Commit graph

3172 commits

Author SHA1 Message Date
Jouni Malinen
8266e6c6b4 HS 2.0: Try to use same BSS entry for storing GAS results
Commit 17b8995cf5 ('Interworking: Try to
use same BSS entry for storing GAS results') added a mechanism to try to
pair GAS request and response to a single BSS entry to cover cases where
multiple BSS entries may exists for the same BSSID. However, that commit
did not cover the Hotspot 2.0 ANQP elements. Extend this mechanism to
all ANQP elements. This can help in cases where information in the
Hotspot 2.0 specific ANQP elements got lost if a hidden SSID or some
other reason of duplicated BSS entries was present while doing ANQP
fetches.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 17:47:32 +02:00
Jouni Malinen
6c69991382 Make wpa_supplicant FLUSH command more likely to clear all BSS entries
Move the wpa_bss_flush() call to the end of the function to allow any
pending user of a BSS entry to be cleared before removing the unused
entries. There were number of cases where BSS entries could have been
left in the list and this resulted in some hwsim test failures.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 15:39:48 +02:00
Jouni Malinen
2dbe63ad53 Write reason for scan only_new_results into debug log
This can be helpful in figuring out why the driver was requested to
flush its scan results prior to starting a new scan.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 13:54:16 +02:00
Jouni Malinen
242b83a380 eapol_test: Fix cert_cb() function arguments
altsubject[] was added here, but the callback implementation in
eapol_test.c was forgotten from the commit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 02:24:00 +02:00
Jouni Malinen
a8826b1848 Interworking: Avoid busy loop in scan result mismatch corner cases
It was possible for interworking_find_network_match() to find a possible
BSS match in a case where more thorough checks in
wpa_supplicant_select_bss() reject network. This itself is fine, in
general, but when combined with wpa_supplicant_fast_associate()
optimization and auto_interworking=1, this resulted in a busy loop of up
to five seconds and a possible stack overflow due to recursion in that
loop.

Fix this by limiting the Interworking wpa_supplicant_fast_associate()
call to be used only once per scan iteration, so that new scan
operations can be completed before going through the scan results again.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 01:52:07 +02:00
Jouni Malinen
edd5939a26 Interworking: Start ANQP fetch from eloop callback
Reduce maximum stack use by starting next ANQP fetch operation from an
eloop callback rather than calling interworking_next_anqp_fetch()
directly from interworking_start_fetch_anqp(). This avoids issues that
could potentially make the process run out of stack if long loops of
ANQP operations are executed in cases where automatic Interworking
network selection is used and scan results do not have a full match for
a network.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 01:51:47 +02:00
Jouni Malinen
783b2a977f Interworking: Fix INTERWORKING_CONNECT with zero-length SSID BSS entry
For Interworking connection to work, the SSID of the selected BSS needs
to be known to be able to associate with the AP. It was possible for the
scan results to include two BSS entries matching the BSSID when an
earlier scan with that AP has shown a hidden SSID configuration (e.g.,
when running hwsim test cases, but at least in theory, this could happen
with real use cases as well). When that happened, the incorrect BSS
entry may not have included RSN configuration and as such, it would get
rejected for Interworking connection.

Fix this by confirming that the selected BSS entry has a real SSID. If
not, try to find another BSS entry matching the same BSSID and use that,
if found with an SSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-15 12:24:18 +02:00
Jouni Malinen
cebee30f31 Add domain_match network profile parameter
This is similar with domain_suffix_match, but required a full match of
the domain name rather than allowing suffix match (subdomains) or
wildcard certificates.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 15:45:18 +02:00
Jouni Malinen
d07d3fbda2 Add peer certificate alt subject name information to EAP events
A new "CTRL-EVENT-EAP-PEER-ALT depth=<i> <alt name>" event is now used
to provide information about server certificate chain alternative
subject names for upper layers, e.g., to make it easier to configure
constraints on the server certificate. For example:
CTRL-EVENT-EAP-PEER-ALT depth=0 DNS:server.example.com

Currently, this includes DNS, EMAIL, and URI components from the
certificates. Similar information is priovided to D-Bus Certification
signal in the new altsubject argument which is a string array of these
items.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 15:45:18 +02:00
Jouni Malinen
98a4cd447e D-Bus: Clear cached EAP data on network profile changes
This makes D-Bus network profile Set(Properties) clear cached EAP data
similarly to how SET_NETWORK does for control interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 13:24:09 +02:00
Jouni Malinen
483dd6a5e0 Include peer certificate always in EAP events
This makes it easier for upper layer applications to get information
regarding the server certificate without having to use a special
certificate probing connection. This provides both the SHA256 hash of
the certificate (to be used with ca_cert="hash://server/sha256/<hash>",
if desired) and the full DER encoded X.509 certificate so that upper
layer applications can parse and display the certificate easily or
extract fields from it for purposes like configuring an altsubject_match
or domain_suffix_match.

