Number of cred block fields were not saved when wpa_supplicant is
writing the configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP does not advertize EAP parameters, default to TTLS/MSCHAPv2
when using username/password credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The current PMKSA cache entry needs to be clear to allow EAPOL
reauthentication to be started in case this association used PMKSA
caching.
Signed-hostap: Jouni Malinen <j@w1.fi>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
pmksa_cache_free_entry() takes care of updated the list head pointer
(pmksa->pmksa), so no need to do this change in the caller.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the shared_secret pointer from RADIUS client implementation instead
of getting this from hostapd configuration data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
If the global pmf=1/2 parameter is used to enable PMF for Interworking
networks, add WPA-EAP-SHA256 to the temporary network block to allow
connection to PMF required APs.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This prevents situations like the following where we roam to a
lesser quality BSS just because the signal level delta is over our
threshold.
wlan0: Considering within-ESS reassociation
wlan0: Current BSS: 00:24:6c:74:0a:40 level=-51
wlan0: Selected BSS: 00:24:6c:74:0a:e0 level=-64
wlan0: Request association: reassociate: 0 selected: 00:24:6c:74:0a:e0
bssid: 00:24:6c:74:0a:40 pending: 00:00:00:00:00:00 wpa_state: COMPLETED
Signed-hostap: Robert Shade <robert.shade@gmail.com>
If netlink_init() fails on socket create or bind the cfg struct
provided as parameter is freed by netlink_init(). Callers of
netlink_init() also free this struct on their error paths leading
to double free.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
This allows the ctrl_iface STATUS information to be used to determine
which Home SP credential (domain in the cred block) was used and whether
the network is operated by the home SP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows credential entries to be removed based on SP FQDN without
having to iterate through the configured entries from an external
program to figure out which credentials should be removed for a specific
SP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the credential that was used to create a temporary HS 2.0 network
block is removed, remove the network block, too.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant is started from /init.*.rc on Android and that seems
to be using umask 0077 which would leave the control interface
directory without group access. This breaks things since Wi-Fi
framework assumes that this directory can be accessed by other
applications in the wifi group. Fix this by adding group access even
if umask value would prevent this.
In most cases, this issue was not hit since the control interface
directory is normally created by that same init.*.rc file with suitable
mode and wpa_supplicant is killed in the way that does not allow it to
remove the file. However, if wpa_supplicant is allowed stop cleanly, it
will remove the directory and the next start could result with the Wi-Fi
framework not being able to use Wi-Fi (and GUI not showing Wi-Fi getting
enabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the maximum retry limit from 10 to 120 to match the behavior
used with GO Negotiation Request frames when trying to start GO
Negotiation with a peer that does not acknowledge frames (e.g., due
to being in sleep or on another channel most of the time).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PD Request retry limit can be used to achieve the same behavior,
so drop this duplicated timeout mechanism and control the timeout
based on MAX_PROV_DISC_REQ_RETRIES.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ee431d77a5 broke wpa_supplicant
compilation:
../src/ap/ieee802_1x.o: In function `ieee802_1x_get_eap_user':
/../src/ap/ieee802_1x.c:1689: undefined reference to `hostapd_get_eap_user'
collect2: error: ld returned 1 exit status
make: *** [wpa_supplicant] Error 1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NL80211_CMD_TDLS_OPER command can be used as an event based on a
recent cfg80211 commit, so add code to map that to internal
wpa_supplicant event to request TDLS link setup/teardown.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some network parameters, e.g., auth_alg and eap use a space separated
list of values without quotation marks. To allow these to be entered
from the interactive mode, change set_network command to allow more than
three arguments.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds description of the main changes from the forking of
hostap-1.git for 1.x releases to the current master branch snapshot.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 296a34f0c1 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 620c783753 modified
wpas_wps_ssid_wildcard_ok() prototype, but forgot to update the
non-WPS-build wrapper. Fix that to match with the new bss parameter
type and remove the now unused declaration of wpa_scan_res.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If separate group interfaces are used, the pending group interface got
removed unnecessarily when stopping find operations when accepting an
invitation to reinvoke the group in GO role. This resulted in the group
interfaces getting created twice. Avoid this unnecessary extra operation
by skipping removal of the pending interface in the reinvocation
sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
