In the send_assoc_resp() function, there’s a chance that the sta
argument could be NULL. Therefore, it’s crucial not to directly
dereference sta without first checking whether it’s a valid pointer.
However, commit 58ac46baf7 (“WNM: AP configuration to allow BSS max
idle period requests”) introduces direct dereferencing of max idle
period from sta, which might lead to a NULL pointer dereference. Fix
this now.
Fixes: 58ac46baf7 ("WNM: AP configuration to allow BSS max idle period requests")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Bandwidth Indication subelement contains channel bandwidth, channel
center frequency, and optionally punctured subchannels.
As per IEEE P802.11be/D7.0, 35.15.3 (Channel switching methods for an
EHT BSS), if a Channel Switch Announcement element or an Extended
Channel Switch Announcement element is used to announce a switch to an
EHT BSS operating channel width wider than 160 MHz or to an EHT BSS
operating channel width including at least one punctured 20 MHz
subchannel, the Bandwidth Indication subelement in the Channel Switch
Wrapper element shall be present in the same frame.
Hence, add it into the Beacon and Probe Response frames under the above
mentioned conditions.
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Wide Bandwidth Channel Switch subelement was directly appended in
the Channel Switch Wrapper element function
hostapd_eid_wb_chsw_wrapper(). However, a subsequent change would add
Bandwidth Indication subelement in the Channel Switch Wrapper element.
Hence using the same function name would be confusing.
Hence, refactor the current code into two functions. The first function
hostapd_eid_chsw_wrapper() forms the channel switch wrapper element.
This calls hostapd_eid_wb_channel_switch() to add a Wide Bandwidth
Channel Switch subelement inside it.
No functionality change.
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
During MLO, an nl80211_cqm_event may be received by any BSS. Directing
this event to the first BSS may not be suitable as it might not
correspond to the link the event is meant for. Hence, there is a need to
handle this on per-BSS basis.
Therefore, handle nl80211_cqm_event per BSS. The event handler further
uses the address information present in the event to fetch the intended
link BSS if no matching STA entry was found based on the initial
ap_get_sta() call.
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The hostapd_find_by_sta() function may be utilized by multiple driver
events. Therefore, it should be declared at the outset to ensure
accessibility by all event handlers.
No functional changes.
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Max Channel Switch Time element indicates the time delta between the
time the last beacon is transmitted by the AP in the current channel and
the expected time of the first Beacon frame transmitted by the AP in the
new channel.
IEEE P802.11be/D7.0, 35.3.11 (ML procedures for (extended) channel
switching and channel quieting) indicates that if an AP affiliated with
an AP MLD is switching channel, Max Channel Switch Time element shall be
included in every Beacon and Probe Response frame it transmits.
Add support to include the Max Channel Switch Time element in Beacon and
Probe Response frames during channel switch announcement for an AP
affiliated with an AP MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
These can be used outside the context of FST and hostapd.c, so move the
macro definitions into a shared header file. In addition, fix the
currently unused US_TO_TU() definition and rename "US" to "USEC".
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, hapd->link is added to the MLD links list during driver
initialization and setup BSS operation. However, a call trace has been
observed where a BSS link item is not present in the list and an attempt
is made to delete it from the list. This scenario occurs during the
deinitialization operation, which calls hostapd_bss_link_deinit() and
tries to remove the hapd->link which is not present in the list.
Ensures that the link item is added to the list only after the
successful operation of link addition. Also ensure that mld->num_links
increments only when the addition is successful. Therefore, return from
hostapd_bss_link_deinit(), if mld->num_links is zero. Since the mld
object is shared among all the links, num_links has to be incremented
only when the addition is successful.
