Commit graph

661 commits

Author SHA1 Message Date
Vinita S. Maloo
025f8ab52e SCS: Processing of SCS Response frames
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2021-08-12 18:28:07 +03:00
Veerendranath Jakkam
80bcd7ecd1 FILS: Flush PMKSA entries on FILS connection failure
wpa_supplicant generates both a PMKSA cache entry and ERP keys upon
successful FILS connection and uses FILS authentication algorithm for
subsequent connections when either ERP keys or a PMKSA cache entry is
available.

In some cases, like AP/RADIUS server restart, both ERP keys and PMKSA
becomes invalid. But currently when an AP rejects an association,
wpa_supplicant marks only ERP keys as failed but not clearing PMKSA.

Since PMKSA is not cleared, consecutive connection attempts are still
happening with FILS authentication algorithm and connection attempts are
failing with the same association rejection again instead of trying to
recover from the state mismatch by deriving a new ERP key hierarchy.

Clear PMKSA entries as well on association rejection from an AP to allow
the following connection attempt to go with open authentication to
re-establish a valid ERP key hierarchy. Also, since clearing PMKSA
entries on unprotected (Re)Association Response frames could allow DoS
attack (reduce usability of PMKSA caching), clear PMKSA entries only
when ERP keys exists.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-07-14 21:20:17 +03:00
Vamsi Krishna
1d2118b509 Check local supported features for estimating BSS throughputs accurately
Add checks for features supported by the specific hardware mode of the
local device that has the channel for which the throughput is being
estimated instead of assuming the local device supports all optional
features. This is more accurate for cases where the local capabilities
might differ based on the band. In addition, this is in preparation for
extending rate estimates to cover optional VHT and HE features.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-05-07 12:27:21 +03:00
Jouni Malinen
d675d3b15b Add helper functions for parsing RSNXE capabilities
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-04-10 12:43:38 +03:00
Sunil Dutt
0bae161229 Set last_eapol_matches_bssid=1 on a roam+auth indication from driver
Commit 3ab35a6603 ("Extend EAPOL frames processing workaround for
roaming cases") added a work around to address the issue of EAPOL frame
reception after reassociation replied to with an incorrect destination
address (the BSSID of the old AP). This is due to association events and
EAPOL RX events being reordered for the roaming cases with drivers that
perform BSS selection internally.

This mechanism relies on the fact that the driver always forwards the
EAPOL handshake to wpa_supplicant after the roaming (sets
last_eapol_matches_bssid during the EAPOL processing and resets on the
assoc/reassoc indication).

The above approach does not address the case where the driver does the
EAPOL handshake on the roam, indicating the authorized status to
wpa_supplicant but also forwards the EAPOL handshake to wpa_supplicant
for few other roam attempts. This is because the flag
last_eapol_matches_bssid is not set with the roam+authorized event from
the driver. Thus, the next reorder of roam and EAPOL RX events would
miss this workaround.

Address this by setting last_eapol_matches_bssid=1 on a roam+authorized
event from the driver.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-04-09 21:51:46 +03:00
Jouni Malinen
a826ff2d95 Ignore group-addressed SA Query frames
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-27 20:27:00 +02:00
Jouni Malinen
48cfb52b7e Rename blacklist.[ch] to bssid_ignore.[ch]
This completes renaming of this functionality for a list of temporarily
ignored BSSIDs.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-07 17:28:45 +02:00
Jouni Malinen
626fc0dcd0 Rename wpa_blacklist to wpa_bssid_ignore
This is more accurate name for this functionality of temporarily
ignoring BSSIDs.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-07 17:28:45 +02:00
Jouni Malinen
752b1c6081 Rename network profiles parameters for ignoring/accepted BSSIDs
Rename the network profile parameters bssid_blacklist and
bssid_whitelist to bssid_ignore and bssid_accept to use more specific
names for the configuration of which BSSs are ignored/accepted during
BSS selection. The old parameter names are maintained as aliases for the
new names to avoid breaking compatibility with previously used
configurations.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-07 16:18:26 +02:00
Mikael Kanstrup
f7bbad5768 wpa_supplicant: Configurable fast-associate timer threshold
For Android the default value of 5 seconds is usually too short for
scan results from last scan initiated from settings app to be
considered for fast-associate. Make the fast-associate timer value
configurable so that a suitable value can be set based on a systems
regular scan interval.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
2021-02-06 16:56:30 +02:00
Arowa Suliman
b829b7003a wpa_supplicant: Notify freq change on CH_SWITCH
wpa_supplicant does not send a D-Bus notification of the BSS frequency
change when a CSA happens. Sending a PropertyChanged signal with the
updated frequency will notify the network manager quickly, instead of
waiting for the next scan results.

Signed-off-by: Arowa Suliman <arowa@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
2021-02-06 16:50:19 +02:00
David Su
11355a122d Reset external_scan_running on interface deletion
Currently, the external_scan_running flag is not reset when an interface
is removed. Thus, if a connection attempt is made on another iface, it
will fail due to wpa_supplicant incorrectly assuming the radio is still
busy due to the ongoing scan.

To fix this, convert external_scan_running to a pointer to the interface
that started the scan. If this interface is removed, also reset the
pointer to NULL so that other operations may continue on this radio.

