Use a helper function for this and add checks for number of test cases
that were missing this. This gets rid of undesired FAIL results
(converts them to SKIP) for test runs where the station do not support
SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces the vendor event
QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT.
Host drivers can request user space application to set SAR power
limits with this event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to set thermal level to the driver from
userspace. The driver/firmware takes actions requested by userspace to
mitigate high temperature such as throttling TX etc. The driver may
choose the level of throttling and other actions for various thermal
levels set by userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround=1 network parameter can be used
to enable older behavior mainly for testing purposes. There is no impact
to group 19 behavior, but if enabled, this will make group 20 and 21
cases use SHA256-based PTK derivation which will not work with the
updated OWE implementation on the AP side.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround parameter can be used to enable
workaround for interoperability with stations that use SHA256 with
groups 20 and 21. By default, only the appropriate hash function is
accepted. When workaround is enabled (owe_ptk_workaround=1), the
appropriate hash function is tried first and if that fails, SHA256-based
PTK derivation is attempted. This workaround can result in reduced
security for groups 20 and 21, but is required for interoperability with
older implementations. There is no impact to group 19 behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previous implementation was hardcoding use of SHA256 PMK-to-PTK
derivation for all groups. Replace that with hash algorithm selection
based on the length of the prime similarly to the way this was done for
other derivation steps in OWE.
This breaks backwards compatibility when using group 20 or 21; group 19
behavior remains same.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This has nothing to do with OWE and parsing of this value was not
supposed to be within an ifdef CONFIG_OWE block.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Explicitly clear cfg80211 scan cache to avoid issues with old BSS
entries from previous test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous commit had a rebasing issue that ended up covering only the
center_segment0 != 0 case. These were supposed to apply for all 6 GHz
band cases.
Fixes: 0bfc04b8d0 ("Do not enable HT/VHT when operating in 6 GHz band")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to be stored
in a separate hw_features set (but with same mode
HOSTAPD_MODE_IEEE80211A) due to possibility of different HT/VHT/HE
capabilities being available between the 5 GHz and 6 GHz bands.
Iterate through all hw_features sets and check and match the band of
channel supported by the hw_features set while getting the hw_features
set in get_mode(). This allows both the 5 GHz and 6 GHz channels to be
found and correct capabilities to be used in cases where the driver
reports different capability values between 5 and 6 GHz channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Users might be tempted to try ap_scan=0 for offloading scan,
ap_selection and, WPA to driver. Update the text to reflect that this is
deprecated.
Jouni confirmed deprecation in
https://www.spinics.net/lists/hostap/msg06482.html
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.com>
The previously used timeout of two seconds did not allow more than a
single scan attempt and that could fail every now and then. Make these
more robust by increasing the timeout to 10 seconds which allows another
scan attempt to be completed similarly to the most non-sigma_dut test
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.
See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE. Since wpa_supplicant and mac80211
do not yet support SAE H2E in mesh, Password Identifier cannot be used
in mesh cases. Remove the test cases that verified this behavior for now
to allow H2E to be required per updated REVmd definition. These test
cases will be restored once H2E is fully functionality in mesh cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This BSS membership selector has impact only for SAE functionality, so
ignore it when configured not to use SAE. This allows WPA-PSK connection
to and AP that advertises WPA-PSK and SAE while requiring H2E for SAE.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow running without curses, in which case the log is simply written to
stdout instead of a file. This is useful for automated (but parallel)
testing. Note that in most cases, you'd want to specify --debug, and so
I added a .rstrip() there on the lines to clean that up a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some things in bfd.h that we use were renamed, and in the case of
bfd_get_section_vma() a parameter was dropped. Work around this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for EAP method prefix in the anonymous identity
used during EAP-SIM/AKA/AKA' authentication when encrypted IMSI
is used. The prefix is a single character that indicates which
EAP method is required by the client.
Signed-off-by: Hai Shalom <haishalom@google.com>
Some of the sigma_dut test cases were not yet using try/finally to
ensure stop_sigma_dut() gets called. That could result in not logging
all failure reasons in the log and getting stuck with being unable to
start new sigma_dut processes after failed test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no point in having to enable this separately for each test case
since the debug details are always useful if something fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes logs easier to understand and this may also help in running
over buffer space and getting stuck with sigma_dut termination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Based on the now documented seg0/seg1 values from offloaded ACS, there
is a mismatch between the driver interface and internal hostapd use.
