Extend 'struct wpa_driver_scan_params' to allow higher layer to indicate
if minimal probe request content should be included by the driver as part
of the scan logic.
Implement this with driver_nl80211, by setting
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This is needed to allow the driver to know on which operating channel
(as specified by the link that is affiliated with AP MLD for the current
association) is used for transmitting TDLS Discovery Response. This
commit adds the link_id parameter to various functions, but does not
implement the driver interface change itself.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
Parse link id and station MLD address received from the driver in the
NL80211_CMD_NEW_STA event.
Set MLO information of the station to the sta_info and wpa_sm.
Co-authored-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to parse association link id and MLD address from the
NL80211_CMD_UPDATE_OWE_INFO event.
Set MLO information of the station to the sta_info and wpa_sm.
Use station association link address for sending DH IE info to the
driver.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Retrieve the puncturing bitmap sent by the driver in channel select
events for ACS when using the QCA vendor specific event.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to match the key configuration design with a single
netdev and the nl80211 driver interface.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In case of MLO AP and legacy client, make sure Management frame TX
status is processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the
status to the correct BSS. Store the link ID when transmitting
Managements frames and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of MLO AP and legacy client, make sure EAPOL TX status is
processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the EAPOL
TX status to the correct BSS. Store the link ID when transmitting EAPOL
frames over control interface and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
EAPOL frames may need to be transmitted from the link address and not
MLD address. For example, in case of authentication between AP MLD and
legacy STA. Add link_id parameter to EAPOL send APIs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed for the driver to know on which link it should transmit
the frames in MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This includes:
- Modifications of the driver API, to include the link ID as part
of 'struct hostapd_freq_params'.
- Modifications to nl80211 driver.
- Modifications for the driver wrappers.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
To be used in later patches, e.g., for link tracking etc.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support to indicate link reconfiguration event reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to indicate TID-to-link mapping changes reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add support to configure the allowed frequency list for AP operation
using a QCA vendor interface before NL80211_CMD_NEW_BEACON/
NL80211_CMD_START_AP. hostapd generates the allowed frequency list by
intersecting user configured frequency list and all the frequencies
advertised by the driver including disabled channels. If user doesn't
specify allowed frequency list, all the frequencies advertised by the
driver, including disabled channels, will be configured.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of
a nontransmitted BSSID profile, an EMA AP that transmits a Beacon
frame carrying a partial list of nontransmitted BSSID profiles
should include in the frame a Reduced Neighbor Report element
carrying information for at least the nontransmitted BSSIDs that
are not present in the Multiple BSSID element carried in that frame.
Add this support by splitting the reduced neighbor report (RNR) in as
many elements as the number of multiple BSSID elements. Each RNR element
excludes the non-transmitting profiles already included in the MBSSID
element at the same index. If present, the last additional group will
have the data common for all EMA beacons such as neighbor AP information
gathered through neighbor reports.
The hwsim test case he_ap_ema demonstrates this support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Retrieve the puncturing bitmap sent by the driver in channel switch
events and add a new member punct_bitmap in struct ch_switch to store
it.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Send the user configured puncturing bitmap to the driver.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Multi link stations are represented in the kernel using a single
station with multiple links and the first ADD_STA command also
creates the first link. Subsequent links should be added with
LINK_ADD commands.
Implement this logic and provide the required MLD information per
station/link.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a driver callback to add a link to an AP interface.
As the kernel removes all links on underline interface removal, there
is currently no need to support individual link removal.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
"multicast_to_unicast" and "hairpin_mode" are usually set outside of
hostapd. However, DFS channel change events pull the BSS out of the
bridge causing these attributes to be lost. Make these settings tunable
within hostapd so they are retained after the BSS is brought up again.
Signed-off-by: Anthony Refuerzo <anthony96922@gmail.com>
The flags that indicate that a channel is allowed for 80/160 MHz use
are divided according to the position of the control channel (e.g.,
HOSTAPD_CHAN_VHT_10_70, HOSTAPD_CHAN_VHT_30_50, etc.).
However, the position of the control channel does not add any extra
regulatory information because when trying to use a 80/160 MHz channel
all the desired bandwidth has to be allowed for 80/160 MHz use,
regardless of the control channel position.
In addition, these flags are set only if the driver reports one
regulatory rule that allows the entire 80/160 MHz bandwidth.
However, even when a 80/160 MHz channel is allowed, in some cases the
bandwidth will be split into several regulatory rules because
different segments of the bandwidth differ in other flags (that don't
affect the use of the bandwidth for VHT channels). So, in such cases
these flags will not be set, although VHT channels are allowed.
As the result, VHT channels will not be used although they are allowed
by the regulatory domain.
Fix this by introducing new flags that indicate if a 2 0MHz channel is
allowed to be used as a part of a wider (80/160 MHz) channel.
The new flags are set for each 20 MHz channel independently and thus
will be set even if the regulatory rules for the bandwidth are split.