Test:
  1. Start scan on wlan0
  2. Remove wlan0
  3. Can connect to a network on wlan1

Signed-off-by: David Su <dysu@google.com>
2021-02-02 23:48:14 +02:00
Ilan Peer
363768c8ac PASN: Add support for PASN processing to wpa_supplicant
Add PASN implementation to wpa_supplicant

1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.

The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.

The missing parts will be added in later patches.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 19:15:44 +02:00
Ilan Peer
d70060f966 WPA: Add PTKSA cache to wpa_supplicant for PASN
PASN requires to store the PTK derived during PASN authentication
so it can later be used for secure LTF etc. This is also true
for a PTK derived during regular connection.

Add an instance of a PTKSA cache for each wpa_supplicant
interface when PASN is enabled in build configuration.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 18:36:40 +02:00
Sunil Dutt
f39d6aacbb P2P: Recover p2p_find operation in case of failure to fetch scan results
Add a handler to notify failures to fetch the scan results and provide
an option to override default behavior of requesting a new scan in one
second in such an error condition. Use this new handler mechanism to
continue the p2p_find operation (by invoking p2p_scan_res_handled) for
an interim scenario where the p2p_scan attempt fails to get the scan
results from the driver which can happen, e.g., if there are parallel
updates to the cfg80211 scan results.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-12-21 23:04:54 +02:00
Vamsi Krishna
084b3d2f8a Drop unexpected connection event while disconnected
If there is a disconnect command from wpa_supplicant immediately after
the driver sends a connection event to userspace but before that event
is received and processed by wpa_supplicant, wpa_supplicant processes
the disconnect command and a self-generated disconnected event first
followed by the connected event received from the driver. As a result
wpa_supplicant moves to the WPA_COMPLETED state.  Whereas the driver
processes the disconnect command received from wpa_supplicant after it
sends the connected event and moves to the disconnected state. Due to
this race between the disconnect command from wpa_supplicant and the
connected event from the driver, wpa_supplicant is moving to the
connected state though the driver is moving to the disconnected state
which results in abnormal functionality.

Ignore the connection event coming from the driver when wpa_supplicant
is not trying to connect after a disconnect command is issued but before
the next connect command is issued to fix the above mentioned race
condition.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-12-21 14:06:52 +02:00
Jouni Malinen
be7ee264f6 BSS: Use wrapper function for getting a pointer to the IE buffer
This makes it easier to change the internal struct wpa_bss design for
storing the variable length IE buffers.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-11-16 16:21:56 +02:00
Vinita S. Maloo
60c902f408 Add connect fail reason code from the driver to assoc reject event
Add support to report a vendor specific connect fail reason code fetched
from the driver to users by adding the reason code to the event
CTRL-EVENT-ASSOC-REJECT. Fetch the connect fail reason code when the
driver sends a failure connection result and append the reason code, if
available, to assoc reject event.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-11-16 13:15:28 +02:00
Kevin Lund
d530110028 wpa_supplicant: Implement time-based blacklisting
wpa_supplicant keeps a blacklist of BSSs in order to prevent repeated
associations to problematic APs*. Currently, this blacklist is
completely cleared whenever we successfully connect to any AP. This
causes problematic behavior when in the presence of both a bad AP and
a good AP. The device can repeatedly attempt to roam to the bad AP
because it is clearing the blacklist every time it connects to the good
AP. This results in the connection constantly ping-ponging between the
APs, leaving the user stuck without connection.

Instead of clearing the blacklist, implement timeout functionality which
allows association attempts to blacklisted APs after some time has
passed. Each time a BSS would be added to the blacklist, increase the
duration of this timeout exponentially, up to a cap of 1800 seconds.
This means that the device will no longer be able to immediately attempt
to roam back to a bad AP whenever it successfully connects to any other
AP.

Other details:
The algorithm for building up the blacklist count and timeout duration
on a given AP has been designed to be minimally obtrusive. Starting with
a fresh blacklist, the device may attempt to connect to a problematic AP
no more than 6 times in any ~45 minute period. Once an AP has reached a
blacklist count >= 6, the device may attempt to connect to it no more
than once every 30 minutes. The goal of these limits is to find an
ideal balance between minimizing connection attempts to bad APs while
still trying them out occasionally to see if the problems have stopped.

The only exception to the above limits is that the blacklist is still
completely cleared whenever there are no APs available in a scan. This
means that if all nearby APs have been blacklisted, all APs will be
completely exonerated regardless of their blacklist counts or how close
their blacklist entries are to expiring. When all nearby APs have been
blacklisted we know that every nearby AP is in some way problematic.
Once we know that every AP is causing problems, it doesn't really make
sense to sort them beyond that because the blacklist count and timeout
duration don't necessarily reflect the degree to which an AP is
problematic (i.e. they can be manipulated by external factors such as
the user physically moving around). Instead, its best to restart the
blacklist and let the normal roaming algorithm take over to maximize
our chance of getting the best possible connection quality.

As stated above, the time-based blacklisting algorithm is designed to
be minimally obtrusive to user experience, so occasionally restarting
the process is not too impactful on the user.

*problematic AP: rejects new clients, frequently de-auths clients, very
poor connection quality, etc.

