Add the following vendor attributes under the enum
qca_wlan_vendor_attr_spectral_scan to support the configuration of
Spectral DMA debug.
1. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG
Enable/disable debug of the Spectral DMA ring
2. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG
Enable/disable debug of the Spectral DMA buffers
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SIM-based EAP authentication with IMSI encryption requires a special EAP
Identity response: anonymous@realm. Then the server sends AKA-Identity
request which is answered with the encrypted IMSI. Add logic that
indicates if the special anonymous identity is used. Otherwise, this
field is used for storing the pseudonym.
Test: Connect to Carrier Wi-Fi, verify correct behavior from captures
Test: Connect to non IMSI encrypted EAP-AKA AP, verify pseudonym usage
Signed-off-by: Hai Shalom <haishalom@google.com>
External auth status to the driver includes the PMKID derived as part of
SAE authentication, but this is not valid if PMKSA caching is disabled.
Drivers might not be expecting PMKID when it is not valid. Do not send
the PMKID to the driver in such cases.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
A driver that uses internal AP SME may need to be able to use the
external_auth status operation in station mode, so do not skip this
solely based on drv->device_ap_sme; instead, use that condition only
when operating in AP mode.
Fix external_auth status in non SME case.
Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
With radio work design, send Action frame request will be queued and
wait for p2p-scan to finish, so there is no need to delay send_action.
This change revisits the logic (added before the radio work framework)
in below commits:
3f9285f P2P: Delay send_action call if p2p_scan is in progress
f44ae20 P2P: Drop pending TX frame on new p2p_connect
9d562b7 P2P: Add p2p_unauthorize command
63a965c P2P: Fix after_scan_tx processing during ongoing operations
9a58e52 P2PS: Callback to create pending group after sending PD Response
3433721 P2P: Continue p2p_find after sending non-success Invitation Response
Signed-off-by: Hu Wang <huw@codeaurora.org>
In case the current channel has regulatory WMM limitations, take them
into account when filling the WMM element. Also check if the new WMM
element is different from the previous one and if so change the
parameter_set_count to imply stations to look into it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
In previous versions the device was allowed by ETSI to implement
802.11 channel access mechanism based on a set of priority classes
which are taken from 802.11. According of the new standard there
might be some exceptions which require ETSI countries to follow
more restrictive rules. In such a case the AP's wmm IE need to
comply with ETSI limitation. To be able to do so the regulatory
domain passes the new limitation values if needed.
Implement this, by storing it and use it to calculate the new
WMM parameters.
This commit adds determination of regulator limitations to
NL80211_CMD_GET_WIPHY processing so that the information is available
for upper layer implementation to use later when constructing WMM
element.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add support for injecting frames to a given mesh peer, bypassing the
mpath table lookup using PROBE_MESH_LINK command. This helps to send
data frames over unexercised direct mesh path, which is not selected as
next_hop node. This can be helpful in measuring link metrics.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In the case of the ap_csa_disable test, I frequently see
failures due to the kernel *not* having switched, but the
CSA-STARTED event having been processed, and thus the
frequency having been updated already.
This is wrong at least for AP mode, the frequency we store
for this case internally in nl80211 should only be updated
when the channel switch completes, otherwise we end up in
a situation where the switch is aborted and the kernel is
thus on the old channel, but the internal information has
been updated and every subsequent mgmt-frame TX fails due
to being tagged with the wrong channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
GnuTLS backend already accepts CA cert blobs in both DER and PEM
formats. Implement similar trial-and-error handling in OpenSSL backend.
Signed-off-by: Santtu Lakkala <santtu.lakkala@jolla.com>
When a new station is added, let it have some supported rates
(they're empty without this change), using the basic rates
that it must support to connect.
This, together with the kernel-side changes for client-side,
lets us finish the complete auth/assoc handshake with higher
rates than the mandatory ones, without any further config.