The old behavior can be configured by adding cert_in_cb=0 to
wpa_supplicant configuration file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 12:24:52 +02:00
Jouni Malinen
d29fa3a767 Extend VENDOR_ELEM parameters to cover non-P2P Association Request
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-14 01:12:56 +02:00
Jouni Malinen
cf08e9b1f4 Add MESH to modes capabilities
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports mesh.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
db5adfe777 Add SAE to auth_alg capabilities
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports SAE.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
a16514516b Add "GET tls_library" to provide information on TLS library and version
This new wpa_supplicant and hostapd control interface command can be
used to determine which TLS library is used in the build and what is the
version of that library.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
b09baf37cf Work around Windows build issues
At least MinGW did not have ENOTCONN, EOPNOTSUPP, ECANCELED, so define
these to allow the build to go through.
wpas_rrm_send_neighbor_rep_request() is not really used on Windows, so
the exact error code values do not make any difference here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:58:10 +02:00
Jouni Malinen
0b402479bf Remove Network Security Service (NSS) support
NSS as a TLS/crypto library alternative was never completed and this
barely functional code does not even build with the current NSS version.
Taken into account that there has not been much interest in working on
this crypto wrapper over the years, it is better to just remove this
code rather than try to get it into somewhat more functional state.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:58:10 +02:00
Jouni Malinen
e24aef10cf Fix a typo in domain_suffix_match documentation
Spell SubjectName correctly.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:27:01 +02:00
Jouni Malinen
394b54732e Improve subject_match and domain_suffix_match documentation
These were already covered in both README-HS20 for credentials and in
header files for developers' documentation, but the copy in
wpa_supplicant.conf did not include all the details. In addition, add a
clearer note pointing at subject_match not being suitable for suffix
matching domain names; domain_suffix_match must be used for that.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:27:01 +02:00
Stefan Tomanek
79cd993a62 Add address masks to BSSID lists
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).

This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Stefan Tomanek
b83e455451 Add network specific BSSID black and white lists
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.

This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Stefan Tomanek
b3d6a0a825 Add generic parser for MAC address lists
This change generalizes the code used for parsing the configuration
option 'p2p_client_list' and makes it suitable to use it in other
contexts.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Jouni Malinen
6dfc55723d Remove mesh_ht_mode network block parameter
There should not be a mesh-specific mechanism for setting up channel
parameters since that will just result in duplicated code. IBSS, mesh,
and AP mode can use the same data structures and parameters for setting
up such parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Jouni Malinen
54fe48b9dc mesh: Use the shared function with IBSS to determine channel parameters
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Jouni Malinen
f7e889fa2d mesh: Convert channel configuration to use common routines
Use struct hostapd_freq_params just like other modes do instead of
mesh-specific freq and ht_mode.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Jouni Malinen
6334330ed6 mesh: Use a separate variable to track whether HT is enabled
A network profile parameter should not be used to check whether the
currently operating mesh has HT enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Janusz Dziedzic
6b8b07741a ibss/mesh: Enable HT40 if supported
Setup HT40+/HT40- if supported by driver.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-01-10 17:35:53 +02:00
Janusz Dziedzic
269dfe232b Introduce common hw features
Introduce wpa_supplicant/hostapd hw features.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-01-10 17:35:53 +02:00
Janusz Dziedzic
1830817ece IBSS: Add WPA_DRIVER_FLAGS_HT_IBSS
Add WPA_DRIVER_FLAGS_HT_IBSS driver feature flag. Some drivers could not
set this feature and next could fail when we will enable HT support for
IBSS with error message: nl80211: Join IBSS failed: ret=-22 (Invalid
argument).

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-01-10 17:35:53 +02:00
Bob Copeland
a206e2a175 SAE: Centralize function for sending initial COMMIT
When performing SAE authentication in mesh, one station may
initiate authentication by sending a COMMIT as soon as a peer
candidate is discovered. Previously we did this in mesh_rsn.c,
but this left some of the state initialization in a different
part of the code from the rest of the state machine, and we may
need to add other initializations here in the future, so move
that to a more central function.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
2015-01-10 11:43:29 +02:00
Jouni Malinen
a354bcc886 D-Bus: Use NoMemory error message from CreateInterface
Try to be a bit more consistent by using NoMemory instead of InvalidArgs
if os_strdup() fails in the CreateInterface handler.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-09 02:32:15 +02:00
Jouni Malinen
635874b55a Handle interface disabled/enabled more consistently
It was possible for the interface not to be marked in INTERFACE_DISABLED
state in case the event was processed for P2P GO because the wpa_s
instance could have been removed in case of a separate group interface.
Change the state first to avoid leaving different state for the case
where separate group interface is not used.

