CONFIG_DPP3=y can now be used to configure hostapd and wpa_supplicant
builds to include DPP version 3 functionality. This functionality is
still under design and the implementation is experimental and not
suitable to be enabled in production uses before the specification has
been finalized.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Align the process logic for ap_vendor_elements and ap_assocresp_elements
parsing by using the wpabuf_parse_bin() helper function in both.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
wpa_add_scan_freqs_list() was updated to use bool for the is_6ghz
argument, but these callers were missed when updating the values from
0/1 to false/true.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channels included for the scan to connect to a P2P GO are optimized
such that the P2P GO preferred channel and the common channels are
included for the first few scans followed by a full scan in which all
the channels supported by the local device are included. This results in
P2P client including the 6 GHz channels for the full scan after GO
Negotiation even when 6 GHz channels are not used for the P2P
connection.
Exclude the 6 GHz channels from the full scan if 6 GHz channels are
supported but are not used for P2P connection.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
update proto type, AKMP suite, and pairwise cipher suite based on the
(Re)Association Request frame. Update PMF, group cipher, and group mgmt
cipher based on the AP's RSNE into wpa_sm. group_mgmt_cipher needs to be
updated based on PMF capabilities of STA and roamed AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since the 6 GHz band has no DFS channels, enable 6 GHz 160 MHz bandwidth
as the default configuration for IEEE 802.11s mesh.
example:
network={
ssid="6gmesh160"
key_mgmt=SAE
mode=5
frequency=6275
psk="1234567890"
}
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
IEEE Std 802.11ax-2021 mandates 6 GHz STA to use Management Frame
Protection (MFP) when RSN is enabled.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Channel numbers of the 6 GHz band overlap those of the 2.4 GHz and 5 GHz
bands. Thus converting to frequency based mesh channel selection helps
accommodate 6 GHz mesh.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
AKMP and proto were not updated in wpa_sm. Hence, update AKMP and proto
used with roamed AP when association event received from the driver in
SME offloaded to the driver scenario to avoid incorrect AKMP details in
wpa_supplicant similarly to how the cipher suite updates were added in
commit 2b3e64a0fb ("Update ciphers to address GTK renewal failures
while roaming") .
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Wi-Fi Display functionality needs P2P to be enabled. Ignore
CONFIG_WIFI_DISPLAY if CONFIG_P2P is not enabled for the build. This
avoids following compilation issue with invalid build configuration:
../src/ap/ap_drv_ops.c: In function 'hostapd_build_ap_extra_ies':
../src/ap/ap_drv_ops.c:163:10: error: 'struct hostapd_data' has no member named 'p2p_group'
163 | if (hapd->p2p_group) {
| ^~
../src/ap/ap_drv_ops.c:165:35: error: 'struct hostapd_data' has no member named 'p2p_group'
165 | a = p2p_group_assoc_resp_ie(hapd->p2p_group, P2P_SC_SUCCESS);
| ^~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit b0f457b619 ("SAE: Do not expire the current PMKSA cache entry")
depends on sm->cur_pmksa to determine if it is the current PMKSA cache
entry, but sm->cur_pmksa was not always correct for SAE in the current
implementation.
Set sm->cur_pmksa in wpa_sm_set_pmk() (which is used with SAE), and skip
clearing of sm->cur_pmksa for SAE in wpa_find_assoc_pmkid(). This latter
case was added by commit c2080e8657 ("Clear current PMKSA cache
selection on association/roam") for driver-based roaming indication and
Suite B, so skipping it for SAE should be fine.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using pkg-config for libpcsclite can provide more accurate linking
flags.
Signed-off-by: Reinhard Tartler <siretart@tauware.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Make sure that D-Bus isn't shut down before wpa_supplicant, as that would
also bring down wireless links which are still holding open NFS shares.
Debian bug: https://bugs.debian.org/785579
systemd upstream bug: https://bugs.freedesktop.org/show_bug.cgi?id=89847
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Every usage of these variables appends an extra slash, so keeping
a slash in the default values leads to double slashes in resulting
paths.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Some distros carry patches to specify driver fallback, but only in
specific conditions (e.g. the systemd service definition[1]). This leaves
other wpa_supplicant instances needing to define fallback themselves,
which leads to places where wpa_supplicant thinks it can't find a
driver[2]. Instead, when -D is not specified, have wpa_supplicant try
all the drivers it was built with in an attempt to find a working one
instead of just giving up if the first doesn't work.
[1] https://salsa.debian.org/debian/wpa/-/blob/debian/unstable/debian/patches/networkd-driver-fallback.patch
[2] https://bugs.launchpad.net/netplan/+bug/1814012
Signed-off-by: Kees Cook <kees@ubuntu.com>
Update PMKSA cache when interface is disabled and then enabled based on
the new MAC address. If the new MAC address is same as the previous MAC
address, the PMKSA cache entries are valid and hence update the PMKSA
cache entries to the driver. If the new MAC address is not same as the
previous MAC address, the PMKSA cache entries will not be valid anymore
and hence delete the PMKSA cache entries.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
While creating a cloned PMKSA entry for OKC both expiration and
reauth_time values are set to maximum values, but later only the
expiration time is copied from the old PMKSA entry to the new PMKSA
entry. Due to this there is a possibility of reauth_time becoming
greater than expiration time in some cloned entries. To avoid this copy
reauth_time also to the cloned entry.
