Fix references to the appropriate driver capability drv_flags2. The
initial version used the incorrect drv_flags value and by doing so,
ended up using incorrect driver capabilities (DEAUTH_TX_STATUS,
BSS_SELECT, TDLS_SUPPORT) which could result in incorrect OWE
functionality for both AP and STA cases.
Fixes: d984c7b298 ("hostapd: Add support for OWE offload for STA/AP interface")
Fixes: da364180fb ("hostapd: Support 4-way handshake offload for AP/P2P GO")
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The driver advertising SAE AP offload support would take care of SAE
authentication and PMK generation at the driver/firmware. This feature
requires the driver to be supporting 4-way handshake offload to process
the generated PMK at the driver level for 4-way handshake.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The driver advertising OWE offload support would take care of
Diffie-Hellman Parameter element generation and processing part. The
driver would be responsible for OWE PMK generation in this case.
Avoid the Diffie-Hellman Parameter element handling in
wpa_supplicant/hostapd for drivers advertising OWE offload support. This
change is applicable only for drivers supporting 4-way handshake
offload.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Add support for offloaded 4-way handshake in AP/P2P GO mode. For drivers
supporting the AP PSK offload, wpa_supplicant/hostapd passes down the
PSK for the driver to handle the 4-way handshake. The driver is expected
to indicate port authorized event to indicate that the 4-way handshake
is completed successfully.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The max transmit power of Standard Power (SP) Access Points (AP) on
6 GHz band and APs on 2.4 GHz and 5 GHz bands is limited by effective
isotropic radiated power (EIRP), while the max transmit power of Low
Power Indoor (LPI) APs on 6 GHz Band is limited by power spectral
density (PSD). Therefore the max transmit power of LPI APs grows as the
channel width increases, similar to the noise power which has constant
PSD.
Adjust the SNR of BSSes based on the transmit power config and max
channel width. EIRP limited APs usually have constant max transmit power
on different channel widths, their SNR decreases on larger channel width
because the noise power is higher, while PSD limited APs have constant
SNR over all channel widths.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
This adds the newer driver capability "flags2" bitmask to the
hostapd_cli/wpa_cli "status driver" result.
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
This was already done for driver_flags, but the newer driver_flags2 was
not covered here.
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Populate the switch case in the driver_flag2_to_string() function with
the full list of feature MACROs represented with the "flags2" bitmask.
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Set WPA_DRIVER_FLAGS2_SAE_OFFLOAD flag if the driver indicates SAE
authentication offload support for STA mode. Allow SAE password to be
provided to the driver in such cases when using the CONNECT command.
Signed-off-by: Chung-Hsien Hsu <chung-hsien.hsu@infineon.com>
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Add support for Authentication negotiated over IEEE Std 802.1X
with key derivation function using SHA-384.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Presence of any 6ghz channels indicates nl80211 driver 6 GHz support,
not non-DISABLED channels. This increases the timeout for scan
completion for cases where 6 GHz might get scanned even if all the
channel there are currently DISABLED.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
A driver may not support setting MAC address when interface is UP, so
wpa_supplicant used to always sets the interface down for MAC address
change.
Try to change the address first without setting the interface down and
then fall back to DOWN/set addr/UP if the first attempt failed. This can
reduce the interface setup time for time-critical use cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend 'struct wpa_driver_scan_params' to allow higher layer to indicate
if minimal probe request content should be included by the driver as part
of the scan logic.
Implement this with driver_nl80211, by setting
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Previously the NL80211_CMD_SET_QOS_MAP command was sent to the radio
interface. Send this command using nl80211_cmd_msg() and the bss,
instead of drv.
Signed-off-by: Arnon Meydav <ameydav@maxlinear.com>
For now, only a vendor command is available for this functionality that
is needed to implement single-link TDLS during an MLO association.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to allow the driver to know on which operating channel
(as specified by the link that is affiliated with AP MLD for the current
association) is used for transmitting TDLS Discovery Response. This
commit adds the link_id parameter to various functions, but does not
implement the driver interface change itself.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
Typecasting takes precedence over division here, so the legacy rates
larger than 255 * 100 kbps (i.e., 36, 48, 54 Mbps) ended up getting
truncated to invalid values.
Fix this by typecasting the value after the division.
Fixes: d4f3003c56 ("nl80211: Configure Beacon frame TX rate if driver advertises support")
Signed-off-by: Prasanna JS <quic_pjs@quicinc.com>
Pass bss->ctx instead of drv->ctx in order to avoid multiple reports for
the first bss. The first report would otherwise clear hapd->cca_color and
subsequent reports would cause the iface bss color to be set to 0.
