FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.
If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.
Signed-off-by: Jouni Malinen <j@w1.fi>
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.
Signed-off-by: Vinit Deshpande <vinitd@google.com>
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
This wmm_ac_status command will show the current status for WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
These key management options were missing from the previous set of
parsed information in scan results.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 86bd36f0d5 ("Add generic
mechanism for adding vendor elements into frames") has a minor bug
where it miscalculates the length of memory to move using
os_memmove. If multiple vendor elements are specified then this can
lead to out of bounds memory accesses.
This patch fixes this by calculating the correct length of remaining
data to shift down in the information element.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
It also allows to use the STATUS command with default behavior,
say for debug, i.e., don't generate a "fake" CONNECTION and
SUPPLICANT_STATE_CHANGE events with the new STATUS-NO_EVENTS case.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
