Defines IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities
element and 6 GHz Operation Information field of HE Operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Some distros (e.g., Debian and Arch) already build wpa_supplicant with
support for TDLS, and Fedora is about to enable this feature as well.
Set CONFIG_TDLS=y in wpa_supplicant default build configuration.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
If the current country code cannot be fetched, do not try to report the
current value in the log since that will result in TypeError exception.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of VHT test cases missed explicit setting of hapd to None before
trying to start hostapd. Add those to avoid unexpected exceptions in
case hostapd start fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that clears ignore_old_scan_res parameter value instead
of doing this with try/finally in large number of test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that disables IPv6 and requires running
under a VM, rather than open-coding that many times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The freqlist parameter uses comma, not space, separated values. Add
another test case for checking freqlist values that do not use the
preferred channel numbers to make sure the frequency list is actually
used as a constraint for selecting the channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test for delayed group rekey retransmission that checks that
the IGTK is protected against it by not resetting the IPN replay
counter when reinstalling such a key.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While adding support for IGTK and BIGTK here, I tested this without
protections (i.e., with protections removed from both wpa_supplicant and
the driver), and while I got some bad resets on the debugfs values, it
should have failed with "unexpected connectivity".
Fix this to be correct - we need to reset the GTK PN, not the PTK PN in
this test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the gtk boolean by a keytype value indicating
GTK or PTK, to be able to extend to other types later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was apparently possible to hit the 20000 octet limit in some cases,
so increase the limit to avoid process termination due to insufficient
room for preparing a response to Introspect calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is not really appropriate for any kind of cross compilations and is
not really needed in general since system specific values can be set in
.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation used mp_rand_prime() to generate a random
value in range 0..m. That is insanely slow way of generating a random
value since mp_rand_prime() is for generating a random _prime_ which is
not what is needed here. Replace that implementation with generationg of
a random value in the requested range without doing any kind of prime
number checks or loops to reject values that are not primes.
This speeds up SAE and EAP-pwd routines by couple of orders of
magnitude..
Signed-off-by: Jouni Malinen <j@w1.fi>
When run after other tests, It was likely that the target
bss was already present in scan_fail, so the
scan_for_bss() wouldn't trip the allocation failure in
wpa_bss_add(). Flush the scan results before the scan to
ensure wpa_bss_add() is called and consistently pass
scan_fail.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
If sigma_dut is not installed, start_sigma_dut() will
throw an exception. Call start_sigma_dut() inside the
try/except to correctly reset the regulatory domain.
This fixes several seemingly random failures due to
regulatory domain not being reset.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Commit dd74ddd0df ("nl80211: Handle AKM suite selectors for AP
configuration") added warning log message "nl80211: Not enough room for
all AKM suites (num_suites=X > NL80211_MAX_NR_AKM_SUITES)" which in some
cases fills logs every 3 seconds, so fix this by increasing the log
message level to debug.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Ref: https://patchwork.ozlabs.org/project/openwrt/patch/20200504130757.12736-1-ynezz@true.cz/#2429246
Fixes: dd74ddd0df ("nl80211: Handle AKM suite selectors for AP configuration")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
It is possible for drivers to report received Management frames while AP
is going through initial setup (e.g., during ACS or DFS CAC). hostapd
and the driver is not yet ready for actually sending out responses to
such frames at this point and as such, it is better to explicitly ignore
such received frames rather than try to process them and have the
response (e.g., a Probe Response frame) getting dropped by the driver as
an invalid or getting out with some incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows nl80211-based drivers to get the frame out. The old earlier
location resulted in the driver operation getting rejected before the
kernel was not ready to transmit the frame in the BSS context of the AP
interface that has not yet been started.
While getting this broadcast Deauthentication frame transmitted at the
BSS start is not critical, it is one more chance of getting any
previously associated station notified of their previous association not
being valid anymore had they missed previous notifications in cases
where the AP is stopped and restarted.
Signed-off-by: Jouni Malinen <j@w1.fi>
cfg80211 takes care of key removal when link/association is lost, so
there is no need to explicitly clear old keys when starting AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux bridging code does not allow a station mode WLAN interface in a
bridge and this prevents the AP mode scan workaround from working if the
AP interface is in a bridge and scanning can be only done by moving to
STA mode. Extend this workaround to remove the interface from the bridge
temporarily for the duration of the scan, i.e., for the same duration as
the interface needs to be moved into the station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to be able to receive Public Action frames when hostapd
was initially started with start_disabled=1.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the local device becomes the handover selector, make the debug log
entries about client functionality not receiving the response clearer
since that is not really an error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow any channel to be used by not including a specific single channel
in the handover request without a need (for AP mode, use the current
operating channel). When sending out the handover select, pick a single
channel if no specific channel has been negotiated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Wait up to 100 ms for own handover request transmission to succeed if
peer handover request is received, but own crn is not yet available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Convert most print() calls to use the summary() helper so that the
printed information gets written into a log file as well. In addition,
start using a mutex lock to synchronize debug prints between threads to
avoid merging of messages from different contexts.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Address possible handover request collisions for cases where both
devices try to initiate handover simultaneously.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous version was trying to force the handover roles based on the
--init-on-touch parameter on both sides. That is fine for some test
scenarios, but not appropriate for more normal use cases. Change this
design to enable handover server in all cases and only control starting
of the handover client based on --init-on-touch.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to proceed with negotiated connection handover if
wpa_supplicant control interface is not available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was previously done only for the negotiated connection handover
case, but the same parameters are useful for the tag reading cases (URI
record and static handover).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd control interface command "DPP_CHIRP own=<BI ID>
iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started. This follows the model of similar
wpa_supplicant functionality from commit 562f77144c ("DPP2: Chirping
in wpa_supplicant Enrollee"). The hostapd case requires the AP to be
started without beaconing, i.e., with start_disabled=1 in hostapd
configuration, to allow iteration of channels needed for chirping.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clean struct hapd_interfaces pointers and interface count during
deinitialization at the end of theh ostapd process termination so that a
call to hostapd_for_each_interface() after this does not end up
dereferencing freed memory. Such cases do not exist before this commit,
but can be added after this, e.g., for DPP needs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When hostapd is started without beaconing (start_disabled=1), Public
Action frame transmission command through nl80211 needs to allow
offchannel operations regardless of the operating channel configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