Call trace:
dl_list_del.lto_priv.9.lto_priv ()
hostapd_bss_link_deinit.lto_priv ()
hostapd_bss_deinit ()
hostapd_interface_deinit ()
hostapd_interface_deinit_free ()
hostapd_main ()
Signed-off-by: Sidhanta Sahu <quic_sidhanta@quicinc.com>
hostapd used to always enable only the group 19 when SAE groups were not
configured explicitly in hostapd.conf. This may cause undesired
connection delay with STAs which use group 20 as the primary group with
SAE-EXT-KEY AKM during SAE authentication attempt.
To avoid this, enable group 20 in default groups when AP supports
SAE-EXT-KEY and SAE groups have not been configured explicitly in
hostapd.conf.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Currently only one scan can be performed on per phy level at a time in
the driver. Due to this, if another scan request is sent via anoother
underlying phy, the kernel returns -EBUSY. This would result in hostapd
trying to set the interface into station mode if it was originally in AP
mode and retry sending a scan request. However, this behavior is
expected in case of multi link operation and hence there is no need to
switch the mode as such.
Hence, add logic to not change the NL mode if the kernel returns -EBUSY
during multi link AP operation. The caller can accordingly decide and,
if needed, it can re-schedule a scan request after some time.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, whenever a scan is started, it uses drv's first BSS only
whether it is AP or STA interface. However, with AP MLD related changes,
the same drv could be used by other BSSs as well which needs scanning.
Hence, the current logic will not work since scan needs to be handled on
a non-first BSS as well.
Move the logic of always using drv's first BSS during scan events to
using BSS on which the event arrived.
Also, for AP MLD operation, even though the BSS is same, the link BSS
also needs to be identified. Hence, add a back pointer in the BSS struct
which would be used to point to the link BSS which requested the scan on
that BSS. This will help in routing the scan events to an appropriate
BSS ctx.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
hostapd would send DISASSOC packet (after quiet DEAUTH) or DEAUTH packet
(after quiet DISASSOC) to the station after some inactivity timeout,
even though the command has tx=0 parameter. Fix this so that tx=0 cleans
the STA info without sending any DISASSOC or DEAUTH packets.
Signed-off-by: Gal Savion <gsavion@maxlinear.com>
This can be used with a clangd server to get code completion and cross
references in editor. To simplify the generation, create .cmd files for
most object files while building that contains the base directory and
command that was used when compiling it.
A very simple gen_compile_commands.py is provided which will read one or
more build directories and generate the compile_commands.json file for
it.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Add a new vendor attribute
QCA_WLAN_VENDOR_ATTR_SCAN_SKIP_CHANNEL_RECENCY_PERIOD for sub command
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN to skip the recently scanned
channels within specified time (in ms), thus reducing the number of
channels for requested scan.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
The value currently is simply incremented, but it must not
reach 255 and rather wrap around from 254 to 0, since in
the Reduced Neighbor Report 255 means unknown. Fix that.
Fixes: d95838b793 ("AP: Add support for testing ML link removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Link Id attribute is required for
qca_wlan_vendor_attr_external_acs_event to identify the link on which
the command is received for an AP MLD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_LINKID attribute to the
ADD_STA_NODE command to identify a specific link affiliated to an AP
MLD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new sub command QCA_NL80211_VENDOR_SUBCMD_AUDIO_TRANSPORT_SWITCH
to request the audio data transport switch in both the command and event
path. This is used when two or more audio data transports are available
between peers.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
The driver might delete the STA node details on receiving external auth
status. In SAE authentication failure case on the AP, an Authentication
frame with a failure status is sent to the driver after sending the
external auth status. Authentication frame transmission didn't have a
dependency with STA node details earlier, but with MLO, Authentication
frames should be transmitted using the link address for a given MLD MAC
address by the supplicant. Since MLD to link address translation is done
by the driver, the STA node details are required to transmit the
Authentication frame. Hence, send external auth status to the driver
after sending the Authentication frame.
SAE external auth was introduced in commit 4ffb0fefe4 ("hostapd:
Support external authentication offload in AP mode"), which requires the
change in order of sending Authentication frame and auth status in case
of failure when using MLO.
