Indicate DSCP Policy capability by including a WFA Capabilities element
containing the relevant bit set to 1 in the (Re)Association Request
frames when enabled by user.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse received DSCP Policy Request frames and send the
request details as control interface events.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This new vendor command aims to indicate the driver to enable the
monitor mode for an interface on which this command is issued. Once
enabled, the frames (both TX and RX) on this interface are sent to an
active coexisting monitor interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new attributes for supporting MBSSID multi groups notifications
to qca_wlan_vendor_attr_mbssid_tx_vdev_status
(QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
QCA_ROAM_REASON_USER_TRIGGER was wrongly documented as
QCA_ROAM_REASON_EXPLICIT_REQUEST, so correct it.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.
For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'
- Previous behavior: AP fallback to channel 100 using 20 MHz with
"No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
"VHT center channel 106 for 80 or 80+80 MHz bandwidth"
This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface support for configuring background scan related
parameters to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 45c3e72952 ("Add frequency to operating class determination
for 5 GHz 100..140") extends ieee80211_freq_to_channel_ext() with
knowledge of the operating classes for the 5 GHz channels 100..140.
Per "Table E-4 - Global operating classes" in IEEE Std 802.11-2020, 5
GHz channel 144 also maps to same operating classes, so update hostapd
code to reflect the change.
This issue is found when OCV enabled and 4-way-handshake failed due
to client OCI includes op_class 0 for channel 144. This showed
up in following manner in the debug log:
WPA: OCI KDE in EAPOL-Key - hexdump(len=9): dd 07 00 0f ac 0d 00 90 00
Error interpreting OCI: unrecognized opclass/channel pair (0/144)
Signed-off-by: Hu Wang <huw@codeaurora.org>
Enable support for P2P connection in 6 GHz with the channel width of 40
MHz, 80 MHz, and 160 MHz. The flag max_oper_chwidth is used to configure
the maximum channel width for P2P connection in 6 GHz with the commands
P2P_CONNECT, P2P_INVITE, and P2P_GROUP_ADD.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Current definition of wpas_p2p_get_ht40_mode() determines secondary
offset in the 5 GHz band. Enhance the functionality of this function to
determine offset to support 6 GHz channels also.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add a new attribute into qca_wlan_vendor_attr_ll_stats_results to
support getting interface time slicing duty cycle info.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11ax-2021 added channel 177 into global operating class 125
and consequently channel 173 in global operating class 126 (HT40+) and
channel 177 in global operating class 127 (HT40-).
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Skip the test of HE PHY capability bit "Support for a 40 MHz and 80 MHz
channel width" when starting an AP with a 20 MHz channel on the 5 GHz
band.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Add a QCA vendor attribute to configure the driver/firmware the allowed
bands for roaming by userpace. This attribute is also used to get the
configured roam bands from the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Generate an event on the control socket interface when a network is
added or removed. The event name CTRL-EVENT-NETWORK-<ADDED|REMOVED>
is followed by the network entry identifier. The event matches the
corresponding Network<Added|Removed> signal on the d-bus interface.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
==19798==ERROR: AddressSanitizer: heap-use-after-free on address 0x6110000663f8 at pc 0x55a2c485a232 bp 0x7ffeb42dcaf0 sp 0x7ffeb42dcae0
READ of size 8 at 0x6110000663f8 thread T0