Signed-off-by: Kevin Lund <kglund@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
2020-10-10 18:34:59 +03:00
Roy Marples
e8b85c078e iface match: Unspecified matched interfaces should not log driver fails
If there is no matching interface given, but interface matching is
enabled, all interfaces on the system will try to be initialized. Non
wireless interfaces will fail and the loopback device will be one of
these, so just log a diagnostic rather than an error.

Signed-off-by: Roy Marples <roy@marples.name>
2020-10-09 16:50:36 +03:00
Jouni Malinen
90e478aa0a DPP2: Use the PFS fallback if multiple key_mgmt values are enabled
Previously this fallback from PFS enabled to disabled (and back to
enabled) was used only if the local network profile used key_mgmt=DPP,
i.e., did not enable another other AKM. That leaves out some valid cases
since the local network profile could actually enable both DPP and SAE.
Extend this check to accept cases DPP AKM is enabled and it was selected
for the connection even if there other enabled AKMs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-09-23 23:06:55 +03:00
Vinita S. Maloo
af8ab3208d MSCS: Parse result of MSCS setup in (Re)Association Response frames
Add support to parse the (Re)Association Response frames to check if the
AP has accepted/declined the MSCS request in response to the
corresponding (Re)Association Request frame. AP indicates the result by
setting it in the optional MSCS Status subelement of MSCS Descriptor
element in (Re)Association Response frame.

This MSCS Status subelement is defined in the process of being added
into P802.11-REVmd/D4.0 (11-20-0516-17-000m-cr-mscs-and-cid4158).

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Vinita S. Maloo
bbd3178af4 MSCS: Add support to process MSCS Response frames
Add support to receive and process MSCS Response frames from the AP and
indicate the status to upper layers.

Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
2020-08-14 11:53:37 +03:00
Veerendranath Jakkam
596d99567a SME: Process channel switch event in SME only when supplicant's SME is used
Do not process channel switch event in wpa_supplicant's SME when SME is
offloaded to the driver/firmware to avoid SA Query initiation from both
wpa_supplicant and the driver/firmware for the OCV case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-13 21:39:49 +03:00
Veerendranath Jakkam
dbe485a35a SAE-PK: Check psk param also to look for SAE-PK acceptable BSS
SAE-PK password can be set using psk parameter also in case of mixed
SAE+PSK networks, so look for acceptable SAE-PK BSS when SAE password
not set and psk parameter meets SAE-PK password criteria.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-08-13 17:31:38 +03:00
Matthew Wang
b97aa038b7 Add WPA_EVENT_{DO,SKIP}_ROAM events
Add events for within-ESS reassociation. This allows us to monitor roam
events, both skipped and allowed, in tests.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2020-06-19 18:34:26 +03:00
Matthew Wang
d6b450e890 Refactor wpa_supplicant_need_to_roam()
Pull all the within-ESS roam code out of wpa_supplicant_need_to_roam()
and into its own function, wpa_supplicant_need_to_roam_within_ess().
This way, we avoid interleaving several #ifndef's in the original
function and wrap the new function in one big #ifndef. This also
modularizes the within-ESS roam code and makes it easier to test.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2020-06-19 18:30:08 +03:00
Jouni Malinen
fcef598ea2 Do not try to connect with zero-length SSID
It was possible to find a BSS to local network profile match for a BSS
entry that has no known SSID when going through some of the SSID
wildcard cases. At leas the OWE transition mode case without BSSID match
could result in hitting this. Zero-length SSID (i.e., wildcard SSID) is
not valid in (Re)Association Request frame, so such an association will
fail. Skip such a BSS to avoid known-to-be-failing association attempts.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-08 21:40:56 +03:00
Jouni Malinen
5f48d36b4a SAE-PK: Select SAE-PK network over SAE without PK
If there is an acceptable BSS with SAE-PK enabled in the same ESS,
select that over a BSS that does not enable SAE-PK when the network
profile uses automatic SAE-PK selection.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 16:49:07 +03:00
Jouni Malinen
d654ca24de Clean up wpa_scan_res_match()
Move the BSS-against-SSID matching into a separate helper function to
make this overly long function a bit more readable and to allow that
helper function to be used for other purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 16:30:32 +03:00
Jouni Malinen
9ad010c290 SAE-PK: Allow automatic SAE-PK to be disabled
This replaces the previously used sae_pk_only configuration parameter
with a more generic sae_pk that can be used to specify how SAE-PK is
negotiated. The default behavior (sae_pk=0) is to automatically
negotiate SAE-PK whenever the AP supports it and the password is in
appropriate format. sae_pk=1 allows only SAE-PK to be used and sae_pk=2
disables SAE-PK completely.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 11:55:16 +03:00
Jouni Malinen
1c846d647e SAE-PK: Allow SAE authentication without PK to be disabled
The new wpa_supplicant network profile parameter sae_pk_only=1 can now
be used to disable use of SAE authentication without SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
c2080e8657 Clear current PMKSA cache selection on association/roam
It was possible for the RSN state machine to maintain old PMKSA cache
selection (sm->cur_pmksa) when roaming to another BSS based on
driver-based roaming indication. This could result in mismatching state
and unexpected behavior, e.g., with not generating a Suite B PMKSA cache
entry.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 16:25:50 +03:00
Jouni Malinen
0a488ef35c DPP: Track ending time for remain-on-channel operations
This may be needed to optimize use of offchannel TX operations with
wait-for-response when near the end of a pending remain-on-channel
operation.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-09 17:32:26 +03:00
Jouni Malinen
12c8eacf73 DPP: Allow version number to be overridden for testing purposes
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:45 +03:00
Jouni Malinen
da8478a1ab EAPOL supp: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
0e794989e5 Beacon frame protection event for incorrect protection
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-01 16:22:48 +03:00
Jouni Malinen
5058f771d9 DPP2: Allow station to require or not allow PFS
The new wpa_supplicant network profile parameter dpp_pfs can be used to
specify how PFS is applied to associations. The default behavior
(dpp_pfs=0) remains same as it was previously, i.e., try to use PFS if
the AP supports it. PFS use can now be required (dpp_pfs=1) or disabled
(dpp_pfs=2).