However, the downside to this is that a broken station that
doesn't check the basic rates are supported before it tries
to connect will possibly not get any response to its auth
frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Set operating channel bandwidth and center frequencies using the same
attributes for VHT and HE.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The PPE Thresholds information in the end of the HE Capabilities element
is optional and of variable length. struct he_ppe_threshold was not
really used correctly for encoding this, so remove it and just reserve
enough space for the information.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This is used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Bandwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
oper_chwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bandwidth values are shared between VHT and HE mode so remove the
VHT specific prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These bits might be set by the capabilities read from the kernel, so
mask them out if beamforming is not enabled in the local configuration.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This copying attempt was added incorrectly since that element is never
actually present in (Re)Association Request frames. It is only valid to
copy that element from the mesh peering frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 8.3.0 was apparently clever enough to optimize away the previously
used os_memset() to explicitly clear a stack buffer that contains keys
when that clearing happened just before returning from the function.
Since memset_s() is not exactly portable (or commonly available yet..),
use a less robust mechanism that is still pretty likely to prevent
current compilers from optimizing the explicit clearing of the memory
away.
Signed-off-by: Jouni Malinen <j@w1.fi>
Initialize auth_sock and acct_sock to -1 to avoid radius_server_deinit()
attempting to close fd=0 if anything fails in setting up the RADIUS
server.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Session-Id derivation for EAP-AKA in RFC 5247 only explained how the
Session-Id is derived for regular authentication. Jouni reported it as
an errata with text explaining how to derive it during fast
reauthentication.
This patch now exports the Session-Id for EAP-AKA during fast
reauthentication based on this Session-Id = 0x17 || NONCE_S || MAC
construction.
Also documented by Alan Dekok in draft-dekok-emu-eap-session-id.
Signed-off-by: Mohit Sethi <mohit.sethi@aalto.fi>
The Session-Id derivation for EAP-SIM in RFC 5247 only explained how the
Session-Id is derived for regular authentication. Jouni reported it as
an errata with text explaining how to derive it during fast
reauthentication.
This patch now exports the Session-Id for EAP-SIM during fast
reauthentication based on this Session-Id = 0x12 || NONCE_S || MAC
construction.
Signed-off-by: Mohit Sethi <mohit.sethi@aalto.fi>
The rcons[] and Td4s[] array values need to be type cast explicitly to
u32 for the left shift 24 operation to be defined due to the implicit
conversion to int not handling the case where MSB would become 1 without
depending on UB.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14929
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The IE header length check was off-by-one and that could allow the loop
to read one octet beyond the end of the buffer before breaking out in
the second check.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14927
Fixes: 0a66ce3c49 ("WNM: Add support for SSID List element matching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The bootstrapping URI format for DPP was extended during protocol design
to allow a list of channels without having to repeat the same operating
class information for each channel. That change was not included in the
initial implementation of the parser and a channel-list like
"C:81/1,6,11" would not be understood correctly (i.e., only the longer
"C:81/1,81/6,81/11" form would have been parsed correctly).
Fix this by extending the parser to accept both the shorter and longer
form for a list of channels within a single operating class.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11ai-2016 requires the FILS STA to do this check, but this
was missing from the initial implementation. The AP side behavior was
not described properly in 802.11ai due to a missing change in the
(Re)Association Response frame format tables which has resulted in some
deployed devices not including the RSNE.
For now, use an interoperability workaround to ignore the missing RSNE
and only check the payload of the element if it is present in the
protected frame. In other words, enforce this validation step only with
an AP that implements FILS authentication as described in REVmd while
allowing older implementations to skip this check (and the protection
against downgrade attacks). This workaround may be removed in the future
if it is determined that most deployed APs can be upgraded to add RSNE
into the (Re)Association Response frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This AP behavior was missing from IEEE Std 802.11ai-2016, but it is
needed for the RSNE validation to work correctly and for a FILS STA to
be able to perform the mandatory check for RSNE matching when processing
the (Re)Association Response frame (as described in 802.11ai). REVmd
will be updating the standard to cover this AP case, so prepare the
implementation to match that. Without this, a FILS STA might reject
association whenever using FILS authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If OCSP_resp_find_status() fails with the first OCSP_CERTID, the
generation of the second OCSP_CERTID ended up leaking memory. Fix this
by freeing the previously allocated OCSP_CERTID on that code path.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not allow auth->own_protocol_key to be overridden without having
freed the previously stored key in case a test sequence in
dpp_proto_auth_conf_replaced_by_resp is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
