Fix a memory leak exposed by the dpp_own_config_sign_fail test.
Fixes: 52d469de11 ("DPP2: Support multiple Config Objects in Enrollee")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Ongoing scan could prevent the station Enrollee from sending out DPP
connection status after the 15 second timeout and that would result in
the Configurator timing out on the wait for the status report. Abort any
ongoing scan, if needed, to avoid this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enable all DH FFC groups for SAE in wpa_supplicant testing builds. These
are needed to allow more testing coverage for AP functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO with
attributes defined in enum qca_wlan_vendor_attr_get_sta to get
information for a BSS in STA mode or for a peer STA in AP mode. This
vendor sub command can be used to get STA information from the driver to
userspace. The attributes defined in enum
qca_wlan_vendor_attr_get_sta_info are used to encapsulate required
information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only HE mode is allowed in the 6 GHz band hence do not enable HT/VHT
even if they are configured by the user.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using the channel parameter for validating allowed channel combinations
is not scalable to add 6 GHz support in the future since channel numbers
are duplicated between 2.4 GHz / 5 GHz bands and 6 GHz band. Hence use
frequency field for all channel combination validation steps done before
starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
After receiving ACS offload results, select the current hw_mode based on
the frequency selected by the ACS algorithm. The current hw_mode will be
further used during other validation steps such as HT capability
validations, DFS validation, etc.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using channel field while starting AP will cause issues with the new
6GHz band as the channel numbers are duplicated between the different
bands. Populate iface->freq before starting AP so that it can be used
instead of the channel number for all validations that need to be done
while starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace channel fields with frequency fields in ACS completed event
interface from the driver layer. Use
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY attributes if the driver
includes them in the QCA_NL80211_VENDOR_SUBCMD_DO_ACS event, otherwise
use QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL attributes to maintain
backwards compatibility with old drivers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Search through all hw_features sets whose mode is same as the input mode
while finding channel corresponding to the input frequency in
hw_get_channel_freq().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Iterate through all hw_features sets and populate channels from all
hw_features sets whose hardware mode is matching the configured hardware
mode while preparing the channel list for ACS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a P2P connection over P802.11ay EDMG channels to achieve the
highest link speed that the standard allows for channel bonding (CB) up
to CB4.
Let each P2P peer add its EDMG channels to the Supported Channels IE
advertised in P2P GO negotiation. Give EDMG channels priority when peers
negotiate for operating channel.
User may add 'edmg' parameter to p2p_connect, p2p_add_group, and
p2p_invite commands to prefer an EDMG channel for the P2P link. User may
also set p2p_go_edmg=1 in wpa_supplicant configuration file to prefer
EDMG.
When EDMG is used, P2P will try to find the highest channel bonding
supported channel that matches the frequency parameter, if the devices
do not support EDMG, the P2P connection will use a legacy (1-6) 60 GHz
channel.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Update new channels in Channel Bonding (CB2 ... CB4) in the 60 GHz band
for different regulatory regions according to the latest draft amendment
IEEE P802.11ay/D5.0.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Add EDMG bandwidth to CHANWIDTH_ defines.
Update API ieee80211_freq_to_channel_ext() to support EDMG bandwidth
for EDMG channels.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
The 127.0.0.11/24 address that could have been left on the wlan0
interface resulted in some test case sequence failures. Fix this by
explicitly clearing that address when terminating sigma_dut.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
start_sigma_dut() can raise an exception and as such, assigning a
variable to its return value within a try block does not work in this
manner when the result is supposed to be used in the finally statement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The second round may use PMKSA caching, but AP will need to reject msg
2/4 in that case as well due to RSNXE mismatch.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous implementation missed the case where EAPOL-Key frame may be
reported as having been received before the association event is
processed. This would have resulted in not using the RSNXE override for
EAPOL-Key msg 2/4 when the pending EAPOL-Key frame gets processed
immediately after processing the association event. Fix this by moving
the override case to be handled before that.
Fixes: 1325655397 ("SAE H2E: RSNXE override for testing purposes")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for testing purposes to be able to check which groups
a STA reports as having been rejected when using SAE H2E.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new hostapd configuration parameter rsnxe_override_eapol=<hexdump>
can be used to override RSNXE value in EAPOL-Key msg 3/4 for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
check_sae_rejected_groups() returns 1, not -1, in case an enabled group
is rejected. The previous check for < 0 could not have ever triggered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET extra_sae_rejected_groups <groups>" can now be used to enable test
mode in which wpa_supplicant will report additional groups (configured
as space separated integers) when using SAE H2E.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET ignore_sae_h2e_only 1" can now be used to configurate
wpa_supplicant to a test mode where it ignores AP's H2E-required
advertisement and try to connect with hunt-and-pecking loop instead.
This is used only for testing AP behavior with unexpected STA behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
freq_list is built in allocated heap memory and it needs to be freed
before returning from this function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clean up do_acs interface to not pass ch_list to drivers as the same
information is available in freq_list. The channel numbers are
duplicated between 2.4 GHz and 5 GHz bands and the 6 GHz band. So, use
the QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST to populate only 2.4 GHz and 5 GHz
channels to ensure backwards compatibility with old drivers which do not
have support to decode the newer QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Skip DFS checks and CAC operation for 6 GHz channels. AFC checks
will be added for 6 GHz channels later.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
HT capability check is not required when starting AP on 6 GHz band as
only HE operation mode is allowed in the 6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