This is also working around an interoperability issue of DPP R2 STA with
certain hostapd builds that included both OWE and DPP functionality.
That issue was introduced by commit 09368515d1 ("OWE: Process
Diffie-Hellman Parameter element in AP mode") and removed by commit
16a4e931f0 ("OWE: Allow Diffie-Hellman Parameter element to be
included with DPP"). hostapd builds between those two commits would
reject DPP association attempt with PFS. The new wpa_supplicant default
(dpp_pfs=0) behavior is to automatically try to connect again with PFS
disabled if that happens.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 17:23:22 +02:00
Jouni Malinen
d2d16e3100 Use size_t instead of int or unsigned int for configuration items
While int and unsigned int are not going overflow in practice as 32-bit
values, these could at least in theory hit an integer overflow with
16-bit int. Use size_t to avoid such potential issue cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-22 18:50:04 +02:00
Jouni Malinen
fab94f16e6 Indicate scan completion in active AP mode even when ignoring results
This is needed to avoid leaving external components (through control
interface or D-Bus) timing out while waiting for the scan completion
events. This was already taken care of for the scan-only case
("TYPE=only"), but the scan-and-allow-roaming case did not report the
scan completion event when operating in AP mode.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-15 21:18:16 +02:00
Jouni Malinen
f21fbfb977 Allow RSNE in EAPOL-Key msg 2/4 to be overridden for testing purposes
The new wpa_supplicant control interface parameter rsne_override_eapol
can be used similarly to the earlier rsnxe_override_eapol to override
the RSNE value added into EAPOL-Key msg 2/4.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-15 11:11:38 +02:00
Gurumoorthi Gnanasambandhan
1d9cff86bd Multi-AP: Set 4-address mode after network selection
Split multi_ap_process_assoc_resp() to set 4-address mode after network
selection. Previously, wpa_s->current_ssid might have been NULL in some
cases and that would have resulted in 4-address mode not getting enabled
properly.

Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
2020-03-13 17:00:19 +02:00
Jouni Malinen
3c73811507 OWE: Mark BSS for transition mode based on active OWE network profiles
It is possible for the hidden OWE BSS to be found based on SSID-specific
scan (e.g., from the special OWE scan mechanism). In that sequence, the
previously used learning of OWE BSS was skipped since the SSID was
already present in the BSS entry. This could result in not being able to
find a matching BSS entry for the OWE BSS in transition mode.

Fix this by adding the BSS flag for transition mode based on SSID
matching against currently enabled OWE network profiles in addition to
the previous mechanism.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:16:11 +02:00
Jouni Malinen
ecb5219d8c OWE: Avoid incorrect profile update in transition mode
The "unexpected" change of SSID between the current network profile
(which uses the SSID from the open BSS in OWE transition mode) and the
association with the OWE BSS (which uses a random, hidden SSID) resulted
in wpa_supplicant incorrectly determining that this was a
driver-initiated BSS selection ("Driver-initiated BSS selection changed
the SSID to <the random SSID from OWE BSS>" in debug log).

This ended up with updating security parameters based on the network
profile inwpa_supplicant_set_suites() instead of using the already
discovered information from scan results. In particular, this cleared
the RSN supplicant state machine information of AP RSNE and resulted in
having to fetch the scan results for the current BSS when processing
EAPOL-Key msg 3/4.

Fix this by recognizing the special case for OWE transition mode where
the SSID for the associated AP does not actually match the SSID in the
network profile.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-07 18:03:32 +02:00
Jouni Malinen
200c7693c9 Make WEP functionality an optional build parameter
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 17:45:25 +02:00
Alexander Wetzel
1f90a49d02 STA: Allow PTK rekeying without Ext KeyID to be disabled as a workaround
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.

To allow affected users to mitigate the issues, add a new configuration
option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys with fast
reconnects.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-02-23 13:05:19 +02:00
Veerendranath Jakkam
adf3de44ca Add check to consider band in enabling connection_vht flag
connection_vht flag was set to true when both Association Request and
Response frame IEs have VHT capability. Thus all devices that have
support for the vendor specific partial VHT support in the 2.4 GHz band
were also being reported as VHT capable. However, IEEE Std 802.11ac-2013
defines VHT STA to operate in frequency bands below 6 GHz excluding the
2.4 GHz band.