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Use the RSN Override Link KDE to include the override variants of the
RSNE/RSNXE for each link so that all variants are verifies when
processing the protected EAPOL-Key message 3/4.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows all variants to be verified based on a protected frame to
achieve robust downgrade protection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This provides an implicitly protected (SNonce is used as an input to PTK
derivation) mechanism for a STA to indicate support for RSN overriding
in a manner that does not cause interopability issues with deployed APs.
In addition, update sm->SNonce on the Authenticator only based on
message 2/4 since that is the only EAPOL-Key message that is defined to
provide the actual SNonce value. While clearing of this internal buffer
on message 4/4 might not cause issues, it is better to keep the actual
SNonce value here since the SNonce cookie can be used at a later point
in the sequence.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This replaces the use of the RSNE Override and RSNE Override 2 elements
with empty payload to indicate which RSNE variant was used.
In addition, this adds stricter validation of the RSNE in
(Re)Association Request frame to allow only the pairwise cipher suites
and AKMs listed in the indicated RSNE variant to be used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The separate RSNOE/RSNO2E/RSNXOE buffers were not actually used on the
Authenticator, so remove them.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
hostapd_eid_assoc_fils_session() might return NULL if memory allocation
fails. This NULL value then will be used for invalid calculation and
cause unspecified behavior or be dereferenced unexpectedly. Avoid this
with an explicit check of the returned pointer.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Use else-if check for better clarity regarding usage of wpa_ie_buf3 to
make it explicit that memory is allocated for this pointer only once.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
The new hostapd configuration parameter eapol_key_reserved_random=1 can
be used for testing STA/Supplicant functionality to accept a random
value in the Reserved field within EAPOL-Key frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is convenient for testing STA behavior with various RSN element
combinations and special cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The RSNXE generation function was extended to support this earlier, but
that update was missed from the RSNXOE variant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an explicit rsn_override_omit_rsnxe=1 configuration parameter to
allow the RSNXE to be omitted when using the RSNXOE and wanting to
minimize interoperability issues with STAs that might recognize the
RSNXE, but not handle it correctly, e.g., when multiple octets of
payload is included.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA command QCA_NL80211_VENDOR_SUBCMD_USD and related
attributes to support Unsynchronized Service Discovery (USD).
Device in active subscriber role sends SDF frames with service
information to find devices that advertise or publish the required
services. Device address, operation type, instance id, service_id,
channel info, service specific info, element container attribute, and
timeout are sent to the driver to initiate USD publish or USD subscribe
operation. The driver sends QCA_NL80211_VENDOR_SUBCMD_USD event with
instance_id and the USD operation status. QCA_NL80211_VENDOR_SUBCMD_USD
is also used to update publish operation and to cancel the publish or
subscribe operation for a service. It also allows all the operations to
be terminated using the USD flush command.
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Add support for RSNE/RSNXE Override elements. Use these elements to
determine AP's extended RSN parameters.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new capability flag based on the nl80211 feature advertisement for
RSN overriding support.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Allow hostapd to be configured to advertised two separate sets of
RSNE/RSNXE parameters so that RSNE/RSNXE can use a reduced set of
capabilities (e.g., WPA2-Personal only) for supporting deployed STAs
that have issues with transition modes while the new override elements
can use a newer security option (e.g., WPA3-Personal only) for STAs that
support the new mechanism.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.10 and v2.11. Update the copyright years for the main
programs.
Signed-off-by: Jouni Malinen <j@w1.fi>
In the hostapd_cleanup_driver() function, the NULL check for the driver
private data (drv_priv) is located within the CONFIG_IEEE80211BE feature
flag. As a result, on platforms where CONFIG_IEEE80211BE is not defined,
driver->hapd_deinit(drv_priv) is called with drv_priv set to NULL. This
leads to a null pointer exception in wpa_driver_nl80211_deinit().
