determining which operating class value to indicate as
the Current Operating Class in the Supported Operating Classes element.
This is not accurate for many HT/VHT cases.

Fix this by determining the current operating class (i.e., the operating
class used for the requested association) based on the HT/VHT operation
elements from scan results.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-11 18:30:31 +02:00
Veerendranath Jakkam
5fdacce465 Allow wildcard SSID to be enforced for a specific BSSID scan
Specific BSSID scan was replacing wildcard SSID with the known SSID if
any BSS with the specified BSSID is available in the known BSSes list.

Add control interface support to force use of a wildcard SSID in a
specific BSSID scan by user with the new "wildcard_ssid=1" argument to
the SCAN command.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-03-02 20:33:52 +02:00
Alexander Wetzel
1f90a49d02 STA: Allow PTK rekeying without Ext KeyID to be disabled as a workaround
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.

To allow affected users to mitigate the issues, add a new configuration
option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys with fast
reconnects.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-02-23 13:05:19 +02:00
Jouni Malinen
466e48dcd7 HT: Remove SMPS in AP mode
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.

Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-16 13:58:54 +02:00