Connect STA wlan0 to AP
#0 0x55a2c485a231 in ptksa_cache_add ../src/common/ptksa_cache.c:310
#1 0x55a2c4398045 in hostapd_store_ptksa ../src/ap/wpa_auth_glue.c:943
#2 0x55a2c4430980 in wpa_auth_store_ptksa ../src/ap/wpa_auth.c:232
#3 0x55a2c44578e1 in sm_WPA_PTK_PTKINITDONE_Enter ../src/ap/wpa_auth.c:3650
#4 0x55a2c44578e1 in sm_WPA_PTK_Step ../src/ap/wpa_auth.c:3798
#5 0x55a2c44578e1 in wpa_sm_step ../src/ap/wpa_auth.c:4437
#6 0x55a2c445d99d in wpa_receive ../src/ap/wpa_auth.c:1411
#7 0x55a2c43e7747 in ieee802_1x_receive ../src/ap/ieee802_1x.c:1118
#8 0x55a2c43bbf73 in hostapd_event_eapol_rx ../src/ap/drv_callbacks.c:1542
#9 0x55a2c43bbf73 in wpa_supplicant_event ../src/ap/drv_callbacks.c:1932
#10 0x55a2c466cb2d in drv_event_eapol_rx ../src/drivers/driver.h:6074
#11 0x55a2c466cb2d in nl80211_control_port_frame ../src/drivers/driver_nl80211_event.c:2822
#12 0x55a2c466cb2d in process_bss_event ../src/drivers/driver_nl80211_event.c:3194
#13 0x7feed9e90b9b in nl_cb_call ./include/netlink-private/netlink.h:145
#14 0x7feed9e90b9b in recvmsgs ./lib/nl.c:1006
#15 0x7feed9e90b9b in nl_recvmsgs_report ./lib/nl.c:1057
#16 0x7feed9e91058 in nl_recvmsgs ./lib/nl.c:1081
#17 0x55a2c45f2e8c in wpa_driver_nl80211_event_receive ../src/drivers/driver_nl80211.c:1782
#18 0x55a2c44b9afa in eloop_sock_table_dispatch ../src/utils/eloop.c:603
#19 0x55a2c44be122 in eloop_run ../src/utils/eloop.c:1228
#20 0x55a2c43360bf in hostapd_global_run /home/mbr/hostapd/hostapd/main.c:451
#21 0x55a2c43360bf in main /home/mbr/hostapd/hostapd/main.c:898
#22 0x7feed8ce20b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2)
#23 0x55a2c432f3fd in _start (/home/mbr/hostapd/hostapd/hostapd+0x9f23fd)
0x6110000663f8 is located 184 bytes inside of 216-byte region [0x611000066340,0x611000066418)
freed by thread T0 here:
#0 0x7feeda1477cf in __interceptor_free (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x10d7cf)
#1 0x55a2c44ce56b in os_free ../src/utils/os_unix.c:773
#2 0x55a2c451a986 in radius_msg_free ../src/radius/radius.c:137
#3 0x55a2c4527104 in radius_client_msg_free ../src/radius/radius_client.c:261
#4 0x55a2c452f53c in radius_client_list_add ../src/radius/radius_client.c:715
#5 0x55a2c452f53c in radius_client_send ../src/radius/radius_client.c:807
#6 0x55a2c453b24c in accounting_sta_report ../src/ap/accounting.c:352
#7 0x55a2c453d6e9 in accounting_sta_stop ../src/ap/accounting.c:384
#8 0x55a2c44190fd in ap_free_sta ../src/ap/sta_info.c:194
#9 0x55a2c4934530 in handle_deauth ../src/ap/ieee802_11.c:6035
#10 0x55a2c4934530 in ieee802_11_mgmt ../src/ap/ieee802_11.c:6399
#11 0x55a2c43bf114 in hostapd_mgmt_rx ../src/ap/drv_callbacks.c:1468
#12 0x55a2c43bf114 in wpa_supplicant_event ../src/ap/drv_callbacks.c:1912
#13 0x55a2c465faf7 in mlme_event_mgmt ../src/drivers/driver_nl80211_event.c:823
#14 0x55a2c4661774 in mlme_event ../src/drivers/driver_nl80211_event.c:1135
#15 0x55a2c466c43b in process_bss_event ../src/drivers/driver_nl80211_event.c:3177
#16 0x7feed9e90b9b in nl_cb_call ./include/netlink-private/netlink.h:145
#17 0x7feed9e90b9b in recvmsgs ./lib/nl.c:1006
#18 0x7feed9e90b9b in nl_recvmsgs_report ./lib/nl.c:1057
previously allocated by thread T0 here:
#0 0x7feeda147bc8 in malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x10dbc8)
#1 0x55a2c44cd387 in os_malloc ../src/utils/os_unix.c:715
#2 0x55a2c44ceb7f in os_zalloc ../src/utils/os_unix.c:779
#3 0x55a2c451a9f2 in radius_msg_new ../src/radius/radius.c:109
#4 0x55a2c4539a6e in accounting_msg ../src/ap/accounting.c:46
#5 0x55a2c453be15 in accounting_report_state ../src/ap/accounting.c:439
#6 0x55a2c453d91d in accounting_init ../src/ap/accounting.c:534
#7 0x55a2c4378952 in hostapd_setup_bss ../src/ap/hostapd.c:1333
#8 0x55a2c4382530 in hostapd_setup_interface_complete_sync ../src/ap/hostapd.c:2094
#9 0x55a2c4382815 in hostapd_setup_interface_complete ../src/ap/hostapd.c:2229
#10 0x55a2c4384100 in setup_interface2 ../src/ap/hostapd.c:1726
#11 0x55a2c4386b58 in setup_interface ../src/ap/hostapd.c:1628