To address this issue, move the NULL check for drv_priv outside the
CONFIG_IEEE80211BE build flag. This ensures that the check is performed
regardless of the value of CONFIG_IEEE80211BE, preventing the NULL
pointer exception.
Fixes: df34c2ced3 ("AP MLD: De-initialize/disable link BSS properly")
Signed-off-by: Sunil Ravi <sunilravi@google.com>
Currently wpa_ft_parse_ies() is setting FTE information to wpa_buf
pointer data which is generated after defragmentation. This data will
not contain FTE and Fragment element(s) headers.
IEEE P802.11be/D5.0 describes the MIC to be calculated on the
concatenation of FTE and corresponding Fragment element(s) which
implies the element headers are included for each element in the
fragmented case.
Fix this by correctly populating FTE information when FTE is
fragmented.
Fixes: 43b5f11d9 ("Defragmentation of FTE")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
During CSA with DFS channels, disable, enable interface is a part of the
algorithm. When interface was enabled old operating class before switch
and new channel were used causing mismatch in
configured_fixed_chan_to_freq() function.
Example of log when switch from channel 157 to 108 was triggered:
"Could not convert op_class 124 channel 108 to operating frequency"
Fixes: bb781c763 ("AP: Populate iface->freq before starting AP")
Signed-off-by: Marek Kwaczynski <marek@mazekey.pl>
When multi_ap is active, hostapd creates an AP-VLAN interface for 4addr
stations, even though wds_sta is not configured.
A check should be added to determine if wds_sta is active before
re-enabling the WDS mode by creating an AP-VLAN for 4addr stations.
Signed-off-by: Baligh Gasmi <gasmibal@gmail.com>
Going through five extra rounds of SAE commit messages in cases where
SAE peers are somehow unsynchronized feels unnecessary much to do by
default, so drop the default value to 3.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Reduce the number of unwanted SAE commit retries in synchronization
error cases when Sync > dot11RSNASAESync in mesh cases by discarding
received SAE commit messages for 10 seconds after a sync error has been
detected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
I've run into a case where I can bring a 2.4 GHz AP up without it being
in a bridge while I used the 'bridge=' config option. This happens when
the HT scan needed for 40 MHz operation failed to start from the get go
because another dev on the same phy was already in a scan. At the end
the AP is up and running but not added into any bridge.
Upon looking at the code, it seems that some hardware fails to issue a
scan while in AP and thus we have a fallback that switches the interface
from AP to STA before retrying another scan (it will change it back to
AP later on when finished). As we cannot have a (non-WDS) STA in a
bridge, during that procedure, we also remove/add the AP/STA from/to the
bridge as needed.
However, in wpa_driver_nl80211_scan() we do not set
drv->ap_scan_as_station until the end of the switch-to-sta &
retry-scan-start block. This means that when the recursive call to
wpa_driver_nl80211_scan() fails (the hardware is busy in my case) we
restore the interface to AP with wpa_driver_nl80211_set_mode() but that
will not add it back to the bridge. Problem.
To fix this lets always set drv->ap_scan_as_station before calling
wpa_driver_nl80211_set_mode(). In case wpa_driver_nl80211_set_mode() or
wpa_driver_nl80211_scan() fails lets call nl80211_restore_ap_mode() that
will set the mode back to AP but also handle the bridge thing as needed.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
The USD passive subscriber and solicited transmission only publisher
require receiving multicast NAN action frames in order to work.
Currently, we are not requesting to receive multicast when
registering NAN action frames. As a result, USD passive subscribe or
solicited only publish may not work.
The NL80211_ATTR_RECEIVE_MULTICAST attribute corresponds to wiphy
ext feature NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS, which
requires driver support and only a few drivers in the kernel tree
support it. Namely ath9k, ath9k_htc, ath10k and hwsim. We should
fall back to register non multicast action frames if the driver
has no support.
