Add an attribute QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2
for describing the secondary 80 MHz span of agile spectral scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL in enum
qca_wlan_vendor_cfr_capture_type. This capture type requests all NDPA
NDP frames to be filtered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhanced channel frequency response supports capturing of channel status
information based on RX. Define previous CFR as version 1 and enhanced
CFR as version 2. If target supports both versions, two versions can't
be enabled at same time. Extend attributes for enhanced CFR capture in
enum qca_wlan_vendor_peer_cfr_capture_attr.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add more hang reason codes for the hang reason in the
QCA_NL80211_VENDOR_SUBCMD_HANG events. This also introduces the
attribute QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA to carry the required
data for the respective hang reason. This data is expected to contain
the required dump to analyze the reason for the hang.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME for specifying
dwell time in the QCA vendor scan command. This is a common value which
applies across all frequencies requested in the scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute enables/disables the host driver to send roam reason
information in the Reassociation Request frame to the AP in the same
ESS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of the attributes were defined with inconsistent prefix in the
name (missing "CONFIG_"). Fix these to use the common prefix for all
enum qca_wlan_vendor_attr_config values. Add defined values for the
incorrect names to avoid issues with existing users.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit adds new attributes for getting the Probe Response frame
IEs, Beacon frame IEs and the disconnection reason codes through
get_sta_info vendor command.
The host driver shall give this driver specific reason code through
the disconnection reason code attribute
QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute aims to configure the STA to send the Beacon Report
Response with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As qca_vendor.h alone can be included by other applications, define
macro BIT() in qca_vendor.h itself if not yet defined, e.g., by
including utils/common.h before qca_vendor.h.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces additional stats to query through
QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY for
primary channel center frequency in the definition for Representative
Tx Power List (RTPL) list entry instance. This is required for 6 GHz
support, since the 6 GHz channel numbers overlap with existing 2.4 GHz
and 5 GHz channel numbers thus requiring frequency values to uniquely
identify channels.
Mark QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY as deprecated if both the
driver and user space application support 6 GHz. For backward
compatibility, QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if
either the driver or user space application or both do not support the
6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces the vendor event
QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT.
Host drivers can request user space application to set SAR power
limits with this event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to set thermal level to the driver from
userspace. The driver/firmware takes actions requested by userspace to
mitigate high temperature such as throttling TX etc. The driver may
choose the level of throttling and other actions for various thermal
levels set by userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the documentation with values to be sent for seg0 and seg1 fields
in external ACS result event for 20 MHz, 40 MHz, 80 MHz, 160 MHz, and
80+80 MHz channels. These values match the changes done to definitions
of seg0 and seg1 fields in the IEEE 802.11 standard.
This vendor command had not previously been documented in this level of
detail and had not actually been used for the only case that could have
two different interpretation (160 MHz) based on which version of IEEE
802.11 standard is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO with
attributes defined in enum qca_wlan_vendor_attr_get_sta to get
information for a BSS in STA mode or for a peer STA in AP mode. This
vendor sub command can be used to get STA information from the driver to
userspace. The attributes defined in enum
qca_wlan_vendor_attr_get_sta_info are used to encapsulate required
information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
To config BT coex chain mode, add a new QCA sub command
QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE.
This new command has two attributes:
1. QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute. Indicates the
BT coex chain mode, are 32-bit values from enum qca_btc_chain_mode.
2. QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute.
If set, vdev should be restarted once BT coex chain mode is updated.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
The QCA_NL80211_VENDOR_SUBCMD_OEM_DATA command was previously defined
only to pass data blobs from user space to kernel (application to
firmware) but there was no mechanism to send the data blobs from
firmware to application. Extend this to define use of the same
subcommand and attributes as vendor events.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE with
attributes qca_wlan_vendor_attr_add_sta_node_params to add STA peer
entries in AP mode. This vendor sub command is used in FT roaming
scenario to send STA node information from application/service to
driver/firmware. The attributes defined in enum
qca_wlan_vendor_attr_add_sta_node_params are used to deliver the
parameters.
Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
The OEM data binary blobs from application/service will be routed to the
appropriate device based on this attribute value. This optional
attribute is used to specify whether the device type is virtual or
physical. This attribute can be omitted when the command is for a
virtual device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some chipsets don't have the capability to run agile spectral scan with
160/80+80 MHz modes. Add separate agile spectral scanning capability
flags for 160, 80+80, and non-160 MHz modes to cover such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the documentation of QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST
to make it a nested attribute to carry frequencies of type u32.
This is to be in sync with the nl80211 attribute
NL80211_ATTR_SCAN_FREQUENCIES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT
and attribute qca_wlan_vendor_attr_avoid_frequency_ext to send structured
avoid frequency data.
This new command is alternative to existing command
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command is
using stream of bytes instead of structured data using vendor attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
As a part of P802.11ax amendment, 6 GHz band operation is added.
Since the 6 GHz channel numbers are overlapping with existing 2.4 GHz
and 5 GHz channel numbers, use frequency to identify unique channel
operation instead of channel number. Channel frequency is unique across
bands.
In the existing QCA vendor interface, wherever missing, add frequency
attributes to identify unique channel operation. In addition, add
comments to document some of the previously missed attributes/values.