#12 0x55a2c4386b58 in hostapd_setup_interface ../src/ap/hostapd.c:2318
#13 0x55a2c4387a57 in hostapd_enable_iface ../src/ap/hostapd.c:2730
#14 0x55a2c455d723 in hostapd_ctrl_iface_enable /home/mbr/hostapd/hostapd/ctrl_iface.c:1606
#15 0x55a2c455d723 in hostapd_ctrl_iface_receive_process /home/mbr/hostapd/hostapd/ctrl_iface.c:3607
#16 0x55a2c456821e in hostapd_ctrl_iface_receive /home/mbr/hostapd/hostapd/ctrl_iface.c:4018
#17 0x55a2c44b9afa in eloop_sock_table_dispatch ../src/utils/eloop.c:603
#18 0x55a2c44be122 in eloop_run ../src/utils/eloop.c:1228
#19 0x55a2c43360bf in hostapd_global_run /home/mbr/hostapd/hostapd/main.c:451
#20 0x55a2c43360bf in main /home/mbr/hostapd/hostapd/main.c:898
#21 0x7feed8ce20b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2)
SUMMARY: AddressSanitizer: heap-use-after-free ../src/common/ptksa_cache.c:310 in ptksa_cache_add
Shadow bytes around the buggy address:
0x0c2280004c20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0c2280004c30: 00 00 fa fa fa fa fa fa fa fa fa fa fa fa fa fa
0x0c2280004c40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0c2280004c50: 00 00 00 00 00 00 00 00 00 fa fa fa fa fa fa fa
0x0c2280004c60: fa fa fa fa fa fa fa fa fd fd fd fd fd fd fd fd
=>0x0c2280004c70: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd[fd]
0x0c2280004c80: fd fd fd fa fa fa fa fa fa fa fa fa fa fa fa fa
0x0c2280004c90: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
0x0c2280004ca0: fd fd fd fd fd fd fd fd fd fd fd fd fa fa fa fa
0x0c2280004cb0: fa fa fa fa fa fa fa fa fd fd fd fd fd fd fd fd
0x0c2280004cc0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
Shadow byte legend (one shadow byte represents 8 application bytes):
Addressable: 00
Partially addressable: 01 02 03 04 05 06 07
Heap left redzone: fa
Freed heap region: fd
Stack left redzone: f1
Stack mid redzone: f2
Stack right redzone: f3
Stack after return: f5
Stack use after scope: f8
Global redzone: f9
Global init order: f6
Poisoned by user: f7
Container overflow: fc
Array cookie: ac
Intra object redzone: bb
ASan internal: fe
Left alloca redzone: ca
Right alloca redzone: cb
Shadow gap: cc
==19798==ABORTING
Fixes: a4e3691616 ("WPA: Add PTKSA cache implementation")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add QCA new status vendor attribute
QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE
to indicate the TWT session termination due to power save
exit request from userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attribute to indicate the bandwidth to be used
for spectral scan operation:
- QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD to fetch thermal
statistics for different temperature levels from the driver to
userspace. The statistics will be stored in the driver/firmware for
predefined temperature levels and will be reported to userspace when
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD is sent with the command type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS.
The thermal statistics can be cleared from userspace by sending a
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD command with the type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Determine if the TDLS peer supports TDLS in 6 GHz band based on the HE 6
GHz Band Capabilities element received in the TDLS Setup Response frame.
Indicate the peer's HE 6 GHz capabilities to the driver through
sta_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attributes to configure the driver to enable/disable the
Broadcast TWT support and Rx Control Frame To MultiBSS support in HE
capabilities information field. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF
TWT attribute to use it in TWT setup command to pass TSF value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attribute to configure the driver to enable/disable
the BSS max idle period support. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use scan
request BSSID value in Probe Request frame RA(A1) for scan.
This attribute is used for testing purpose.