It was confirmed that ath9k_htc starts to work after the changes.
Note that even without requesting to receive multicast Action
frames, some drivers would still upload them. For example, rtl8192cu
and hwsim. This is why test cases like test_nan_usd_match would not
fail.
Tested-on: TP-LINK TL-WN821N v3(AR7010+AR9287, ath9k_htc)
Signed-off-by: Chien Wong <m@xv97.com>
The Wi-Fi Aware Specification v4.0 only defines unsolicited
transmissions only, solicited transmissions only and both unsolicited
and solicited transmissions publish. The other possibility is undefined
so we should reject it.
Signed-off-by: Chien Wong <m@xv97.com>
When the first link is deleted and there are still remaining links,
drv->ctx should be updated to the new default link on the bss.
Otherwise, drv->ctx points to the address that has already been freed
and makes hostapd crash.
Fixes: d2b62b3fe5 ("AP MLD: Support link removal before removing interface")
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Currently, when the ACS is updating the puncturing bitmap, the function
acs_update_puncturing_bitmap() sets the primary channel bitmap to 0.
This leads to a potential issue where the primary channel could be
punctured if ACS selects a different best channel within the same
segment.
To fix this issue, ensure that the primary channel bitmap is correctly
set by calculating the index of the primary channel based on the
frequency difference between the current channel and the best channel in
the segment, and is then passed to acs_update_puncturing_bitmap().
Fixes: af0f60e7dd ("EHT: Calculate puncturing bitmap for ACS")
Signed-off-by: Hari Naraayana Desikan Kannan <quic_hnaraaya@quicinc.com>
The current ACS algorithm incorrectly returns success even when there is
no survey list, leading to improper interference factor calculation.
This leads to treating 0 as a valid interference factor, which affects
channel selection judgment.
Fix the issue by ensuring success is only returned when the survey list
is not empty, thereby ignoring non-zero values in the interference
factor calculation.
Signed-off-by: Hari Naraayana Desikan Kannan <quic_hnaraaya@quicinc.com>
Update the documentation to reflect the ACS algorithm used in the code.
No functionality change.
Signed-off-by: Hari Naraayana Desikan Kannan <quic_hnaraaya@quicinc.com>
While TKIP should not really be used at all anymore and is not allowed
for WPA3 (which is required for Wi-Fi 7), there are some deployed APs
that allow WPA2 PSK to be used with MLO and even allowing WPA+WPA2 mode
with TKIP as the group cipher). IEEE P802.11be/D5.0 does not seem to
explicitly disallow this combination, so handle the MLO GTK KDE key
processing similarly to the way GTK KDE is processed, i.e., including
swapping of Michael MIC Tx and Rx keys for TKIP.
This fixes issues with Michael MIC failures if TKIP is used as a group
cipher for a multi-link association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new "ssid_verified=1" entry into the control interface STATUS
command output if the SSID has been verified for the current
association. This verification may have been done implicitly (e.g., with
SAE H2E and FT protocol binding in the SSID into key derivation or with
FILS protecting the SSID element in the (Re)Association Request frame)
or explicitly with the recently added SSID protection mechanism during
the 4-way handshake.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On the AP responder side, KDK was derived if the driver advertises
WPA_DRIVER_FLAGS2_SEC_LTF_AP. That is not correct, i.e., this needs to
also depend on the initiator indicating support for this in the RSNXE of
PASN authentication frame 1.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
The matching code currently only tests whether the prefix of a function
matches. Make this more strict by ensuring that the function name is not
longer.
However, as this breaks some tests (due to inlining), add the ability to
do an explicit prefix match by appending a '*' to the function name. Use
this to change the eap_eke_prf match to eap_eke_prf_* in order to match
one of the actual implementations.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The functions specified by the user might be longer than the function in
the backtrace, potentially overflowing the memcmp(). In practice, it
should not be a relevant out-of-memory read. However, we can use
strncmp() instead.