In order to avoid any issues with cancellations, only overwrite the color
based on hapd->cca_color if it was actually set.
Fixes: 33c4dd26cd ("BSS coloring: Handle the collision and CCA events coming from the kernel")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Parse link id and station MLD address received from the driver in the
NL80211_CMD_NEW_STA event.
Set MLO information of the station to the sta_info and wpa_sm.
Co-authored-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add check to skip the STA mode specific MLO link channel switch handling
in AP mode. Commit 1b6f3b5850 ("MLD STA: Indicate per link channel
switch") added this indication only for STA mode.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Add support to parse association link id and MLD address from the
NL80211_CMD_UPDATE_OWE_INFO event.
Set MLO information of the station to the sta_info and wpa_sm.
Use station association link address for sending DH IE info to the
driver.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Retrieve the puncturing bitmap sent by the driver in channel select
events for ACS when using the QCA vendor specific event.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, NL_STOP was returned from the survey dump handler if the
maximum number of frequencies was reached for storing survey
information, but this is causing wpa_supplicant context getting stuck if
the current SKB returned by the kernel itself ends with NLMSG_DONE type
message. This is due to libnl immediately stopping processing the
current SKB upon receiving NL_STOP and not being able to process
NLMSG_DONE type message, and due to this wpa_supplicant's
finish_handler() not getting called. Fix this by returning NL_SKIP
instead while still ignoring all possible additional frequencies.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
This is needed to match the key configuration design with a single
netdev and the nl80211 driver interface.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In case of MLO AP and legacy client, make sure Management frame TX
status is processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the
status to the correct BSS. Store the link ID when transmitting
Managements frames and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of MLO AP and legacy client, make sure EAPOL TX status is
processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the EAPOL
TX status to the correct BSS. Store the link ID when transmitting EAPOL
frames over control interface and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed since link_id is not always available. In addition,
recognize the link address as a known address.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
EAPOL frames may need to be transmitted from the link address and not
MLD address. For example, in case of authentication between AP MLD and
legacy STA. Add link_id parameter to EAPOL send APIs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed for the driver to know on which link it should transmit
the frames in MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In MLO, multiple BSSs can transmit on different frequencies. Select
link frequencies according to the transmitter address.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This includes:
- Modifications of the driver API, to include the link ID as part
of 'struct hostapd_freq_params'.
- Modifications to nl80211 driver.
- Modifications for the driver wrappers.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
To be used in later patches, e.g., for link tracking etc.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Retrieve the EML capabilities as well as the MLD capabilities and ops
from nl80211 and expose them using the new driver interface
get_mld_capa().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
We will start using this structure to also track MLD related
capabilities instead of just extended capabilities. As such, give the
structure a more generic name.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Add support to indicate link reconfiguration event reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to indicate TID-to-link mapping changes reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The current value of 50 is not sufficient for getting survey info for
all the frequencies when the 6 GHz band is enabled. Increase the limit
to 100 to be able to receive survey info for 6 GHz frequencies also.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
This adds more production-like testing coverage for KDK derivation. Both
SAE and OWE transition mode are covered. The latter has some corner
cases that did not work correctly previously.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to configure the allowed frequency list for AP operation
using a QCA vendor interface before NL80211_CMD_NEW_BEACON/
NL80211_CMD_START_AP. hostapd generates the allowed frequency list by
intersecting user configured frequency list and all the frequencies
advertised by the driver including disabled channels. If user doesn't
specify allowed frequency list, all the frequencies advertised by the
driver, including disabled channels, will be configured.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add new nested netlink attribute, NL80211_ATTR_EMA_RNR_ELEMS, to send
the reduced neighbor report (RNR) elements to the driver when EMA is
enabled. This attribute includes the count of RNR elements and data at
each index. While generating EMA beacons, the driver will include RNR
group at a given index along with MBSSID group. The last element, if
present, has RNR data common for all EMA beacons such as neighbor APs.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of
a nontransmitted BSSID profile, an EMA AP that transmits a Beacon
frame carrying a partial list of nontransmitted BSSID profiles
should include in the frame a Reduced Neighbor Report element
carrying information for at least the nontransmitted BSSIDs that
are not present in the Multiple BSSID element carried in that frame.
Add this support by splitting the reduced neighbor report (RNR) in as
many elements as the number of multiple BSSID elements. Each RNR element
excludes the non-transmitting profiles already included in the MBSSID
element at the same index. If present, the last additional group will
have the data common for all EMA beacons such as neighbor AP information
gathered through neighbor reports.
The hwsim test case he_ap_ema demonstrates this support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