The driver saves this configuration and applies this setting to all user
space scan requests until the setting is cleared. If this configuration
is set, the driver uses the BSSID value from the scan request to set the
RA(A1) in the Probe Request frames during the scan, else the broadcast
address is set in the Probe Request frames RA(A1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend the previously 5 GHz specific 80 and 160 MHz channels helper
functions to support 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Introduce P2P 6 GHz band capable information in Device Capability
Bitmap of P2P Capability sub-attribute.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add QCA vendor interface to configure the driver which transport mode to
use for sending CFR data to userspace. Currently, relayfs and netlink
event modes are supported.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use Data or
Management frames for keep alive data. This attribute is used for
testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute to configure the driver to transmit the
Data frames with ER SU PPDU type format. This attribute is used
for testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS
to configure FT over DS to the driver/firmware.
Signed-off-by: Vinita S. Maloo<vmaloo@codeaurora.org>
Add QCA interface to specify the RSSI thresholds separately for candidate
APs from different bands.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Mention that for AP mode this attribute is required in
response for TWT SET, TWT GET, TWT SUSPEND, and TWT
TERMINATE. And is required in request for TWT GET, and
TWT TERMINATE.
For STA mode, the usage of this attribute remains unchanged.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
This moves the implementation closer to the current IEEE 802.11 standard
since B15 of Frame Control field was renamed to +HTC to match it newer
uses.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface for userspace to get information of usable
channels for different interface types from the driver/firmware.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Get the DPP Relay Controller context from the list of configured
Controllers based on the correct hostapd callback context. This is
needed to pick the correct hostapd interface for sending out the
response over air, e.g., when the same hostapd process controls a 2.4
GHz only and a 5 GHz only interface.
Signed-off-by: Disha Das <dishad@codeaurora.org>
The firmware rejects the TWT setup request when scan is in
progress. Extend enum qca_wlan_vendor_twt_status to represent new
reason code for it.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Define a new reason code in enum qca_wlan_vendor_hang_reason,
QCA_WLAN_TASKLET_CREDIT_LATENCY_DETECT, for tasklet/credit latency
detection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a QCA vendor command to configure the concurrent connection
policies when multiple STA interfaces are (getting) active.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add timeout to close incomplete DPP relay connections. This is needed to
avoid getting stuck with old entries that prevent new connections from
getting started.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This changes the Send-Confirm value for the first SAE Confirm message to
be 1 instead of 0 for all cases to match the design shown in IEEE Std
802.11-2020, Figure 12-4 (SAE finite state machine).
Sc is defined to be "the number of SAE Confirm messages that have been
sent" which is a bit vague on whether the current frame is included in
the count or not. However, the state machine is showing inc(Sc)
operation in all cases before the "2" event to build the Confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The 6 GHz band operating class 136 is defined to use 20 MHz bandwidth.
Return the value accordingly from center_idx_to_bw_6ghz() to cover this
special case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
It is more convenient to see the exact error in the debug log instead of
getting noted that something was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an attempt of making the code easier to understand for static
analyzers. The helper functions were already verifying that these IEs
are fully within the memory buffer, but that may not have been clear
enough for automated analysis.
Signed-off-by: Jouni Malinen <j@w1.fi>
BRCM vendor command used to trigger ACS scan. After ACS finished,
DHD driver will send results by event BRCM_VENDOR_EVENT_ACS.
Signed-off-by: Xinrui Sun <xinrui.sun@broadcom.com>
Determine if the TDLS peer is HE capable based on HE Capability element
received in the TDLS Setup Response frame. Indicate the peer's HE
capabilities to the driver through sta_add().
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware to use only
RU 242 tone for data frame transmission.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver with a specific BSS
max idle period value to advertise in (Re)Association Request frames.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The TX event for the next frame in the sequence might be received before
the TX status for the final GAS response frame is processed. This used
to result in the Config Result getting discarded and the negotiation not
completing successfully on the Configurator side.
Accept the Config Result message as an indication of the final GAS
response frame having went through fine even if the TX status has not
yet been processed to avoid this issue from a potential race condition
on kernel events.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add additional attributes for the QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO to get finer details on roaming
behavior, TSF out of sync count, and the latest TX rate, Rate Index used
for the transmission.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add definitions from IEEE Std 802.11ai-2016, 9.6.8.36 FILS discovery
frame format and extensions for the 6 GHz band from IEEE P802.11ax/D8.0.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
There are 2 HW modes with IEEE80211_MODE_A: one for the 5 GHz channels
and one for 6 GHz channels. Since hw_get_chan() checks all the
compatible hw modes, eventually, an incorrect hw mode is selected.