Note that, as before, this is only a prefix match. If a function name is
longer in the backtrace it will still match.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
If the kck_len is 0 then the pointer may be NULL. If that happens UBSAN
complains about the NULL pointer as memcpy() has the arguments declared
to never be NULL even if the copied number of bytes were zero.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Since 0ce1545dcb ("nl80211: Determine maximum number of supported
AKMs") we get the maximum number of supported AKMs from the kernel.
Let's use that instead of the legacy NL80211_MAX_NR_AKM_SUITES when
setting up AP mode operation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some deployed STAs that advertise SecureLTF support in the RSNXE in
(Re)Association Request frames, do not derive KDK during PTK generation.
Since the correct key calculations in the AP includes an additional KDK
generation in such cases, this causes different PTK-KCK being derived
and the AP ultimately discarding EAPOL-Key message 2/4 due to MIC
validation failure.
Try to derive a PTK without KDK as a workaround in such cases and allow
the 4-way handshake to continue if this results in a matching MIC.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
When an HE BSS color event is received from the driver, the event was
delevered to the first link BSS ctx. To support HE BSS color with MLO,
there is a need to identify the correct link for which the event is
intended.
Add link ID parsing support in the event handler and pass the link ID
(if included) down to the event handler so that appropriate link can be
selected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Almost same logic is there in handling four different commands related
to color collision. Later when link ID needs to be parsed, it would be
more duplicate logic at four different places. Hence refactor and bring
it in a single function.
No functionality changes.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
In function handle_assoc(), ieee802_11_update_beacons() was used to
update the Beacon frames. However, with commit a5d0bb42a2 ("Reduce
delay between Association Request and Association Response"), it was
changed to ieee802_11_set_beacons() which basically overturned what
commit e59d2a31cf ("hostapd: Fix premature beacon set during
association handling") did which is not correct.
Fix this and use ieee802_11_update_beacons() instead of
ieee802_11_set_beacons().
Fixes: a5d0bb42a2 ("Reduce delay between Association Request and Association Response")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
There is no need to depend on all uses (i.e., both hostapd and
wpa_supplicant) to verify that the length of the Rejected Groups field
in the Rejected Groups element is valid (i.e., a multiple of two octets)
since the common parser can reject the message when detecting this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The latest Linux kernel is mandating link ID with NL80211_CMD_TDLS_MGMT
for MLO connections. This resulted in not being able to perform TDLS
operations during a multi-link association.
Fix this by sending link ID in NL80211_CMD_TDLS_MGMT when available. If
link ID info is not available, send the link ID of the association link.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Always check the Message-Authenticator attribute in a received RADIUS
message if it is present. Previously, this would have been skipped if
the attribute was not required to be present.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd required Message-Authenticator attribute to be included in EAP
authentication cases, but that requirement was not in place for MAC ACL
cases. Start requiring Message-Authenticator attribute for MAC ACL by
default. Unlike the EAP case, this can still be disabled with
radius_require_message_authenticator=1 to maintain compatibility with
some RADIUS servers when used in a network where the connection to such
a server is secure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not allow the exception for missing Message-Authenticator in
Access-Reject without EAP-Message. While such exception is allowed in
RADIUS definition, there is no strong reason to maintain this since
Access-Reject is supposed to include EAP-Message and even if it doesn't,
discarding Access-Reject will result in the connection not completing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Even if this might not be strictly speaking necessary for mitigating
certain RADIUS protocol attacks, be consistent with the RADIUS server
behavior and move the Message-Authenticator attribute to be the first
attribute in the RADIUS DAS responses from hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
Even if this is not strictly speaking necessary for mitigating certain
RADIUS protocol attacks, be consistent with the RADIUS server behavior
and move the Message-Authenticator attribute to be the first attribute
in the message from RADIUS client in hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the Message-Authenticator attribute to be the first attribute in
the RADIUS messages. This mitigates certain MD5 attacks against
RADIUS/UDP.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a Message-Authenticator attribute was already added to a RADIUS
message, use that attribute instead of adding a new one when finishing
message building. This allows the Message-Authenticator attribute to be
placed as the first attribute in the message.