The value of segment0 field in ACS results is the index of the channel
center frequency for 20 MHz, 40 MHz, and 80M Hz channels. The value is
the center frequency index of the primary 80 MHz segment for 160 MHz and
80+80 MHz channels.
The value of segment1 field in ACS results is zero for 20 MHz, 40 MHz,
and 80 MHz channels. The value is the index of the channel center
frequency for 160 MHz channels and the center frequency index of the
secondary 80 MHz segment for 80+80 MHz channels.
However, in struct hostapd_config, for 160 MHz channels, the value of
the segment0 field is the index of the channel center frequency of 160
MHz channel and the value of the segment1 field is zero. Map the values
from ACS event into hostapd_config fields accordingly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the documentation with values to be sent for seg0 and seg1 fields
in external ACS result event for 20 MHz, 40 MHz, 80 MHz, 160 MHz, and
80+80 MHz channels. These values match the changes done to definitions
of seg0 and seg1 fields in the IEEE 802.11 standard.
This vendor command had not previously been documented in this level of
detail and had not actually been used for the only case that could have
two different interpretation (160 MHz) based on which version of IEEE
802.11 standard is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Channel Width field value is 0 for 20 MHz, 1 for 40 MHz, 2 for 80
MHz, and 3 for both 160 MHz and 80+80 MHz channels. The 80+80 MHz case
was not addressed previously correctly since it cannot be derived from
seg0 only.
The Channel Center Frequency Segment 0 field value is the index of
channel center frequency for 20 MHz, 40 MHz, and 80 MHz channels. The
value is the center frequency index of the primary 80 MHz segment for
160 MHz and 80+80 MHz channels.
The Channel Center Frequency Segment 1 field value is zero for 20 MHz,
40 MHz, and 80 MHz channels. The value is the index of the channel
center frequency for 160 MHz channel and the center frequency index of
the secondary 80 MHz segment for 80+80 MHz channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the dummy hostapd_hw_mode_txt() wrapper return "UNKNOWN" instead of
NULL to avoid a warning from a debug printf using %s with NULL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Current Python versions have no os.sleep(), use time.sleep() instead.
module 'os' has no attribute 'sleep'
Traceback (most recent call last):
File "./run-tests.py", line 521, in main
t(dev, apdev)
File "/home/mtheil/hostap/tests/hwsim/test_pmksa_cache.py", line 356, in test_pmksa_cache_expiration
hapd.wait_ptkinitdone(dev[0].own_addr())
File "/home/mtheil/hostap/tests/hwsim/hostapd.py", line 282, in wait_ptkinitdone
os.sleep(0.1)
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This is the function that actually uses the parameters, so pass the full
parameter struct to it instead of hiding the struct from it in the
simple wrapper.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the driver supports VLAN offload mechanism with a single netdev, use
that instead of separate per-VLAN netdevs.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Add indication for driver VLAN offload capability and configuration of
the VLAN ID to the driver.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This makes it more convenient to add, remove, and modify the parameters
without always having to update every single driver_*.c implementation
of this callback function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sae_confirm_immediate=2 can now be used in CONFIG_TESTING_OPTIONS=y
builds to minimize the latency between SAE Commit and SAE Confirm by
postponing transmission of SAE Commit until the SAE Confirm frame is
generated. This does not have significant impact, but can get the frames
tiny bit closer to each other over the air to increase testing coverage.
The only difference between sae_confirm_immediate 1 and 2 is in the
former deriving KCK, PMK, PMKID, and CN between transmission of the
frames (i.e., a small number of hash operations).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a channel list changed event is received after a scan and before
selecting a BSS for connection, a BSS found on a now disabled channel
may get selected for connection. The connect request issued with the BSS
found on a disabled channel is rejected by cfg80211. Filter out the BSSs
found on disabled channels and select from the other BSSs found on
enabled channels to avoid unnecessary connection attempts that are bound
to fail.
The channel list information will be updated by the driver in cases like
country code update, disabling/enabling specific bands, etc. which can
occur between the scan and connection attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Correct the check for presence of
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL attribute before using it
while processing acs_result event.
Fixes: 857d94225a ("Extend offloaded ACS QCA vendor command to support VHT")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The digestmod argument also exists in earlier Python versions,
version 3.8 does not set a default argument anymore.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