To fix this, add a function that checks if a specific mode supports
the requested frequency and if so use it as the current mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow HE MCS rate to be used for beacon transmission when the driver
advertises the support. The rate is specified with a new beacon_rate
option "he:<HE MCS>" in hostapd configuration.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use more accurate INTERWORKING_EXCLUDED for this. The actual event
prefix is not changed to remains compatible with external components
using this control interface event message.
Signed-off-by: Jouni Malinen <j@w1.fi>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Old gcc versions complain about signed/unsigned comparison in
dpp_rx_gas_resp(). Hide it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:
- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.
Add support for advertising the new capabilities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add PASN implementation to wpa_supplicant
1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.
The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.
The missing parts will be added in later patches.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In order to be able to perform secure LTF measurements, both the
initiator and the responder need to first derive TK and KDK and store
them, so they would later be available for the secure LTF negotiation.
Add a basic implementation of a PTKSA cache that stores derived TK/KDK
which can later be used for secure LTF negotiation, and add it to the
build configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add helper functions to construct a PASN Authentication frame and
validate its content, which are common to both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
1. Add a function to derive the PTK from a PMK and additional data.
2. Add a function to calculate the MIC for a PASN frames.
3. Add a function to compute the hash of an authentication frame body.
The above are built only in case that CONFIG_PASN is enabled at build
time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the fils_pmk_to_ptk() to also derive Key Derivation
Key (KDK) which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_r1_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Update the wpa_supplicant and hostapd configuration and the
corresponding WPA and WPA Auth state machine, to allow enabling of KDK
derivation. For now, use a testing parameter to control whether KDK is
derived.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication requires that group management cipher suite
would be set to 00-0F-AC:7 in the RSNE, so consider it as a valid
group management cipher and adjust the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for new channels 173 and 177 in the operating classes 125 to
130 as defined in draft IEEE P802.11ax/D8.0.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
The operating class 129 includes channels with a maximum bandwidth of
160 MHz with center frequency index 50 and 114. The previous definition
of operating class 129 considered the center frequency index as actual
channels resulting in incorrect channel setup for the operating class.
Fix the definition of operating class 129 to consider channels with the
center frequency index of 50 and 114.
Also update the comment that describes the channel selection for
operating 128, 129, and 130 which mentions wpas_p2p_allow_channel()
verifies the channels while wpas_p2p_verify_channel() takes care of it.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After sending DPP Auth Response, the Responder might not receive the
Auth Confirm either due to the Initiator not sending it or the reception
of the frame failing for some reason (e.g., Responder having already
left the negotiation channel). If this happens, following initiation
attempts would fail since the consecutive Auth Request would get
discarded since the previous authentication is still in progress.
Terminate DPP authentication on Responder, if no Auth Confirm is
received within one second of successfully sending Auth Response. This
allows the Responder to accept start of a new exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The response for the respective TWT operations can either be synchronous
or asynchronous (wherever specified). If synchronous, the response to
this operation is obtained in the corresponding vendor command reply to
the user space. For asynchronous case, the response is obtained as an
event with the same operation type.
Drivers shall support either of these modes but not both simultaneously.
The support for asynchronous mode is advertised through the new flag
QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If the driver does not
include this flag, it shall support synchronous mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
S1G beacons save a few bytes by not requiring the RSNE in beacon if RSN
BSS is configured. Handle this in wlantest by only clearing RSNE from
the BSS info if frame is a Probe Response frame.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
TWT nudge is a combination of suspend and resume in a single request.
Add TWT nudge operation and QCA vendor attributes to support
the TWT nudge request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
P2P usage in the 6 GHz band is not standardized yet by WFA. Disable P2P
operations in the 6 GHz band to avoid potential interop issues with
existing P2P devices in production. P2P operations in the 6 GHz band can
be reenabled later after defining standard ways to address potential
interop issues with existing P2P devices.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor specific feature capability
QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS to know if the device
supports concurrent network sessions on different Wi-Fi bands. This feature
capability is attributed to the hardware's capability to support the same
(e.g., DBS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO to
enable/disable full bandwidth UL MU-MIMO subfield in the HE PHY
capabilities information field for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The allocated memory pointed by the pem pointer was freed on an error
path without clearing the pointer to NULL before returning it from the
function. This could have resulted in use of freed memory in an error
case. Fix this by clearing the pointer so that the function returns NULL
properly in the case of this error.