Do not set connection_vht when the operating band is 2.4 GHz. This
avoids reporting wifi_generation 5 on the 2.4 GHz band and reserves the
generation value 5 for full VHT as defined in the IEEE 802.11 standard.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-02-11 05:19:16 +02:00
Jouni Malinen
641d79f165 SAE: Special test mode sae_pwe=3 for looping with password identifier
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-10 05:13:13 +02:00
Jouni Malinen
e36a5894d0 SAE: Use H2E whenever Password Identifier is used
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
29dd0b3164 SAE H2E: Check H2E-only BSS membership selector only if SAE is enabled
This BSS membership selector has impact only for SAE functionality, so
ignore it when configured not to use SAE. This allows WPA-PSK connection
to and AP that advertises WPA-PSK and SAE while requiring H2E for SAE.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-20 21:17:28 +02:00
Jouni Malinen
dd530b8739 Silence compiler warning with CONFIG_NO_ROAMING=y
Comment out unused static functions if CONFIG_NO_ROAMING is defined.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-09 12:40:17 +02:00
Vamsi Krishna
33c8a10498 Do not select APs found on disabled channels for connection
If a channel list changed event is received after a scan and before
selecting a BSS for connection, a BSS found on a now disabled channel
may get selected for connection. The connect request issued with the BSS
found on a disabled channel is rejected by cfg80211. Filter out the BSSs
found on disabled channels and select from the other BSSs found on
enabled channels to avoid unnecessary connection attempts that are bound
to fail.

The channel list information will be updated by the driver in cases like
country code update, disabling/enabling specific bands, etc. which can
occur between the scan and connection attempt.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-08 16:19:47 +02:00
Jouni Malinen
c8eb7fe66c Fix signal_poll based roaming skip
Fix a rebasing issue in the signal difference calculation. The older
patch was not updated to use the new cur_level local variable to get the
possibly updated signal level for the current BSS.

Fixes: a2c1bebd43 ("Improve roaming logic")
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-02 20:34:39 +02:00
Jouni Malinen
ad2f096609 Maintain BSS entries for 5 seconds after interface is disabled
This is targeting the case of MAC address change for an association
which may require the interface to be set down for a short moment.
Previously, this ended up flushing the BSS table that wpa_supplicant
maintained and that resulted in having to scan again if the MAC address
was changed between the previous scan and the connection attempt. This
is unnecessary extra latency, so maintain the BSS entries for 5 seconds
(i.e., the same time that the old scan results are consider valid for a
new connection attempt) after an interface goes down.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-02 12:58:58 +02:00
Jouni Malinen
988f14448a Indicated if the selected BSS is the current BSS
This makes scan result processing a bit more readable in debug log.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 17:55:26 +02:00
Jouni Malinen
a8ad9c31db Make min_diff determination from cur_level more readable
This handles both the dBm and unspecified unit cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 17:46:03 +02:00
Jouni Malinen
41f72d7356 Use sel_est consistently with cur_sel in wpa_supplicant_need_to_roam()
This makes the code a bit easier to read.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 17:37:58 +02:00
Matthew Wang
a2c1bebd43 Improve roaming logic
Currently, wpa_supplicant may roam too aggressively; the need_to_roam()
function will return early with a roaming decision if the difference in
signal level or throughput between the current and selected APs is
"sufficiently large." In particular, if the selected AP's estimated
throughput is more than 5k greater than the current AP's estimated
throughput, wpa_supplicant will decide to roam. Otherwise, if the
selected AP's signal level is less than the current AP's signal level,
or the selected AP's estimated throughput is at least 5k less than the
current AP's estimated throughput, wpa_supplicant will skip the roam.
These decisions are based only on one factor and can lead to poor
roaming choices (e.g., a roam should not happen if the selected AP's
estimated throughput meets the threshold but the current signal and
throughput are already good, whereas a roam should happen if the signal
is slightly worse but the estimated throughput is significantly better).

This change standardizes the roaming heuristic for signal strength
difference requirements and will hopefully improve user experience. The
change can be summarized as follows: based on the current signal level,
a certain roaming difficulty is assigned. Based on the selected AP's
estimated throughput relative to the current AP's estimated throughput,
the difficulty is adjusted up or down. If the difference in signal level
meets the threshold, a roam happens.

The hard-coded values were selected purely based on the previous version
of this function. They may eventually need to be fine-tuned for optimal
performance.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2020-01-01 17:33:51 +02:00
Jouni Malinen
9c8d550b77 Allow roam to lower signal level if throughput benefit is significant
Do not prevent roam to a different BSS based only on the signal level
with the current BSS being higher than with the selected BSS. If the
estimated throughput is significantly higher (> 20%), allow roaming if
the following conditions are met.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 17:09:18 +02:00
Jouni Malinen
9fafefb9e5 Skip roaming based on signal level difference if current SNR is good
If the current SNR with the associated BSS is sufficiently good (better
than GREAT_SNR = 25), there is limited benefit from moving to another
BSS even if that BSS were to have a higher signal level. As such, skip
roaming based on the signal level difference between the selected BSS
from scan results and the current BSS for such cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 16:56:40 +02:00
Jouni Malinen
f4f7600adf Use signal_poll noise information for roaming, if available
Using average signal strength from the driver and hardcoded noise floor
does not look like an ideal design since there can be significant
differences in the driver-reported noise floor values. Furthermore, even
though the current noise floor is a snapshot from the driver, it is
common for drivers to use a noise floor value from a longer calibration
step and that should not prevent the driver provided value from being
used. This makes the comparisons of the signal strengths between the
current AP (signal_poll) and other APs (scan) more accurate.

