Commit e9c3c1afed added a new D-Bus
method and that was enough to push the Introspect XML buffer over
the previously allocated 8000 bytes. Increase the buffer size to
make enough room for P2P interface. In addition, add a debug
message to indicate if an XML segment does not fit into the buffer
to make this types of failures somewhat easier to catch.
Signed-hostap: Jouni Malinen <j@w1.fi>
IEEE Std 802.1X-2004 does not clear authWhile and heldWhile in this
case, but doing so allows the timer tick to be stopped more quickly when
the port is not enabled. Since these variables are used only within HELD
and RECEIVE states, clearing them on initialization does not change
actual state machine behavior. This reduces some unnecessary operations
in port disabled state and cleans up the wpa_supplicant debug log after
disconnection.
Signed-hostap: Jouni Malinen <j@w1.fi>
The authentication timeout could be triggered after the connection has
already been known to have failed. The event at that point can be
confusing, so better cancel the timeout when processing connection
failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSSID of the AP is specified in the WPS command, the target
AP is likely already in the BSS table and its operating channel is
known. Use this information to speed up connection by only scanning
the known channel.
Signed-hostap: Jouni Malinen <j@w1.fi>
The 'network.target' is special (per systemd.special(7)), and is to be
brought up indirectly when network is actually configured (i.e. through
DHCP or static address settings).
Irrelevant of that, all services should be always installed in
multi-user.target.
[Bug 427]
Since wps_registrar_pbc_timeout is called to stop PBC, previously
registered wps_registrar_pbc_timeout must be canceled when canceling
the WPS operation.
Signed-off-by: Spencer Chang <jungwalk@gmail.com>
The offchanok parameter is hardcoded to one in number of paths and that
added NL80211_ATTR_OFFCHANNEL_TX_OK attribute to NL80211_CMD_FRAME
unconditional. cfg80211 rejects this with EINVAL if the driver does not
indicate support for offchannel TX. Fix this by not requesting
offchannel TX depending on driver capabilities. Remain-on-channel
operation was used for those cases anyway, so the additional attribute
was not really needed for these in the first place.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes issues with drivers that do not handle concurrent
remain-on-channel and scan operations in a case where Provision
Discovery Response frame is not received to stop the Action frame
handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the freq parameter is specified and we are already running legacy STA
on a different frequency with a driver that does not support
multi-channel concurrency, reject p2p_group_add. Same code already
exists in the path of P2P connection with go negotiation but is missing
for autonomous GO.
Signed-hostap: Neeraj Garg <neerajkg@broadcom.com>
When nl80211_setup_ap() has enabled Probe Request reporting, this must
not be disabled when P2P Listen state is stopped to avoid breaking AP
mode operations. This could happen, e.g., if a Probe Request frame was
received from a P2P device that the we are trying to invite to our group
(i.e., when operating in GO role). p2p_probe_req_rx() calls
p2p_invite_start() in this case and that ends up calling
p2p->cfg->stop_listen() which calls probe_req_report() driver op.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd uses the poll method to check if the station is alive
after the station has been inactive for ap_max_inactivity seconds.
Make the poll mechanism configurable so that user can choose to
disconnect idle clients.
This can be especially useful when some devices/firmwares have
restrictions on the number of clients that can connect to the AP
and that limit is smaller than the total number of stations trying
to use the AP.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The 100 ms timeout on retransmitting group key message can be too short
for stations that are in power save mode or if there is a large number
of association stations. While the retransmission of the EAPOL-Key frame
should allow this to be recovered from, it is useful to avoid
unnecessary frames to save soem CPU and power.
Signed-hostap: Jouni Malinen <j@w1.fi>
Drivers that use device SME in AP mode may still need to be
subscribed for Action frame RX when monitor interface is not used.
This fixes number of P2P GO operations with ath6kl.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Poll command may be enough for mac80211 to figure out whether monitor
interface is to be used, but this change did not take into account
non-mac80211 drivers that support AP mode without monitor interface.
For example, ath6kl needs to get use_monitor disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.
For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P module provides access to public peer data in struct
p2p_peer_info. Use this to build the P2P_PEER information in
ctrl_iface.c instead of providing such text format data from the P2P
module.
The internal data that was previously built in p2p_get_peer_info() as
part of the text format peer data is now available through a separate
p2p_get_peer_info_txt() function. This is still included in P2P_PEER
output to maintain backwards compatibility with external programs that
could have started to use this. However, it should be noted that this
data is not really supposed to be used for anything else apart from
debugging purposes and its format is subject to change.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_get_peer_info() was used in multiple places just to check whether a
specific peer is known. This was not the designed use for the function,
so introduce a simpler function for that purpose to make it obvious that
the p2p_get_peer_info() function is actually used only in ctrl_iface.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
KEK from TPTK needs to be used instead of from PTK when processing
rekeying case similarly to what was already done with KCK.