Fixes: ace3723d98 ("DPP2: Enterprise provisioning (Enrollee)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP_CONFIGURATOR_ADD processing of the new ppkey parameter had a
copy-paste error in determining the correct length of this parameter.
Fix that by referencing the correct pointer.
Fixes: 9c1fbff074 ("DPP2: Generate a privacy protection key for Configurator")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for missing 6 GHz operating classes as defined in
IEEE P802.11ax/D7.0.
This is needed to avoid OCV failures on the 6 GHz band when the channel
width is larger than 20 MHz.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Previously only primary channel number used to calculate 6GHz operating
class in ieee80211_freq_to_channel_ext() and it is always giving 131
operating class. Fix this by mapping operating class using chanwidth and
sec_channel also.
This is needed to avoid OCV failures on the 6 GHz band when the channel
width is larger than 20 MHz.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
In theory, the EVP_PKEY_get0_EC_KEY() could fail, so verify that it
succeeds before using the pointer to get the group.
Fixes: 65e94351dc ("DPP2: Reconfig Authentication Request processing and Response generation")
Signed-off-by: Disha Das <dishad@codeaurora.org>
IANA assigned the TCP port 8908 for DPP, so update the implementation to
match the formal assignment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If SAE_CONFIG_PK is not defined and sae->pk isn't zero (which is
possible as it is controlled by the commit message status code),
sae_derive_keys() may end up deriving PMK and KCK from an
uninitialized array. Fix that.
Fixes: 6b9e99e571 ("SAE-PK: Extend SAE functionality for AP validation")
Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The connection process fails for several reasons and the status codes
defined in IEEE Std 802.11 do not cover the locally generated reason
codes. Add an attribute to QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor
sub command which can be used by the driver/firmware to report various
additional reason codes for connection failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows the privacyProtectionKey to be transferred to a new
Configurator similarly to the way c-sign-key is transferred.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use ppKey instead of C-sign-key to encrypted E-id to E'-id into Reconfig
Announcement frame on the Enrollee side.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Store the received privacy protection key from Connector into
wpa_supplicant network profile and indicate it through the control
interface similarly to C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This provides the new privacy protection key to the Enrollee so that
this can be used to protect E-id in Reconfig Announcement frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Generate a new key for Configurator. This is either generated
automatically for the specified curve or provided from external source
with the new ppkey=<val> argument similarly to the way c-sign-key was
previously generated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
We don't really need to duplicate more of this, so just
move the lib.rules include to the end and do more of the
stuff that's common anyway there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Derive the library name from the directory name, and let each
library Makefile only declare the objects that are needed.
This reduces duplicate code for the ar call. While at it, also
pretty-print that call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is something I hadn't previously done, but there are
cases where it's needed, e.g., building 'wlantest' and then
one of the tests/fuzzing/*/ projects, they use a different
configuration (fuzzing vs. not fuzzing).
Perhaps more importantly, this gets rid of the last thing
that was dumped into the source directories, apart from
the binaries themselves.
Note that due to the use of thin archives, this required
building with absolute paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of building in the source tree, put most object
files into the build/ folder at the root, and put each
thing that's being built into a separate folder.
This then allows us to build hostapd and wpa_supplicant
(or other combinations) without "make clean" inbetween.
For the tests keep the objects in place for now (and to
do that, add the build rule) so that we don't have to
rewrite all of that with $(call BUILDOBJS,...) which is
just noise there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define a control event with bootstrap id, frame source, frequency, and
chirp hash for receipt of Presence Announcement (chirp) frames.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
DPP tech spec was modified to use v1(0) instead of v2(1) for the
OneAsymmetricKey in the Configurator backup structure to match the
description in RFC 5958 Section 2 which indicates v2 to be used when any
items tagged as version 2 are included. No such items are actually
included in this case, so v1 should be used instead.
Change OneAsymmetricKey generation to use v1(0) instead of v2(1) and
parsing to accept either version to be used. This is not backwards
compatible with the earlier implementation which requires v2(1) when
parsing the received value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
crypto_bignum_init_set() might fail in case of memory allocation
failures. These two cases within sswu() did not handle that properly,
i.e., a memory allocation failure could have resulted in dereferencing a
NULL pointer. Check the return value before proceeding to fix this.