Also, add check to reject control interface commands with reauth time
greater than expiration time.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Replaced the word "sanity" with the inclusive word "validity". The
comment in acs_survey_interference_factor() was referring a function
that does not exist, so remove it instead of trying rename the function.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Allow sae_pwe parameter to be configured per-network and enforce the
SAE hash-to-element mechanism for the P2P GO if it is started on
a 6 GHz channel.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming from WPA2-AP (group=CCMP) to WPA-AP (group=TKIP) using
driver-based SME and roaming trigger, GTK renewal failures are observed
for the currently associated WPA-AP because of group cipher mismatch,
resulting in deauthentication with the AP.
Update the group cipher and pairwise cipher values in wpa_sm from
association event received from the driver in case of SME offload to the
driver to address GTK renewal failures (and similar issues) that could
happen when the driver/firmware roams between APs with different
security profiles.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an explicit check for modes != NULL instead of depending on
num_modes > 0 implying that. This is to silence invalid static analyzer
reports.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support adding/deleting vendor elements dynamically for AP mode while it
is started by wpa_supplicant instead of hostapd which already supported
this. This adds ap_assocresp_elements global parameter and UPDATE_BEACON
control interface command to take the changed values into effect.
Usage in wpa_cli:
Add vendor IE for (Re)Association Response frames
> set ap_assocresp_elements=xxxx
Add vendor IE for Beacon/Probe Response frames
> set ap_vendor_elements=xxxx
Delete vendor IE from (Re)Association Response frames
> set ap_assocresp_elements
Delete vendor IE from Beacon/Probe Response frames
> set ap_vendor_elements
To make vendor IE changes take effect
> update_beacon
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Add support to send DSCP Policy Query frame using a new control
interface command DSCP_QUERY. This includes support for a wildcard DSCP
query and a DSCP query with a single Domain Name attribute.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse WFA Capabilities element from the (Re)Association
Response frame. Also register a timeout for the station to wait before
sending a new DSCP query if requested by AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Indicate DSCP Policy capability by including a WFA Capabilities element
containing the relevant bit set to 1 in the (Re)Association Request
frames when enabled by user.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to prepare and send DSCP response action frame to the
connected AP in response to a new control interface command DSCP_RESP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse received DSCP Policy Request frames and send the
request details as control interface events.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The DSCP policy capability is disabled by default. The user frameworks
which have support for handling DSCP policy request messages need to
enable this capability explicitly to allow wpa_supplicant to advertise
the capability to the AP and allow the related frames to be processed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This function is not specific to GAS, so make it available throughout
wpa_supplicant without requiring CONFIG_GAS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.
For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'
- Previous behavior: AP fallback to channel 100 using 20 MHz with
"No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
"VHT center channel 106 for 80 or 80+80 MHz bandwidth"
This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enable support for P2P connection in 6 GHz with the channel width of 40
MHz, 80 MHz, and 160 MHz. The flag max_oper_chwidth is used to configure
the maximum channel width for P2P connection in 6 GHz with the commands
P2P_CONNECT, P2P_INVITE, and P2P_GROUP_ADD.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Current definition of wpas_p2p_get_ht40_mode() determines secondary
offset in the 5 GHz band. Enhance the functionality of this function to
determine offset to support 6 GHz channels also.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Clone pmf and p2p_6ghz_disable configuration values when creating a new
P2P group interface. PMF is required in 6 GHz band operation.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Currently while selecting a preferred frequency when no preference is
known, p2p_no_go_freq is not considered for 5 GHz and 60 GHz channels.
This results in starting GO on the channels that are configured not to
allow the local device as GO.
Use wpas_p2p_supported_freq_go api to check if the p2p_no_go_freq
configuration before selecting the preferred frequency for GO.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
For some 6 GHz operating class like 134, there is a possibility where
the ch variable used for channel iterator overflows when it is
incremented. Fix this by updating the datatype of ch variable to
avoid integer overflow while incrementing.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Generate an event on the control socket interface when a network is
added or removed. The event name CTRL-EVENT-NETWORK-<ADDED|REMOVED>
is followed by the network entry identifier. The event matches the
corresponding Network<Added|Removed> signal on the d-bus interface.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
The --conf option specifies a file containing a list of options
to configure the network used for running the test which will be
used in place of the defaults built into the script.
Signed-off-by: Nick Porter <nick@portercomputing.co.uk>
"SET disable_mscs_support 1" can be used to disable indication of MSCS
support in the Extended Capabilities element for testing purposes. This
is also disabling addition of the MSCS element even if valid
configuration parameters had been configured.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
"SET disable_scs_support 1" can be used to disable indication of SCS
support in the Extended Capabilities element for testing purposes.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