A 80/160 MHz channel is allowed if all its 20 MHz sub-channels are
allowed for 80/160 MHz usage.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allows collecting and exposing more information about the station's
current connection from the kernel to the connection manager.
* Add an enum to represent guard interval settings to driver.h.
* Add fields for storing guard interval and dual carrier modulation
information into the hostap_sta_driver_data struct.
* Add bitmask values indicating the presence of fields.
* STA_DRV_DATA_TX_HE_DCM
* STA_DRV_DATA_RX_HE_DCM
* STA_DRV_DATA_TX_HE_GI
* STA_DRV_DATA_RX_HE_GI
* Retrieve NL80211_RATE_INFO_HE_GI and NL80211_RATE_INFO_HE_DCM in
get_sta_handler(), and set appropriate flags.
Signed-off-by: David Ruth <druth@chromium.org>
Enable MLO for SAE authentication when the driver indicates the AP MLD
address in an external authentication request. The MAC address of the
interface on which the external authentication request received will be
used as the own MLD address.
This commit does below for enabling MLO during external SAE
authentication:
- Use MLD addresses for SAE authentication.
- Add Basic Multi-Link element with the own MLD address in SAE
Authentication frames.
- Send SAE Authentication frames with the source address as the own MLD
address, destination address and BSSID as the AP MLD address to the
driver.
- Validate the MLD address indicated by the AP in SAE Authentication
frames against the AP MLD address indicated in external authentication
request.
- Store the PMKSA with the AP MLD address after completing SAE
authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
In case of drivers that offload the 4-way handshake to the driver, there
was no way of updating wpa_supplicant about the transition disable
bitmap received as a part of EAPOL-Key msg 3/4.
With latest provisions in cfg80211_port_authorized(), the TD bitmap can
be sent to the upper layer. Parse that as a part of the port authorized
event and set the transition disable information accordingly.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Check the HE membership selector and don't use the BSS
if required but not supported by HW.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Define additional association parameters for MLD to be able to indicate
information for all the requested links and fill these into nl80211
attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Set MLO attributes for NL80211_CMD_AUTHENTICATE and make sure that MLD
configuration is preserved between authentication retries.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Facilitate emitting more station information over D-Bus for use by the
connection manager.
* Add storage for more NL80211_STA_INFO_* fields to data structures, and
move them through the system.
* Reorder NL80211_STA_INFO_* fields in driver_nl80211.c to match the
ordering in nl80211.h.
* Convert signal field to an integer to support holding WPA_INVALID_NOISE
and avoid changing logging.
* Add fields to hostap_sta_driver_data to capture more information
* fcs_error_count
* beacon_loss_count
* expected_throughput
* rx_drop_misc
* rx_mpdus
* rx_hemcs
* tx_hemcs
* rx_he_nss
* tx_he_nss
* avg_signal
* avg_beacon_signal
* avg_ack_signal
* Add struct hostap_sta_driver_data to struct wpa_signal_info and remove
redundant fields and redundant attribute parsing
* Change logging when printing txrate to handle unsigned long
value
Signed-off-by: David Ruth <druth@chromium.org>
Add helper functions to retrieve the context for the transmitting
interfaces of the MBSSID set and the index of a given BSS.
Set device parameters: BSS index and the transmitting BSS.
Include Multiple BSSID elements in Beacon and Probe Response frames.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Retrieve driver capabilities for the maximum number of interfaces for
MBSSID and the maximum allowed profile periodicity for enhanced MBSSID
advertisement.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Add support to specify a Link ID for set key operation for MLO
connection. This does not change the existing uses and only provides the
mechanism for extension in following commits.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Currently only accepted MLO links information is getting parsed from
(re)association events. Add support to parse all the requested MLO links
information including rejected links. Get the rejected MLO links
information from netlink attributes if the kernel supports indicating
per link status. Otherwise get the rejected MLO links information by
parsing (Re)association Request and Response frame elements.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Fetch the MLO association Link ID info from the driver to the
wpa_supplicant instance of the corresponding MLD STA interface. This
info is needed when setting the MLO connection info to wpa_sm.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Parse link id info from channel switch events and indicate the info to
control interface using new per link channel switch events. If channel
switch happens on the link which used during association both legacy
and new per-link channel switch events will be reported.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch and indicate per-link MLO signal poll information
via a new control interface command MLO_SIGNAL_POLL.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch MLO connection info from the driver to the
wpa_supplicant instance of corresponding MLD STA interface. In addition,
return true for BSSs associated with MLO links from wpa_bss_in_use() to
avoid getting them cleared from scan results.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Parse NL80211_ATTR_MLO_LINKS in NL80211_CMD_CONNECT event and cache the
MLO connection information. Set the legacy connection fields such as
assoc_freq and bssid to the values of the MLO link on which association
happened.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
This brings in the function declarations and data structures that are
required for handling PASN request from the driver, sending secure
ranging context and PASN response to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