As an example, test runs in home environment showed 5 dB difference
between the driver reported noise floor and the hardcoded value and this
could result in significant differences in estimated throughput
calculation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-01 13:38:11 +02:00
Matthew Wang
69ccc557d8 wpa_supplicant: Fall back to avg_signal in roaming decision
Some drivers (e.g. Marvell WiFi) don't report avg_beacon_signal, but
it's still useful to poll for the signal again when a roaming decision
needs to be made. Use si.avg_signal when si.avg_beacon_signal is not
available.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-12-31 00:23:42 +02:00
Emmanuel Grumbach
7e7b23e229 Update throughput estimate for the current BSS based on signal poll
We saw that on certain platforms in certain places we keep switching
between two APs and eventually get the same RSSI. Debugging showed that
we have a very big difference between the two antennas.

Ant A can hear AP A very well (-60) but AP B very bad (-80)
Ant B can hear AP B very well (-60) but AP A very bad (-80)

When the device associates to AP A, it'll learn to use Ant A. If the
device uses one single antenna to receive the scan results, it may hear
the AP it is currently associated to on the second antenna and get bad
results. Because of that, the wpa_supplicant will roam to the other AP
and the same scenario will repeat itself:

Association to AP A (Ant A reports -60).
Scan on Ant A: AP A: -60, AP B: -80
Scan on Ant B: AP A: -80, AP A: -60 ==> ROAM.

Association to AP B (Ant B reports -60)
Scan on Ant A: AP A: -60, AP B: -80 ==> ROAM

Etc...

Improve this by querying the signal level of the current AP using
drv_signal_poll() instead of relying on the signal level that we get
from the scan results. Also update the throughput estimate based on the
likely more accurate values for the current association.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2019-12-31 00:21:37 +02:00
Emmanuel Grumbach
98ea9d5d51 Use local variables for current BSS signal strength in roaming
This is a step towards allowing these values to be determined based on
signal poll instead of scan results.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2019-12-30 23:57:47 +02:00
Sergey Matyukevich
078217a2d7 STA OBSS: Update secondary channel info after CSA
Field wpa_s->sme.ht_sec_chan keeps secondary channel for the 40 MHz
band. This field is used to prepare a list of channels for the STA OBSS
scan. Initially, the secondary channel is set to HT_SEC_CHAN_UNKNOWN.
Later on, in function wpa_obss_scan_freq_list() it is obtained from the
current BSS HT operation IE. However, the secondary channel information
is not updated after channel switch, which may lead to an incorrect list
of channels prepared for the STA OBSS scan.

Update ht_sec_chan according to the channel switch event data to fix
this.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2019-12-27 21:04:57 +02:00
Sergey Matyukevich
3204795d7a STA OBSS: Add check for overlapping BSSs
In the previous implementation connected STA performs OBSS scan
according to requests from its 20/40 MHz AP. However STA checks only 40
MHz intolerance subfield from HT Capabilities element in scan results.
Meanwhile, as per IEEE Std 802.11-2016, 11.16.12, STA should check
overlapping BSSs as well.

Note that all the required code to check overlapping BSSs did already
exist for AP mode since AP does those checks properly before operating
as 20/40 MHz BSS in the 2.4 GHz band. Use that existing code by replace
existing 40 MHz intolerance check in sme_proc_obss_scan() with the new
shared helper function check_bss_coex_40mhz().

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2019-12-26 11:41:01 +02:00
Alexander Wetzel
84877f253d wpa_supplicant: Do not try to detect PSK mismatch during PTK rekeying
When a PTK rekey fails it can't be caused by a PSK mismatch. Report a
possible PSK mismatch only during the initial 4-way handshake to avoid
incorrect reports.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2019-12-21 17:10:17 +02:00
Jouni Malinen
e3c476bd8c SAE H2E: Fix RSNXE override in EAPOL-Key msg 2/4 for testing purposes
The previous implementation missed the case where EAPOL-Key frame may be
reported as having been received before the association event is
processed. This would have resulted in not using the RSNXE override for
EAPOL-Key msg 2/4 when the pending EAPOL-Key frame gets processed
immediately after processing the association event. Fix this by moving
the override case to be handled before that.