Signed-hostap: Jouni Malinen <j@w1.fi>
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If p2p_listen is issued during a p2p_scan, a pending after-scan operation
is scheduled. However, since there is support for only a single pending
operation, this was able to override a previously scheduled pending
connect command. This can break some command sequences, so give higher
priority to pending connect operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The active station connection triggered wpa_supplicant AP mode startup
to try to update Beacon IEs before the AP mode was properly initialized
and that resulted in NULL pointer dereference in driver_nl80211.c. Fix
this by skipping the IE update before the AP mode is initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Android ICS system/core/libnl_2 has very limited genl_ctrl_resolve()
implementation that cannot handle names other than nlctrl. Work
around that by implementing more complete genl_ctrl_resolve()
functionality within driver_nl80211.c for Android builds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.
The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.
Signed-hostap: Jouni Malinen <j@w1.fi>
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.
Signed-hostap: Jouni Malinen <j@w1.fi>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
I needed this patch to compile against the latest
libnl code. I added this to my config file:
CONFIG_LIBNL32=y
Signed-hostap: Ben Greear <greearb@candelatech.com>
When waiting for go_neg frame from the peer in WAIT_PEER_CONNECT state,
I have observed that sometimes it takes 20 to 30 secs for successful GO
negotiation. I also found out that it is because of 1 second idle time,
in WAIT_PEER_CONNECT state. While it is good to have 1 second idle time
[for doing power-save or doing some other legacy STA Scan or some other
useful stuff], this makes GO Negotiation process slow.
We wait for 1 second idle and then listen for a random time between
100(min)-300(max) ms. Assume P1 is in WAIT_PEER_CONNECT state and P2 is
the one which is now to send go_neg frame. If P2 sends GO Negotiation
frame just at the boundary of 300 ms of P1 and assume that P2 takes
close to 600-800 ms for one iteration of sending go_neg request (one
iteration is GO Negotiation Request frame time + dwell time +
listen_time), P2 needs to transmit at least 16-18 Action frames for
hitting the listen time of P1.
Following patch reduces the idle time to 500 ms. Alternatively we can
increase the listen time interval to 500 ms just for WAIT_PEER_CONNECT
state.
Provision discovery from a known peer should actually check for
dev->flags & P2P_DEV_PROBE_REQ_ONLY. This is creating an issue of
updating the listen frequency of peer with the PD request frame
frequency. PD request frame will be sent by the peer on our local listen
frequency. This patch fixes that error. Suggested check has already been
implemented in the invitation req receive path.
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.
Signed-hostap: Jouni Malinen <j@w1.fi>
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). WPS.Start() call can be used to initiate WPS negotiation
similarly to how this is done in station mode.
This was done to ctrl_iface by Jouni Malinen on April 21, 2009 (commit
3ec97afe57)
Signed-hostap: Gustavo Sverzut Barbieri <barbieri@profusion.mobi>
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).
It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.
Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When the station is connected to P2P GO after calling p2p_find command
the device sees itself. It is related to lack of filtering itself from
clients connected to P2P GO.
Step by step:
1. dev1: p2p_group_add
2. dev2: p2p_connect <MAC1> pbc join
3. dev1: wps_pbc
4. dev2: p2p_find
Skip P2P client information for our own device from a GO with which
we are connected.
It looks like some USIM cards respond with 0x67 (Wrong length) instead
of 0x6c to 00 b2 01 04 ff. This was getting rejected in
scard_get_record_len(). ETSI TS 102 221 is not very clear on this
detail, but it looks fine to accept the 0x67 error value, too, to learn
the record length.
Signed-hostap: Jouni Malinen <j@w1.fi>
Need to remove ROAM command processing since the needed functionality
for it gets removed with CONFIG_NO_SCAN_PROCESSING=y.
Signed-hostap: Jouni Malinen <j@w1.fi>
The whole wpa_supplicant_ctrl_iface_ctrl_rsp_handle() function operates
on the ssid->eap field which exists only if IEEE8021X_EAPOL has been
defined. Therefore the whole function body needs to be enclosed within
an #ifdef/endif block.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Return 1/0 instead 0/-1 to indicate valid/invalid element so that
the if statement makes more sense with !wmm_valid().
Signed-hostap: Jouni Malinen <j@w1.fi>
