A new vendor attribute QCA_WLAN_VENDOR_ATTR_GET_WEIGHED_PCL is added for
getting preferred channels with weight value and a flag to indicate how
the channels should be used in P2P negotiation process.
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Indicates the driver to use the RSNE as-is from the connect interface.
Exclusively used for the scenarios where the device is used as a testbed
device with special functionality and not recommended for production.
This helps driver to not validate the RSNE passed from user space and
thus allow arbitrary IE data to be used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously commit c79238b6a4 ('Define a
QCA vendor command to configure SAR Power limits') implemented a vendor
command interface to allow a userspace entity to dynamically control the
SAR power limits. Now implement a command to retrieve the current SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL is added
for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
This attribute is for setting the level of WLM.
Signed-off-by: Paul Zhang <paulz@qti.qualcomm.com>
Add QCA vendor command and attributes for vendor specific Representative
RF Operating Parameter (RROP) information. This information is intended
for optional use by external ACS. It provides guidance values for some
RF parameters that are used by the system during operation, so that
external ACS can utilize these to compare between channels, bands, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix the block comment style issue introduced as part of commit
fbfceef3af ("Add QCA vendor commands for
spectral scan").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add sub-command QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING to flush
pending packets in firmware. The attributes are listed in enum
qca_wlan_vendor_attr_flush_pending. The QCA_WLAN_VENDOR_ATTR_PEER_ADDR
specifies the peer MAC address and the QCA_WLAN_VENDOR_ATTR_AC specifies
the access category of the pending packets.
Signed-off-by: Lin Tingting <tinlin@qti.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
is added for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET.
This attribute is for pending MSDUs corresponding to respective AC.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Add the following vendor commands and their vendor attributes for
spectral scan.
1) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
Get current values of spectral parameters.
2) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
Get stats for spectral scan debug.
3) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
Get the spectral hardware capability.
4) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
Get the current status of spectral scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
and QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME to record
timestamp and duration for the last MAC counters. Some user layer
application is delay sensitive. It needs to know time stamp and
measurment duration for the counters.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Add additional attributes to specify the PMK, PMKID, and the ERP next
sequence number to the vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH. These are needed in case
of an offloaded FILS roaming.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add 802.11ax channel property flags for use with external ACS (QCA
vendor command). Use the remaining available bits in
qca_wlan_vendor_channel_prop_flags for the first few 11ax flags. Then
add qca_wlan_vendor_channel_prop_flags_2 as a continuation of
qca_wlan_vendor_channel_prop_flags and add the remaining 11ax flags
there. Note that qca_wlan_vendor_channel_prop_flags_ext is not used
since it is currently not intended for holding such information. Rather
it is meant for holding additional control information related to
features such as DFS, CSA, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FILS features on STA needs to be disabled for testing purposes to
verify the APUT behavior with non-FILS STAs. Add a QCA vendor attribute
for doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an event indicating to the user space that the driver has
detected an internal failure. The driver is expected to recover from
such a failure automatically, e.g., by resetting the device. This event
carries the information indicating the reason that triggered this
detection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This request ID was wrongly referred from the REQUEST_ID in
enum qca_wlan_vendor_attr_gscan_config_params which is mapped to
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM in PNO Config.
Hence define a different attribute to represent the request ID
for PNO Config.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The attribute is QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE, not
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS to specify
the active Type Of Service on the specific interface. This can be used
to modify some of the low level scan parameters (off channel dwell time,
home channel time) in the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit renames the vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_OFFCHANNEL to
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL as intended by the
original commit d506c35efc ('Set Wi-Fi
Configuration attribute to restrict offchannel operations').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION -
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL which can be used to
restrict offchannel operations on the AP/GO interface.
The goal is to restrict any operations which would cause the AP/GO to
leave its operating channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the following two attributes to
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH events:
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS - Indicates the status of
re-association requested by user space
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION - Indicates whether
the old association was maintained when a re-association
is requested by user space and that re-association attempt
fails (i.e., cannot connect to the requested BSS, but can
remain associated with the BSS with which the association was
in place when being requested to roam).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL which allows the currently
used listen interval to be updated using
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION. This update applies
only during the association and is done without updating the AP about
the change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to signify the preferred
channel list policy for external ACS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add new vendor commands for starting and stoppping spectral scan. Add
vendor attributes for configuring spectral scan parameters as part of
the start command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add attribute for TA max duration after last TA received. So that local
time is synchromous to other communicating OCB STAs. If the duration
expires, OCB STA without UTC time source is not in sync to other STAs
and stop scheduling DSRC channel switch after max duration.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
Document QCA vendor OCB commands about IEEE Std 802.11 communication
outside the context of a basic service set. Also define all attributes
for the specific OCB commands.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
1. Add new attribute to report corresponding antenna information to the
chain RSSI which is used in subcmd
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI.
2. Add a series of attr to support the new wmi interface
WMI_PDEV_PARAM_ANT_DIV_USRCFG which export parameters setting of antenna
diversity algorithm to userspace.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY is added to set
propagation delay's absolute value. This is a more detailed version of
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Add QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT for setting the number
of antennas that will be active in different modes for each connection.
Signed-off-by: Alexei Avshalom Lazar <qca_ailizaro@qca.qualcomm.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH.
This attribute can set a station device to work in 5 or 10 MHz channel
width while in disconnect state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the vendor command to set the trace level
for the respective QCA host driver module.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands and attributes
for fetching BSS transition status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces QCA vendor commands and the corresponding
attributes to set/get NUD (Network Unreachability Detection) statistics.
The set NUD statistics configures the requisite parameters to the host
driver and thereby triggers the start/stop of collection of statistics.
The get stats fetches the statistics collected in the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines a QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE that carries required
information leading to the power save failure. This will be an event
from the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the QCA vendor command and the attributes which
facilitate the host driver to use an external user space entity for
performing automatic channel selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID extension. The payload of
these vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit documents the QCA vendor commands 61-73 and the
corresponding definitions of the attributes. This set of commands were
previously reserved for QCA without documentation here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These thresholds values indicate how many Beacon frames can be missed
before before disconnecting from the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c79238b6a4 ('Define a QCA vendor
command to configure SAR Power limits') had a mismatch between the enum
qca_vendor_attr_sar_limits_selections documentations and actual values.
The BDF SAR profiles are 0-based, so rename the enum values and reorder
the values keep the actual values more convenient. While this changes
values over the interface, this is justifiable since the new command was
introduced only recently and it had not been released in any driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is a regulatory requirement for Specific Absorption Rate (SAR)
whereby the device transmit power is reduced when it is determined that
the device is in close proximity to the body. Implement a vendor command
interface to allow a userspace entity to dynamically control the SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN command can be used to
abort an ongoing scan that was started with
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