Signed-off-by: Jouni Malinen <j@w1.fi>
When parsing a SAE Commit message, the temporary peer_rejected_groups
parameter was left to its old value in cases where the new SAE Commit
message did not include the Rejected Groups element. This could result
in unexpected behavior if a previously processed SAE Commit message
included a Rejected Groups element that claimed one of the enabled
groups to be rejected.
Explicitly clear the peer_rejected_groups value when parsing an SAE
Commit message without a Rejected Groups element to avoid rejecting the
new message based on some previously received incorrect information.
This avoids some potential denial-of-service issues during the lifetime
of the SAE temporary data.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of practically ignoring an odd octet at the end of the element,
check for such invalid case explicitly. This is needed to avoid a
potential group downgrade attack.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a vendor attribute to configure a STA to follow AP advertised
preference values to select roam candidates with BTM.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the existing QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE
attribute for TWT setup request to configure the Responder PM Mode bit
in the control field of the TWT element or broadcast TWT schedule.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add a flag attribute
QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_UNAVAILABILITY_MODE into enum
qca_wlan_vendor_attr_twt_set_param to configure the TWT responder
unavailability outside of the SPs of its broadcast TWT schedule.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Authentication rejection was found when doing fuzz testing even with a
valid SAE commit message when it was sent after a SAE commit message
that included an incorrect password identifier. The test steps for this
are as below:
1. Peer sends an abnormal commit message with incorrect password
identifier
2. APUT rejects as expected
3. Peer sends a valid commit message
4. APUT rejects again, which is not expected
In step 2, as the abnormal data fakes an empty password identifier
element, it passes sae_is_password_id_elem() checking. Memory is then
allocated for sae->tmp->pw_id. The authentication process then fails
due to no available password with this invalid password identifier.
In step 4, though the peer sends a valid commit message, APUT rejects
this SAE commit again due to no password identifier element (due to that
sae->tmp->pw_id being set), which is not expected.
Free the sae->tmp->pw_id field and set it to NULL when SAE commit
message processing fails due to an unknown password identifier so that
the bogus value is not used as a requirement for any consecutive SAE
commit from the same STA before the STA entry gets cleared.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
The Link Id attribute is required for secure ranging context to identify
the link on which the command is received for an MLD.
Signed-off-by: Nidhi Jain <quic_nidhjain@quicinc.com>
The Link Id attribute is required for QCA_NL80211_VENDOR_SUBCMD_PASN to
identify the link on which the command is received for an MLD.
Signed-off-by: Nidhi Jain <quic_nidhjain@quicinc.com>
The Link Id attribute is required for external ACS context to identify
the link on which the command is received for an AP MLD.
Signed-off-by: Diya Sati <quic_dsati@quicinc.com>
Add support for SSID protection in 4-way handshake based on the
mechanism added in IEEE 802.11REVme/D6.0. This is a mitigation against
CVE-2023-52424 (a.k.a. the SSID Confusion Attack).
This functionality is disabled by default and can be enabled with
ssid_protection=1. Once there has been more testing of this to confirm
there is no significant interoperability issues, the goal is to be able
to change this to be enabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for SSID protection in 4-way handshake based on the
mechanism added in IEEE 802.11REVme/D6.0. This is a mitigation against
CVE-2023-52424 (a.k.a. the SSID Confusion Attack).
This functionality is disabled by default and can be enabled with
ssid_protection=1 in the network profile. Once there has been more
testing of this to confirm there is no significant interoperability
issues, the goal is to be able to change this to be enabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Send the link ID in the nl80211 command to switch color if the AP is
affiliated with an AP MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Once CCA is finished, Beacon frames need to be updated. The BCCA element
needs to be removed and the new color value shall be advertised in the
BSS Color Information field of the HE Operation element.