Fixes: aeb022f8e5 ("SAE: Implement hash-to-element PT/PWE crypto routines")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS that represents the
triggers for which the scan scheme from enum qca_roam_scan_scheme has to
be applied.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends a new status code to indicate an already suspended
TWT session. Update the status code enum to represent this state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11 specifies that the Operating Classes field terminates
immediately before the OneHundredAndThirty Delimiter (i.e., an octet
with value 130). Move the operating class value 130 last in the global
op_class array so that it gets added as the last entry into the
Supported Operating Clases element and the 6 GHz operating class is
parsed in that element by implementation that stop at the assumed
OneHundredAndThirty Delimiter.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes to enum qca_vendor_attr_roam_control to
control the roam behavior through QCA_NL80211_VENDOR_SUBCMD_ROAM and
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attributes to get thermal level from the driver. The
driver may return thermal level when userpace requests, or send a
thermal event when thermal level changes.
Signed-off-by: Hu Wang <huw@codeaurora.org>
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This was changed in the protocol design to include nonce from both
devices, so update implementation to match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was changed in the protocol design to allow ke derivation to use
E-nonce, so update implementation to match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This change adds QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS,
and enum for qca_wlan_vendor_attr_mbssid_tx_vdev_status to notify
Tx VDEV status.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new vendor attribute for GPIO configuration. In addition, document
the previously defined attributes.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
These were not really used anymore since the AP/Relay case did not set
msg_ctx or process_conf_obj in the global DPP context. Get the
appropriate pointers more directly from the more specific data
structures instead and remove these global values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd support for DPP Controller to cover the DPP_CONTROLLER_*
cases that were previously implemented only in wpa_supplicant. This
allows hostapd/AP to be provisioned using DPP over TCP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Firmware statistics are received in the driver as opaque data. The host
target needs to send this opaque data to userspace wifistats
application. This new event is used to transfer this opaque data to the
application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to configure the driver/firmware to
ignore SA Query timeout. If this configuration is enabled the
driver/firmware shall not send Deauthentication frame when SA Query
times out. This is required to support STA testbed role.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
These vendor attributes for FT/OCV/SAE testing can be configured only
when the STA is in connected state. Update the documentation of the
attributes to reflect the same.
Fixes: 18f3f99ac4 ("Add vendor attributes to configure testing functionality for FT/OCV/SAE")
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to get number of MIC errors, missing MME incidents, and
packet replay incidents observed while using IGTK/BIGTK keys when PMF
and/or beacon protection features are enabled.
These counters are applicable only for STA mode and can be fetched
through the QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse the (Re)Association Response frames to check if the
AP has accepted/declined the MSCS request in response to the
corresponding (Re)Association Request frame. AP indicates the result by
setting it in the optional MSCS Status subelement of MSCS Descriptor
element in (Re)Association Response frame.
This MSCS Status subelement is defined in the process of being added
into P802.11-REVmd/D4.0 (11-20-0516-17-000m-cr-mscs-and-cid4158).
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to receive and process MSCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID
to update the new SSID in hostapd. NL80211_ATTR_SSID is used to encapsulate
the new SSID.
Signed-off-by: Pooventhiran G <pooventh@codeaurora.org>
Currently the driver/firmware indicates CCA busy time which includes own
TX and RX time and as such, does not allow the CCA busy time due to
other nodes to be computed. Add separate statistics to indicate own
radio TX time and own radio RX time to facilitate userspace applications
to compute CCA busy time because of traffic unintended to this device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
All QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* attributes are also nested
within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO, not only
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO* attributes in the current
implementation. Fix QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO documentation
accordingly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit does the following enhancements to the TWT interface:
Corrects the documentation for QCA_WLAN_TWT_SUSPEND and
QCA_WLAN_TWT_TERMINATE. Specifies that these operations carry the
parameters obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. This
interface is very recently introduced and missed to document the same.
There are no user space or driver components using this interface yet.
Hence, enhancing/modifying the interface.
Corrects the documentation for
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION. Mentions that the units it
represent is a multiple of 256 microseconds rather than a TU. The host
driver always interpreted this as an unit in 256 microseconds and there
are no user space implementations that are impacted with this change in
the unit. Hence, modifying the documentation.
