This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
Netlink sockets can be shared among all driver instances, saving lots
of sockets, spurious log messages, memory, and CPU usage when using
multiple interfaces in a single process.
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Some dualband cards can use more than five seconds to run through
a full scan, so increase the timeout to avoid hitting the missing
scan completed event workaround.
This fixes an issue where WPS run leaves a small ClientTimeout
value (2) configured and the next EAPOL authentication is started
with that small value even for Identity exchange. This can cause
problems when an EAPOL packet gets dropped immediately after
association and a retry of that packet is needed (which may take
more than two seconds).
This function can be used to clean up local UNIX domain socket files
that may be left over from clients that were previously connected to
wpa_supplicant. At least for now, this is only available for Android
builds.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
AP mode operations were used for P2P device discovery Listen state
only during early experiments. This has now been cleaned up and
ieee802_11_set_beacon() is not called for P2P device discovery.
As such, this hack to skip Beacon configuration can be removed.
This is the first step in allowing SA Query mechanism in hostapd to be
used with drivers that implement authentication and association MLME/SME
(i.e., do not use ieee802_11.c).
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
Commit 17f6b90056 moved the concatenation
of WPS IEs, but did not include the validation that the IE buffer is not
NULL. In addition, the concatenation needs to be done based on the full
IE buffer instead of the parsed pointer that includes only a single
WPS IE.
The base64 encoded data cannot included pad characters in the middle, so
we can stop the loop at the first sequence of pad characters. If the
sequence includes more than two pad characters, the encoding is invalid
and we can indicate failure.
Use the SSID filter list passed in the scheduled scan request down to
the kernel driver, so it can use the list to return only the wanted
SSIDs. Some kernel drivers can use this information to offload the
SSID filter to the hardware, helping with reducing the power
consumption.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.
Signed-off-by: Luciano Coelho <coelho@ti.com>
With scheduled scan support, we may need to pass more than 10 SSIDs in
a single scan request. Some drivers (e.g., wl12xx) support up to 16
SSIDs at once.
Change WPAS_MAX_SCAN_SSIDS from 10 to 16.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 19ec1f262e tried to fix some
cases for history prev selection, but it broke others. Fix this
properly by using a separate entry for the current edit line that
is not yet in history buffer.
Currently the P2P Interface name[p2p-%s-%d] is reset when the P2P
Interface name reaches the "IFNAMSIZ" limit. Monitor interface name is
derived from p2p interface name with the addition of few characters
[mon.p2p-%s-%d] and hence Monitor interface name hits IFNAMSIZ limit
before P2P Interface name. Rename the monitor interface name to
mon-%s-%d to reduce the length to same with p2p-%s-%d.
Data path for stations that get successfully associated to the
hostapd but fail to get added in the driver/firmware, will not
work. In such cases, hostapd should deauth and disconnect such
stations. In such scenario, hostapd should disconnect the STAs.
Sample output with following patch
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: authenticated
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: associated (aid 1)
wlan0: AP-STA-CONNECTED 0c:74:c2:9a:4c:59
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: Could not add STA to kernel driver
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: deauthenticated due to local deauth request
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The password_hash parameter was not copied in case of the integrated
authentication server (but was for RADIUS server). This broke EAP
authentication when the user entry used NT-hash.
This currently unused function would have triggered wpabuf overflows
due to incorrect variable being reset to zero in the case the old
NoA wpabuf was large enough for the new data.
The EAPOL authenticator was previously forcing disconnection in the WPS
use case. However, this can be benefitial operation with any IEEE 802.1X
authentication mechanism and need not be limited to WPS. This helps some
use cases like EAP-FAST where provisioning may require two
authentication runs if the authentication server does not allow the PAC
provisioning step to be used for normal data connection. While the
station would be free to decide to re-associate in such a case, not all
stations do and as such, it helps if the AP does that instead of leaving
the association up with EAPOL state machine in HELD state for 60
seconds.
While EAP-FAST uses protected success notification, RFC 5422, Section
3.5 points out a possibility of EAP-Failure being sent out even after
protected success notification in case of provisioning. Change the
EAP-FAST peer implementation to accept that exception to the protected
success notification. This allows the station to re-connect more quickly
to complete EAP-FAST connection in the case the server rejects the
initial attempt by only allowing it to use to provision a new PAC.
If GO Negotiation Request (or in theory, also GO Negotiation Response)
frame is delivered multiple time for processing, the SSID of the group
could end up getting changed. This could result in possible issues if
the peer ended up using different SSID. To avoid this, make sure the
SSID does not get changed unless the negotiation is for a new group.
Whenever PMK gets changed (e.g., due to re-authentication), all PMKSA
caching entries that were created using the previous PMK needs to be
replaced. Previously, only the entry for the current AP was cleared.
Flush the other entries based on network_ctx matches to get rid of the
OKC entries. These entries can then be re-creating using OKC with the
new PMK.
