Add even more workarounds for cfg80211 regulatory state clearing since
these DFS test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new test to check that the AP won't send frames to the client if
it tries to talk to itself.
Note that this fails until the relevant mac80211 patch is merged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in many test cases since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux kernel commit c9491367b759 ("mac80211: always update the PM state
of a peer on MGMT / DATA frames") enforces the AP to check only
mgmt/data frames PM bit, and to update station's power save accordingly.
When sending only a PS-Poll (control frame) the AP will ignore the PM
bit. As the result, the partial virtual bitmap will not be updated, and
the test ap_open_disconnect_in_ps will fail on tshark check. Since the
test needs only the TIM to be updated, setting PS enabled will send NDP
that will signal that the station is sleeping. Sending PS-Poll to enable
power save is not correct, according to the following standard
statement: "A PS-Poll frame exchange does not necessarily result in an
Ack frame from the AP, so a non-AP STA cannot change power management
mode using a PS-Poll frame."
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "iw connect ..." commands so that this would also work on
remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "ip link set up/down" commands so that this would also work on
remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This verifies that pmf=2 is ignored for a non-RSN network while a
network profile specific ieee80211w=2 is enforced.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The rfkill initialization will be moved out from
wpa_driver_nl80211_drv_init() which would break one step in this OOM
test case due to the memory allocation not existing anymore. Fix this by
skipping that OOM step to avoid causing false failures with the
following commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 4.8 vs 5.2 seem to compile eloop_register_sock() differently. With
5.2, that function name does not show up in the backtrace since
eloop_sock_table_add_sock() is used without a separate function call.
This broke the memory allocation failure checking in this test case. Fix
this by matching against the eloop_sock_table_add_sock() function which
shows up in the backtrace for both gcc versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd AP started unexpectedly, this test case would fail with
NameError due to incorrect variable name being used to construct the
exception text.
Signed-off-by: Jouni Malinen <j@w1.fi>
If wmediumd is available on the path, test that it can forward
packets between two virtual nodes and that stopping it makes
the regular in-kernel datapath do the needed work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It looks like a previous P2P test case can cause the initial single
channel scan in ap_open_select_twice take more than five seconds in some
cases. While that is not really expected behavior, this test case should
not fail. Increase the timeout to avoid reporting false failures here.
This could be triggered with the following test case sequence:
p2p_msg_unexpected_go_neg_resp ap_open_select_twice
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the second SELECT_NETWORK for the same network starts
a new scan immediately if the previous connection attempt is waiting for
the next scan iteration to start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ap_open_sta_enable_disable verifies that DISABLE_NETWORK that is issued
while connect/sme-connect radio work is pending is effective, i.e.,
prevents connection to disabled network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.
Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to a copy-paste error, these test cases left 4addr mode enabled on
wlan5. This resulted in number of connect_cmd_* test cases failing if
executed after the wpas_in_bridge tests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace fixed sleep with waiting for a disconnection event. In addition,
remove unnecessary use of sudo.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces use of the external hwsim_test tool for most data
connectivity test cases. Only the cases where a special interface
(bridge/VLAN) is used are still executed through hwsim_test.
The internal DATA_TEST_* functionality makes it easier to extend the
connectivity test cases through an external device with real WLAN
hardware instead of the hwsim test setup. In addition, the error reports
from this code can be made more informative.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