Fixes: 1325655397 ("SAE H2E: RSNXE override for testing purposes")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-13 03:08:27 +02:00
Jouni Malinen
1325655397 SAE H2E: RSNXE override for testing purposes
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 12:54:54 +02:00
Jouni Malinen
405946d76a SAE: Testing option to ignore H2E requirement mismatch
"SET ignore_sae_h2e_only 1" can now be used to configurate
wpa_supplicant to a test mode where it ignores AP's H2E-required
advertisement and try to connect with hunt-and-pecking loop instead.
This is used only for testing AP behavior with unexpected STA behavior.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-06 17:13:59 +02:00
Jouni Malinen
50a2c8c906 Do not indicate possible PSK failure when using SAE
wpa_key_mgmt_wpa_psk() includes SAE AKMs. However, with SAE, there is no
way of reaching 4-way handshake without the password having already been
verified as part of SAE authentication. As such, a failure to complete
4-way handshake with SAE cannot indicate that the used password was
incorrect.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-10-27 12:54:40 +02:00
Jouni Malinen
6d6c887751 SAE: Add RSNXE in Association Request and EAPOL-Key msg 2/4
Add the new RSNXE into (Re)Association Request frames and EAPOL-Key msg
2/4 when using SAE with hash-to-element mechanism enabled. This allows
the AP to verify that there was no downgrade attack when both PWE
derivation mechanisms are enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-17 16:54:05 +03:00
Jouni Malinen
cfe1ea5c9c SAE: H2E version of SAE commit message handling for STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
146889e3ca RSN: Verify RSNXE match between Beacon/ProbeResp and EAPOL-Key msg 3/4
If the AP advertises RSN Extension element, it has to be advertised
consistently in the unprotected (Beacon and Probe Response) and
protected (EAPOL-Key msg 3/4) frames. Verify that this is the case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
293a01f3b3 SAE: Handle BSS membership selector indication for H2E-only in STA mode
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Ankita Bajaj
c349174035 MBO/OCE: Update disable_mbo_oce flag after association
After roaming to an AP, update disable_mbo_oce flag based on the current
BSS capabilities. This flag is used to check whether STA should support
MBO/OCE features and process BTM request received from the current
connected AP.

When a STA roams from a WPA2 MBO/OCE AP with PMF enabled to a
misbehaving WPA2 MBO/OCE AP without PMF, or if the driver chooses a BSS
in which PMF is not enabled for the initial connection, BTM requests
from such APs should not be processed by STA.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-01 16:45:15 +03:00
Vamsi Krishna
2e06cef80a MBO/OCE: Work around misbehaving MBO/OCE APs that use RSN without PMF
The MBO and OCE specification require the station to mandate use of PMF
when connecting to an MBO/OCE AP that uses WPA2. The earlier
implementation prevented such misbehaving APs from being selected for
connection completely. This looks like the safest approach to take, but
unfortunately, there are deployed APs that are not compliant with the
MBO/OCE requirements and this strict interpretation of the station
requirements results in interoperability issues by preventing the
association completely.

Relax the approach by allowing noncompliant MBO/OCE APs to be selected
for RSN connection without PMF to avoid the main impact of this
interoperability issue. However, disable MBO/OCE functionality when PMF
cannot be negotiated to try to be as compliant as practical with the
MBO/OCE tech spec requirements (i.e., stop being an MBO/OCE STA for the
duration of such workaround association). Also disable support for BTM
in this workaround state since MBO would expect all BTM frames to be
protected.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-21 00:58:33 +03:00
Jouni Malinen
16ef233bf1 DPP2: Connection status result (Enrollee)
Add support for reporting connection status after provisioning if the
Configurator requests this.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-16 17:25:34 +03:00
Jouni Malinen
7d2ed8bae8 Remove CONFIG_IEEE80211W build parameter
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-09-08 17:33:40 +03:00
Ankita Bajaj
0028d627c8 OCE: Mandate PMF for WPA2 association with OCE AP
An OCE AP with WPA2 enabled shall require PMF negotiation when
associating with an OCE STA. An OCE STA-CFON may negotiate PMF with a
STA when it is operating as an AP. Don't select an OCE AP for connection
if PMF is not enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-15 19:06:53 +03:00
Jouni Malinen
b0b25c5bbc Clear external eapSuccess setting in driver-authorized cases
The conditions for the eapol_sm_notify_eap_success(FALSE) calls did not
cover the case where eapol_sm_notify_eap_success(TRUE) had been called
based on offloaded 4-way handshake and driver notification of
authorization in wpa_supplicant_event_port_authorized(). This could
result in eapSuccess and altSuccess state machine variables being left
TRUE when roaming to another BSS and that results in EAP failure if the
following roaming case does not get fully authorized through the driver
offload.

Fix this by clearing eapSuccess/altSuccess when processing a new
association (including roaming) event and also when disconnecting from
the network.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-07 19:24:06 +03:00
Sunil Dutt
3263fca289 Set the default scan IEs on interface restart
Previously, these default scan IEs were set only when parameter values
changed and during the interface initialization, which can get lost in
the driver on an interface restart. Hence, also set these IEs on an
interface restart notification even when there has been no change in the
values since the last update to the driver.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-07 11:43:12 +03:00
Sven Eckelmann
f74618cb92 wpa_supplicant: Fix type for ssid->mode comparisons
The ssid->mode is from type enum wpas_mode and all its constants start
with WPAS_MODE_*. Still some of the code sections used the
IEEE80211_MODE_* defines instead of WPAS_MODE_*.

This should have no impact on the actual code because the constants for
INFRA, IBSS, AP and MESH had the same values.

Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
2019-06-23 18:03:51 +03:00
Ankita Bajaj
a8391db7cf OCE: Use RSSI of actual BSS which rejected association
If an AP rejects association due to low RSSI, then RSSI of the BSS from
which association reject is received shall be used for calculating RSSI
threshold at which STA can try connecting back to that BSS later. In
case of SME offload, the current_bss might not have been set before
receiving association completion, so fetch the BSS entry based on the
BSSID provided in the driver event.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-05-31 16:52:10 +03:00
Omer Dagan
95f556f3c7 Make channel switch started event available over control interface
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.

Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
2019-04-22 22:08:07 +03:00
Alex Khouderchah
cfde99a84b Add 802.11 reason code strings into wpa_supplicant messages
Logs involving IEEE 802.11 Reason Codes output the Reason Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each Reason Code using the latter part
of the reason code #define names.

Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
2019-04-22 22:08:05 +03:00
Avraham Stern
fe01cd0067 Fix FILS ERP association event with 4-way HS offload drivers
When FILS authentication is used with ERP, no EAPOL frames are expected
after association. However, for drivers that set the
WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_8021X capability flag, the EAP state
machine was not configured correctly and was waiting for EAPOL frames,
which leads to disconnection.

Fix this by reordering the if branches to set the EAPOL/EAP state
machines to success when FILS authentication was already completed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2019-04-16 01:53:21 +03:00
Jouni Malinen
10ec6a5f38 DPP2: PFS for PTK derivation
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-18 18:32:31 +02:00
Jouni Malinen
e3b5bd81bd UBSan: Fix RRM beacon processing attempt without scan_info
Some driver interfaces (e.g., wext) might not include the
data->scan_info information and data could be NULL here. Do not try to
call the RRM handler in this case since that would dereference the NULL
pointer when determining where scan_info is located and could
potentially result in trying to read from unexpected location if RRM is
enabled with a driver interface that does not support it.

events.c:1907:59: runtime error: member access within null pointer of type 'union wpa_event_data'

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-02-25 19:43:11 +02:00
Lior David
2c129a1b71 Fix cipher suite selector default value in RSNE for DMG
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).

It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.

In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.

Signed-off-by: Lior David <liord@codeaurora.org>
2019-02-21 12:42:24 +02:00
Davina Lu
83ebf55865 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the backhaul STA needs to add
a Multi-AP IE to the WFA vendor extension element in the WSC M1 message
that indicates it supports the Multi-AP backhaul STA role. The Registrar
(if it support Multi-AP onboarding) will respond to that with a WSC M8
message that also contains the Multi-AP IE, and that contains the
credentials for the backhaul SSID (which may be different from the SSID
on which WPS is performed).

Introduce a new parameter to wpas_wps_start_pbc() and allow it to be
set via control interface's new multi_ap=1 parameter of WPS_PBC call.
multi_ap_backhaul_sta is set to 1 in the automatically created SSID.
Thus, if the AP does not support Multi-AP, association will fail and
WPS will be terminated.

Only wps_pbc is supported.

This commit adds the multi_ap argument only to the control socket
interface, not to the D-Bus interface.

Since WPS associates with the fronthaul BSS instead of the backhaul BSS,
we should not drop association if the AP announces fronthaul-only BSS.
Still, we should only do that in the specific case of WPS. Therefore,
add a check to multi_ap_process_assoc_resp() to allow association with a
fronthaul-only BSS if and only if key_mgmt contains WPS.

Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
2019-02-18 22:35:41 +02:00
Jouni Malinen
3f8ceff54c Indicate wifi_generation in wpa_supplicant STATUS output
This adds a wifi_generation=4/5/6 line to the STATUS output if the
driver reports (Re)Association Request frame and (Re)Association
Response frame information elements in the association or connection
event. Only the generations 4 (HT = 802.11n), 5 (VHT = 802.11ac), and 6
(HE = 802.11ax) are reported.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-02-15 02:09:41 +02:00
Arend van Spriel
436ee2fd93 drivers: Add separate driver flags for 802.1X and PSK 4-way HS offloads
Allow drivers to indicate support for offloading 4-way handshake for
either IEEE 802.1X (WPA2-Enterprise; EAP) and/or WPA/WPA2-PSK
(WPA2-Personal) by splitting the WPA_DRIVER_FLAGS_4WAY_HANDSHAKE flag
into two separate flags.

Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
2019-01-08 01:12:02 +02:00
Peter Oh
0332c27e32 mesh: Consider mesh interface on DFS event handler
Once mesh starts supporting DFS channels, it has to handle DFS related
events from drivers, hence add mesh interface to the check list.

Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2019-01-03 13:31:55 +02:00
Alex Khouderchah
38b405c8f0 dbus: Expose authentication status to D-Bus
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.

This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.

Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
2019-01-03 00:39:12 +02:00
Matthew Wang
2bbad1c7c9 dbus: Export roam time, roam complete, and session length
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-01-03 00:20:34 +02:00
Beni Lev
19677b77c3 OCE: Add RSSI based association rejection support (STA)
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.

Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).

Signed-off-by: Beni Lev <beni.lev@intel.com>
2019-01-01 17:56:25 +02:00
Jouni Malinen
32bb47faa1 Update wpa_supplicant channel list on FLUSH
Try to make sure the driver channel list state is synchronized with
wpa_supplicant whenever explicitly clearing state (e.g., between hwsim
test cases).

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-01 15:58:46 +02:00
Venkateswara Naralasetty
5abc7823bd wpa_supplicant: Add Multi-AP backhaul STA support
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.

This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.

Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2018-12-20 12:10:31 +02:00
Mathy Vanhoef
f91e68e903 OCV: Perform an SA Query after a channel switch
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00