When polling a station that has been inactive for a while, hostapd currently
always uses a null data frame. This is a bit strange with uAPSD clients
(though it seems to mostly work) since the EOSP bit can never be set in a
non-QoS frame. Make hostapd use QoS null data frames for probing when the
station is a QoS STA.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wrap self-generated WPS credential for new AP settings and send that to
control interface to provide the needed information in
WPS-NEW-AP-SETTINGS for external processing.
GAS/ANQP is a generic protocol and in no way specific to P2P, so move
routines used to build GAS/ANQP frames to a separate file that can be
shared for other uses than just P2P service discovery.
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.
Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
If the initial attempt to start a scan for p2p_find fails, an error
is reported. However, the P2P scan handler and search state was
left behind. That can result in unexpected behavior when the next
non-P2P scan results are indicated. Avoid this by clearing the
P2P search state on failure.
This new flag can be used to change wpa_supplicant behavior in the
default ap_scan=1 mode to move BSS selection into the driver (likely
firmware). This commit is only adding the flag; separate commits
will be used to change the actual connection/roaming behavior.
These protocols seem to be abandoned: latest IETF drafts have expired
years ago and it does not seem likely that EAP-TTLSv1 would be
deployed. The implementation in hostapd/wpa_supplicant was not complete
and not fully tested. In addition, the TLS/IA functionality was only
available when GnuTLS was used. Since GnuTLS removed this functionality
in 3.0.0, there is no available TLS/IA implementation in the latest
version of any supported TLS library.
Remove the EAP-TTLSv1 and TLS/IA implementation to clean up unwanted
complexity from hostapd and wpa_supplicant. In addition, this removes
any potential use of the GnuTLS extra library.
This fixes some build issues in GnuTLS wrapper to be compatible with
at least following GnuTLS versions: 2.2.5, 2.4.3, 2.6.6, 2.8.6,
2.10.5, 2.12.11, 3.0.3.
Instead of using separate bad_record_mac and decryption_failed alerts,
use only bad_record_mac alert regardless of how the CBC decryption
failed. This provides less information to attackers that could modify
packets. In addition, instead of returning immediately on error, run
through the MAC check to make timing attacks more difficult.
When the received data will be decrypted, there is no need to first
copy it and then handle decryption in-place when decryption step can
take care of both operations.
TLS v1.0 and v1.1 RFCs were not exactly clear on the use of the
protocol version in record later. As such, accept any {03,xx} value
to remain compatible with existing implementations and new protocol
versions.
The p2p->drv_in_listen variable is used to track Listen state operations
in the driver. This is cleared when the driver reports that the Listen
state has ended (p2p_listen_end() gets called). However, it is possible
that the driver does not indicate that if the Listen state is canceled.
This can apparently happen in some cases where p2p_connect command is
issues while the Listen state is in progress.
Work around this issue by clearing p2p->drv_in_listen when Listen state
is stopped as part of p2p_stop operation. This allows the P2P module to
process CONNECT_LISTEN timeout in p2p_timeout_connect_listen() to move
to CONNECT state, e.g., when starting GO Negotiation after Device
Discoverability mechanism.
The "too long" buffer (32+1 octets) prevented AP from starting up with
32 octet SSID with WE-21 and newer. Fix this by reducing the
SIOCGIWESSID buffer length.
This adds support for RSN pre-authentication with nl80211 interface and
drivers that handle roaming internally (i.e., wpa_supplicant is not
responsible for requesting scan results that provide the needed
information without these events).
cfg80211 does not currently allow NL80211_CMD_CONNECT when there
is already an association. This can result in wpa_supplicant being
unable to request a connection if the interface is already in
connected state. Work around this by requesting disconnection if
the connect command fails with EALREADY error. This allows
wpa_supplicant to recover from the unexpected state and complete
the connect request on next attempt.
eapol_test command line argument -o<file> can now be used to request
the received server certificate chain to be written to the specified
file. The certificates will be written in PEM format. [Bug 391]
Make the WPS processing of (Re)Association Request frame IEs conditional
on WPS support. This fixes a build issue with wps_is_20() not being
defined and makes the non-WPS build a bit smaller.
os_*() wrappers should be used instead of functions from time.h.
Removing the header from includes.h enforces this. os_unix.c can
include this its uses are valid wrapper calls. wps_upnp.c uses
gmtime() for which there is no os_*() wrapper available yet, so
allow it to use time.h, too. Similarly, allow dump_state.c to
use time.h for ctime().
Currently, the following can happen:
1) P2P state machine requests R-O-C
2) user changes their mind and aborts
3) P2P state machine aborts R-O-C
4) driver_nl80211 rejects abort since there
was no notification about the start yet
5) R-O-C period start notification from kernel
6) P2P state machine requests new R-O-C
7) this overlaps with old R-O-C -- iwlwifi driver
can't handle that and returns -EBUSY
8) state machine stops dead in its tracks
The reason is that the abort isn't going through properly. Instead of
tracking whether a R-O-C is active in driver_nl80211, track whether one
was requested to avoid this scenario.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Since the kernel can now advertise P2P concurrent support by advertising
interface combinations, we can take advantage of that and automatically
use P2P_CONCURRENT / P2P_MGMT_AND_NON_P2P for drivers that advertise
support.