Update the Beacon frames accordingly.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add hostapd_cli command "color_change <color>" to change BSS color at
run time. hostapd_cli status can be used to check the updated color.
Usage: hostapd_cli -i <interface> color_change <color>
If 0 value is given, HE BSS color would be disabled. Same or a non-zero
value between [1-63] can be given to enable color again.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, if ACS scan request fails, states are cleared and returned.
However, in case of MLO, there is a possibilty of getting return value
of -EBUSY. In this case, ACS can retry the scan request after some time
similary to the HT40 scan.
Hence, retry the scan after 5 seconds if -EBUSY is returned. Maximum of
15 re-attempts are made before giving up.
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Co-developed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, RADIUS client, auth server, and 802.1X are copied from the
first link's BSS into the non-first link during its setup. However,
there could be a case where the first link is not initialized fully
because of ACS/HT40 SCAN/DFS. Hence, in such cases, NULL is getting
copied and later it leads to segmentation fault.
Initialize those on behalf of the first link in such case and update it
so that the next time other non-first link can use it.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Parse the Multiple BSSID element in Beacon frames and create and update
all the nontransmitted BSSs.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Userspace tools can use QCA_WLAN_VENDOR_ATTR_CONFIG_IF_OFFLOAD_TYPE to
configure the different below acceleration features (hardware, software)
on a per interface basis.
0 - No acceleration Packets are processed through the Linux kernel
networking stack.
1 - Software based acceleration: Packets are processed through the
shortcut forwarding engine (SFE) to bypass the Linux networking stack
for improved throughput performance. This option is applicable for AP,
STA, and Mesh mode and available for all radio designs. From the
performance aspect, this option consumes more CPU compared to the other
two options. Linux traffic control can be further applied with this
option to have more control on the traffic flows.
2 - Hybrid acceleration (software and hardware acceleration combined):
Packets are processed through both hardware and software in this case.
Packet classification is done by the hardware and then the packets are
delivered to software along with classification results as meta data.
Software can choose to do more classification/QoS based on use cases.
This is applicable for AP, STA, and Mesh modes and is available for all
radio designs. From the performance aspect, this option consumes
relatively less CPU compared to the SFE option above. Linux traffic
control rules cannot be applied with this option.
3 - Hardware based acceleration : Packets are processed through special
hardware (Direct Switch) rings which can directly forward the packets
between ethernet hardware and Wi-Fi hardware with very less software
involvement. This is applicable only for AP and STA modes; not
applicable for Mesh mode. From the performance aspect, this option
consumes very much less CPU compared to the other options. Linux traffic
control rules cannot be applied when this option is used. This option is
applicable only for specific radio designs. When this option is not
available, the default option (SFE) would be configured.
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Add following vendor attributes to dynamically configure parameters to
detect data stall for consecutive TX no ack.
- QCA_WLAN_VENDOR_ATTR_CONFIG_CONSECUTIVE_TX_NO_ACK_DURATION
- QCA_WLAN_VENDOR_ATTR_CONFIG_CONSECUTIVE_TX_NO_ACK_THRESHOLD
Signed-off-by: Jianmin Zhu <quic_jianminz@quicinc.com>
Add a new hostapd configuration parameter max_acceptable_idle_period to
allow the AP to accept per-STA requested BSS max idle periods.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow hostapd to be configured to not disconnect a STA if the STA fails
to reply to a group key handshake when BSS max idle period management is
used. This might be needed for some STAs that use aggressive power
saving (e.g., battery powered IoT devices).
This is disabled by default since this can delayed group rekeying
slightly and also to maintain the previous behavior. The more relaxed
operation can be enabled with the new configuration parameter
no_disconnect_on_group_keyerror=1.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