Introduces QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT_SIZE, which is
similar to that of QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT, but carries
an offset/data of u32 size.
Introduces MAC_ADDR attribute to represent the peer for the TWT setup
and resume operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the listed unknown operating class/channel number pairs need to be
ignored, that should be done in a manner than prevents the parsed
bootstrapping info from being used as if it had no channel list (i.e.,
allowing any channel) if there are no known operating class/channel
number pairs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend DPP authentication session search for the DPP_QR_CODE command to
cover the ongoing exchanges in Controller/Responder.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The case where mutual authentication with QR Code bootstrapping is used
with scanning of the QR Code during the exchange resulted in the
Controller closing the TCP socket too early. Fix this by leaving the
socket open while waiting for the full Authentication Response message.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend the DPP_CONTROLLER_START command to accept the optional qr=mutual
parameter similarly to the DPP_LISTEN case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to configure the number of TX chains and the number of RX
chains to be used during a connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend dpp_control_get_auth() to find the ongoing session for enterprise
credential provisioning in cases where the Controller/Configurator
initiated the exchange. Only the other direction was supported
previously.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an encrypted Enrollee identifier into Reconfig Announcement frames
and decrypt that on the Configurator side. The actual E-id value is
currently not used for anything, but it can be used in the future to
provide better control over reconfiguration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was added to the protocol design to support cases where the
C-sign-key uses a different group than the netAccessKey. The Enrollee
now indicates its netAccessKey group in Reconfig Announcement and the
Configurator builds it own reconfig Connector using that group instead
of the group used for the C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce additional attributes for the TWT response parameters from the
host driver. Also, add ATTR_TWT_RESUME_FLOW_ID for TWT Resume request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the SAE-PK implementation to match the changes in the protocol
design:
- allow only Sec values 3 and 5 and encode this as a single bit field
with multiple copies
- add a checksum character
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The documentation for the QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
attribute had incorrectly specified the value of 0 (corresponding to BE)
to disable the QoS upgrade. BK (1) is a lower priority AC compared to BE
and if BE is used to disable the upgrade, there would be no possibility
for configured UDP AC upgrade to replace BK-from-DSCP with BE. Thus,
correct this by specifying that the value of BK (1) is used to disable
this UDP AC upgrade.
Fixes: ebd5e764f9 ("Vendor attribute to configure QoS/AC upgrade for UDP frames")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sae_check_confirm_pk() and sae_write_confirm_pk() were using different
checks for determining whether SAE-PK was used. It was apparently
possible to miss the checks in sae_write_confirm_pk() in some AP cases
where SAE H2E is being used. Fix this by checking sae->pk in the
write-confirm case similarly to the way this was done in check-confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Debug logs did not make it clear whether the failure happens when
checking a received SAE confirm or when writing own SAE confirm. Those
cases have different checks on when to go through SAE-PK processing, so
it is useful to make this part clear in the debug log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
to configure access category override for UDP frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor command to get the currently enabled band(s)
through QCA_NL80211_VENDOR_SUBCMD_GETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Also introduce a new attribute QCA_WLAN_VENDOR_ATTR_SETBAND_MASK to
carry this new bitmask enum. This attribute shall consider the bitmask
combinations to define the respective band combinations and substitutes
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. The old attribute use remains same
as before.
In addition, document the previously undocumented, but defined,
QCA_NL80211_VENDOR_SUBCMD_SETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
40/80 MHz bandwidth setting was being rejected due to incorrect sanity
check on the channel index. Fix that for the bandwidths larger than 20
MHz.
Fixes: d7c2c5c98c ("AP: Add initial support for 6 GHz band")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
The 0..3 value decoded from the password was not incremented to the
actual 2..5 range for Sec. This resulted in not properly detecting the
minimum password length.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbering/center frequencies was changed in IEEE
P802.11ax/D6.1. The center frequencies of the channels were shifted by
10 MHz. Also, a new operating class 136 was defined with a single
channel 2. Add required support to change the channelization as per IEEE
P802.11ax/D6.1.
Signed-off-by: Wu Gao<wugao@codeaurora.org>
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add events for within-ESS reassociation. This allows us to monitor roam
events, both skipped and allowed, in tests.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
This allows the DPP_CA_SET command to be targeting a specific DPP-CST
event in cases where the Configurator did not receive the bootstrapping
information for the peer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