Keep driver_param=use_p2p_group_interface=1 for anyone not advertising
interface combinations in their drivers yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The default config methods was hardcoded to claim support for
PushButton, Display, and Keypad. While these are supported by
most P2P devices, there may be some cases where it is convenient
to be able to disable a specific config method. Use config_methods
configuration parameter to set the default values for Config Methods
in the P2P Device Info attribute.
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
If a network configuration block is removed or modified, flush
all PMKSA cache entries that were created using that network
configuration. Similarly, invalidate EAP state (fast re-auth).
The special case for OKC on wpa_supplicant reconfiguration
(network_ctx pointer change) is now addressed as part of the
PMKSA cache flushing, so it does not need a separate mechanism
for clearing the network_ctx values in the PMKSA cache.
If the driver maintains its own copy of the PMKSA cache, we need to
clear an entry from the driver whenever wpa_supplicant is dropping
an old PMKSA cache entry.
The Deauth/Disassoc TX status callbacks were ending up kicking the
station entry from kernel driver when test functionality was used to
inject Deauth/Disassoc frames from the AP with the purpose of leaving
the local association in place. Fix this by using STA flags to figure
out whether there was a pending callback for the frame that we need
to act on.
In addition, add forgotten functionality for the Disassoc TX status
callback to match the behavior with Deauth.
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
Instead of hardcoding the Config Methods attribute value in Probe
Request frames, set this based on the configured parameter
config_methods to allow correct set of methods to be advertised.
The device description file may include multiple devices. Improve the
simplistic parser by first trying to find the WFADevice:1 device before
fetching the device parameters. While this is still far from complete
XML parsing, this should address the most common root device
specifications.
This allows non-mac80211 drivers to report received Probe Request
frames to user space and Probe Response and Action frames to be sent
from user space when using AP/P2P GO mode.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. The STA
entry (and PTK) will be removed from the kernel only after the
Deauth/Disassoc has been transmitted (e.g., when the STA wakes up).
A hardcoded two second timeout is used to limit the length of this
window should the driver fail to deliver the frame (e.g., the STA
is out of range and does not wake up). The kernel STA entry is
marked unauthorized during the wait to avoid accepting Data
frames from the STA that we have decided to disconnect.
This behavior is available only with drivers that provide TX status
events for Deauth/Disassoc frames (nl80211 at this point). Other
drivers continue to use the previous behavior where the STA entry
is removed immediately.
Extend the code that waits for the station to send EAPOL-Start before
initiating EAPOL authenticator operations to cover the case where the
station includes WPS IE in (Re)Association Request frame if that IE
does not include support for WPS 2.0. While this should not really
be needed, this may help with some deployed WPS 1.0 stations that do
not support EAPOL operations correctly and may get confused of the
EAP-Request/Identity packets that would show up twice if EAPOL-Start
is transmitted.
If an ER tries to send a message to a STA that is not in the middle
of WPS protocol, do not try to deliver that. This can help with issues
where an ER takes long time to reply to M1 and another Registrar has
already completed negotiation.
It is possible to get a response for a pending EAP callback after the
EAP state machine has already completed its work or has timed out. For
those cases, make sure that the callback function is not delivered since
it could result in NULL pointer dereferences.
The Config Methods attribute in M2 and M2D messages is supposed to
indicate which configuration methods are supported by the Registrar. As
such, it should not depend on whether PBC mode is currently active or
not. That will only affect the Selected Registrar Config Methods and
Device Password ID attributes.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Split WPA initialization into two parts so that the Beacon frames can be
configured fully before the initial keys (GTK/IGTK) are configured. This
makes it easier for drivers that depend on the AP security mode being
fully set before the keys are configured.
This avoids a request to the driver to first start beaconing before
the WPA/RSN IE has been generated and then immediately changing the
beacon IEs once the WPA/RSN IE is ready.
Such using params->wpa_ie to figure out whether the connection is for
WPA/WPA2 is not correct since that buffer is used also to add WPS IE. In
case of WPS, do not add NL80211_ATTR_WPA_VERSIONS to avoid confusing
drivers.
Some compilers complain about fwrite calls if the return value is
not checked, so check the value even if it does not really make
much of a difference in this particular case.
The internal TLS implementation assumes that the certificate chain
is ordered by issuer certificate following the certificate that it
signed. Add the certificates to the chain in suitable order when
loading multiple certificates.
Commit e1d526293b added code for verifying
whether the receive Probe Request frame was indicating support for only
802.11b rates, but it missed the for loop for the extended supported
rates element. Add that to fix the validation code for cases where
non-802.11b rates are in the extended supported rates element.
