This parameter was used in some of the NFC test cases to make scanning
more robust in case of changing AP configuration. However, the parameter
was not cleared anywhere, so it could have been left in use for other
test cases as well. To get more consistent behavior, clear the value
back to its default between test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to use instances of control interfaces in common
code without having to separately address hostapd and wpa_supplicant
behavior differences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that GO is able to complete group formation even if the
P2P Client does not send WSC_Done message (or that message is dropped
for any reason) in case the P2P Client completes 4-way handshake
successfully.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids unexpected connection attempts in cases a matching network
is enabled and there is no existing connection (e.g., when testing with
ENABLE_NETWORK no-connect option).
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow three P2P_FIND attempts for discovering the GO on a non-social
channels since the single Probe Response frame can be missed easily
under heavy CPU load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP. In addition, check for ROAM/FT_DS failures to be
able to report errors more clearly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The single channel scan while associated to another AP and immediately
after starting the second AP can miss the Probe Response frame
especially under heavy CPU load. Avoid false error reports by allowing
multiple scan rounds to be performed. wpas_ctrl_bssid_filter is also
modified to take into account different get_bss() behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface issues to be caught in a bit more readable
way in the debug logs. In addition, dump pending monitor socket
information more frequently and within each test case in the log files
to make the output clearer and less likely to go over the socket buffer
limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that AP acts on 40 MHz intolerant STA association/disassociation
and on 20/40 co-ex report indicating 40 MHz intolerant AP showed up and
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_multi_cred_sp_prio verifies that two credentials
provisioned by a single SP are selected properly based on sp_priority
when a single BSS matches both credentials.
test_ap_hs20_multi_cred_sp_prio2 does the same when there a separate BSS
for each credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This seems to be needed in some cases to avoid issues in test cases that
assume there are no other ERs running.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