Note: If both channel and frequency attributes are present in vendor
command/event and
(a) If both the driver and user-space application supports 6 GHz band
then channel related attributes are deprecated and use frequency
attributes.
(b) If either driver or user-space application or both doesn't
support 6 GHz band then use channel attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL attribute in
enum qca_wlan_vendor_attr_sap_config to use with vendor command
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG.
This new attribute is used to restart AP on given channel.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY
with attributes enum qca_wlan_vendor_attr_acs_config and
enum qca_acs_dfs_mode to configure ACS policy.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
This enhances the existing vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM
with the following configurations:
1. Set/get/clear roam control
2. Set/get the channels on which the roaming has to be triggered.
3. Set/get the roam scan period.
4. Configure the triggers for roaming.
5. Configure the candidate selection criteria.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
qca_wlan_vendor_attr_roam_subcmd is an enum associated with the
attribute QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. It represents different
sub command values and these are not the attributes. Hence, rename the
enum to qca_wlan_vendor_roaming_subcmd. Accordingly, the members of this
enum are also renamed to suite the usage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add attributes QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS under
the enum qca_wlan_vendor_attr_config to support set and get
the ELNA bypass.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES
to configure disconnect IEs to the driver. Driver shall fill
these IEs in disassoc/deauth frame.
These IEs are expected to be considered only for the next
immediate disconnection (disassoc/deauth frame) originated by
the DUT, irrespective of the entity (user space/driver/firmware)
triggering the disconnection.
The host drivers are not expected to use the IEs set through
this interface for further disconnections after the first immediate
disconnection initiated post the configuration.
If the IEs are also updated through cfg80211 interface (after the
enhancement to cfg80211_disconnect), host driver is expected to
take the union of IEs from both of these interfaces and send in
further disassoc/deauth frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
with attributes qca_wlan_vendor_attr_oem_data_params to support
OEM data. It is used to send OEM data binary blobs from
application/service to firmware. The attributes defined in enum
qca_wlan_vendor_attr_oem_data_params are used to deliver the
parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
The driver automatically starts beacon reporting if it pauses the beacon
reporting for any reason other than disconnection. In specific cases,
userspace may not want the beacon reporting to be automatically resumed
after a pause. Add interface support for userspace to specify driver not
to start beacon reporting automatically after a pause.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attributes under the enum
qca_wlan_vendor_attr_spectral_scan to support the configuration of
Spectral DMA debug.
1. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG
Enable/disable debug of the Spectral DMA ring
2. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG
Enable/disable debug of the Spectral DMA buffers
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In practice, some APs have interop issues with the DUT. This sub command
is used to transfer the AP info between the driver and user space. This
works both as a command and event. As a command, it configures the
stored list of APs from user space to firmware; as an event, it
indicates the AP info detected by the firmware to user space for
persistent storage. The attributes defined in enum
qca_vendor_attr_interop_issues_ap are used to deliver the parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
Update enum qca_wlan_vendor_attr_get_wifi_info to add support for
attribute QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX. In addition
update the documentation for qca_wlan_vendor_attr_get_wifi_info and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO to fully describe the
operation of the command and the format of the attributes.
Signed-off-by: Jeff Johnson <jjohnson@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING
to implement beacon reporting feature. Different operations required to
implement this feature can be specified in
QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE.
Userspace requests the driver/firmware to periodically report received
Beacon frames whose BSSID matches the current connected BSS's MAC
address. If userspace requests the driver/firmware to send beacon
reports actively, the driver encapsulates the details of the beacon in
an event and sends it to userspace asynchronously. Otherwise, the driver
will only update the beacon in cfg80211 scan cache but will not send any
event to userspace.
If this command is not issued, the current behavior of the
driver/firmware is to update the cfg80211 scan cache only when there is
a scan issued by the host in progress or whenever there is a change in
IEs of the Beacon frames from the current connected BSS.
The userspace requests the driver/firmware to stop reporting beacons
when reporting is not required anymore. If the driver/firmware is not
able to receive Beacon frames because of other Wi-Fi operations such as
off-channel activities, etc., the driver/firmware sends a pause event to
userspace and stops reporting Beacon frames. The driver/firmware
indicates whether the beacon reporting automatically resumes later by
using the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES flag. If
userspace doesn't want the beacon reporting to be resumed automatically,
userspace can send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP command to
the driver to stop beacon reporting.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces an attribute
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON to carry the roam reason code
through QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This subcommand is used to update Zigbee state and specified WLAN
durations to enhance success ratio of Zigbee joining network. The
attributes defined in enum qca_mpta_helper_vendor_attr are used to
deliver these parameters to the driver.
Signed-off-by: stonez <stonez@codeaurora.org>
Peer rate statistics is per-peer cached data in the driver. These
statistics needs to be flushed to a user space application on
synchronous/asynchronous events. This command is used as an event from
the driver to flush per-peer cached statistics to the application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor specific feature capability indication for the
device to indicate the support of TWT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current/default behavior of set blacklist BSSID QCA vendor command
is a mandate to the driver - do not consider this BSSID for connect/roam
till reset.
There are use cases where this need not be a mandate and thus could
provide the flexibility for the driver to consider this BSSID if there
are no better ones. Such use cases can use this new flag attribute to
only hint the blacklist of a BSSID to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