Mark scan to be a normal scan on INTERFACE_ENABLED so that scanning
rules (e.g., skip scan if no networks enabled) get used consistently.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Jouni Malinen
8f2cf37923 P2P: Indicate reason=UNAVAILABLE for group netdev going down
There is a race condition between receiving an AP stopped event and
netdev down event. These resulted in different group removal reasons on
a GO device (UNAVAILABLE for stop AP event coming first and REQUESTED
for netdev event first). Make this more consistent by reporting
UNAVAILABLE for both possible cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Jouni Malinen
a156ffda61 Add support for testing memory allocation failures
The new control interface command TEST_ALLOC_FAIL and GET_ALLOC_FAIL can
now be used to trigger memory allocation failures for testing purposes.
TEST_ALLOC_FAIL sets a failure conditions with
<count>:func[;func][;func]... string and GET_ALLOC_FAIL returns the
current state using the same format. Whenever an allocation is made with
a matching backtrace of calling functions, the count is decremented by
one and once zero is reached, the allocation is forced to fail.

Function names can be prefixed with either '=' or '?' to get different
matching behavior. '=' requires this specific function to be the next
one in the backtrace (i.e., do not skip any other functions in the list
which is the default behavior). '?' allows the function to be optionally
present in the backtrace.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:43 +02:00
Jouni Malinen
52b3943c94 D-Bus: Fix interface unregistration on error path
It is possible for this function to get called even if D-Bus
registration had failed, so the path can be NULL here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:01 +02:00
Jouni Malinen
96dc9a6d42 D-Bus (old): Fix interface unregistration on error path
It is possible for this function to be called even if D-Bus interface
registration has failed. Avoid a D-Bus assert in such a case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:01 +02:00
Jouni Malinen
ef0355780a Fix memory leak on wpa_supplicant_init_wpa() error path
If wpa_sm_init() fails, the context data needs to be freed in the
caller.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
f2d57282ad D-Bus: Fix string array dict entry parser in out-of-memory case
entry->strarray_value was left to point to freed memory in case
os_realloc_array() failed. This resulted in the following
wpa_dbus_dict_entry_clear() trying to free an already freed memory area.
In addition, the separately allocated strings in the array would have
been leaked in such a case. Furthermore, wpa_dbus_dict_entry_clear() was
not prepared for the possibility of the initial os_calloc() call failing
and entry->strarray_value being NULL without array_len being cleared to
zero. That would have resulted in reading uninitialized memory and NULL
pointer dereference.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
c61bc23aa2 D-Bus: Fix byte array dict entry parser in out-of-memory case
entry->bytearray_value was left to point to freed memory in case
os_realloc_array() failed. This resulted in the following
wpa_dbus_dict_entry_clear() trying to free an already freed memory area.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
dacf605812 D-Bus: Fix Introspect() in case of os_strdup() failure
add_interface() did not check for os_strdup() return value and could end
up dereferencing a NULL pointer if memory allocation failed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
68a866974b D-Bus (old): Fix wpsReg error message
This was supposed to return WpsRegError, not WpsPbcError.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
f0614bc6c6 D-Bus (old): Fix message handler error paths
The error reply needs to be sent out as a response. The "out" label was
in incorrect place to allow that to happen; instead, it ended up leaking
memory for the generated reply message.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
a2af1c70c5 D-Bus (old): Fix memory leak on error path
If setSmartcardModules() fails to allocate memory with os_strdup(), the
allocated items in the dict entry were not freed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:00 +02:00
Jouni Malinen
942b75468d tests: Add module tests for AES-SIV
This moves the AES-SIV test case from tests/test-aes.c to be part of
wpa_supplicant module testing framework with a new
src/crypto/crypto_module_tests.c component. In addition, the second test
vector from RFC 5297 is also included for additional coverage.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-05 15:50:53 +02:00
Ilan Peer
8b48e32006 wpa_cli: Add MAC address randomization in scan
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Ilan Peer
fb375883f4 ctrl_iface: Add MAC address randomization in scan processing
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Ilan Peer
56c76fa592 scan: Add MAC address randomization in scan handling
1. Supported MAC address randomization for scan.
2. Supported MAC address randomization for scheduled scan.
2. Supported MAC address randomization for pno.
4. Add functions to set and clear the MAC address randomization
   state variables.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Arik Nemtsov
7db53bb8c5 wpa_cli: Implement TDLS start/cancel channel switching commands
For the start operation, this includes appropriate parameters for
specifying channel and peer information. The cancel operation includes
peer information.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 21:46:37 +02:00
Arik Nemtsov
6b90deae4d TDLS: Propagate enable/disable channel-switch commands to driver
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.

Allow enable/disable operations to be invoked via the control interface.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 20:30:11 +02:00
Arik Nemtsov
4daa572925 TDLS: Add channel-switch capability flag
Propagate a driver TDLS channel-switch support bit from nl80211 to
TDLS code.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 18:59:31 +02:00