This reverts commit 3204795d7a.
The commit adds an additional check that checks for overlapping BSSs in
addition to the existing 40 MHz intolerance subfield checks. The commit
cites IEEE Std 802.11-2016, 11.16.12, which defines the proper behavior
for a 20/40 MHz HT STA and AP, but the standard actually doesn't say
anything about overlapping BSSs. Specifically, the standard states that
the only BSSs that belong in the Intolerant channel report are those
that satisfy trigger event A, defined as channels with BSSs that don't
contain the HT capabilities element (which wpa_supplicant already did
before). Note that we also include channels with BSSs that have the 40
MHz intolerance bit set in the Intolerant channel report.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add support for PKEXv2 core protocol. This defines a new PKEX Exchange
Request message type with protocol negotiation and different rules for
key derivation with PKEXv2 or newer is used.
This does not change existing behavior for PKEX, i.e., the PKEXv1
variant will still be used by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the dpp_test parameter to be used to request the Protocol Version
attributed to be omitted from the Peer Discovery Request/Response
message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the Protocol Version attribute is used appropriate in Peer
Discovery Request/Response messages in cases where the signed Connector
includes the version information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate Peer Discovery Request/Response messages using the protected
version from the Connector, if present, instead of the currently
supported protocol version which might be higher than the one that got
included into the signed Connector during provisioning earlier.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
CONFIG_DPP3=y can now be used to configure hostapd and wpa_supplicant
builds to include DPP version 3 functionality. This functionality is
still under design and the implementation is experimental and not
suitable to be enabled in production uses before the specification has
been finalized.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Align the process logic for ap_vendor_elements and ap_assocresp_elements
parsing by using the wpabuf_parse_bin() helper function in both.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
wpa_add_scan_freqs_list() was updated to use bool for the is_6ghz
argument, but these callers were missed when updating the values from
0/1 to false/true.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channels included for the scan to connect to a P2P GO are optimized
such that the P2P GO preferred channel and the common channels are
included for the first few scans followed by a full scan in which all
the channels supported by the local device are included. This results in
P2P client including the 6 GHz channels for the full scan after GO
Negotiation even when 6 GHz channels are not used for the P2P
connection.
Exclude the 6 GHz channels from the full scan if 6 GHz channels are
supported but are not used for P2P connection.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
update proto type, AKMP suite, and pairwise cipher suite based on the
(Re)Association Request frame. Update PMF, group cipher, and group mgmt
cipher based on the AP's RSNE into wpa_sm. group_mgmt_cipher needs to be
updated based on PMF capabilities of STA and roamed AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since the 6 GHz band has no DFS channels, enable 6 GHz 160 MHz bandwidth
as the default configuration for IEEE 802.11s mesh.
example:
network={
ssid="6gmesh160"
key_mgmt=SAE
mode=5
frequency=6275
psk="1234567890"
}
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
IEEE Std 802.11ax-2021 mandates 6 GHz STA to use Management Frame
Protection (MFP) when RSN is enabled.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Channel numbers of the 6 GHz band overlap those of the 2.4 GHz and 5 GHz
bands. Thus converting to frequency based mesh channel selection helps
accommodate 6 GHz mesh.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
AKMP and proto were not updated in wpa_sm. Hence, update AKMP and proto
used with roamed AP when association event received from the driver in
SME offloaded to the driver scenario to avoid incorrect AKMP details in
wpa_supplicant similarly to how the cipher suite updates were added in
commit 2b3e64a0fb ("Update ciphers to address GTK renewal failures
while roaming") .
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Wi-Fi Display functionality needs P2P to be enabled. Ignore
CONFIG_WIFI_DISPLAY if CONFIG_P2P is not enabled for the build. This
avoids following compilation issue with invalid build configuration:
../src/ap/ap_drv_ops.c: In function 'hostapd_build_ap_extra_ies':
../src/ap/ap_drv_ops.c:163:10: error: 'struct hostapd_data' has no member named 'p2p_group'
163 | if (hapd->p2p_group) {
| ^~
../src/ap/ap_drv_ops.c:165:35: error: 'struct hostapd_data' has no member named 'p2p_group'
165 | a = p2p_group_assoc_resp_ie(hapd->p2p_group, P2P_SC_SUCCESS);
| ^~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit b0f457b619 ("SAE: Do not expire the current PMKSA cache entry")
depends on sm->cur_pmksa to determine if it is the current PMKSA cache
entry, but sm->cur_pmksa was not always correct for SAE in the current
implementation.
Set sm->cur_pmksa in wpa_sm_set_pmk() (which is used with SAE), and skip
clearing of sm->cur_pmksa for SAE in wpa_find_assoc_pmkid(). This latter
case was added by commit c2080e8657 ("Clear current PMKSA cache
selection on association/roam") for driver-based roaming indication and
Suite B, so skipping it for SAE should be fine.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using pkg-config for libpcsclite can provide more accurate linking
flags.
Signed-off-by: Reinhard Tartler <siretart@tauware.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Make sure that D-Bus isn't shut down before wpa_supplicant, as that would
also bring down wireless links which are still holding open NFS shares.
Debian bug: https://bugs.debian.org/785579
systemd upstream bug: https://bugs.freedesktop.org/show_bug.cgi?id=89847
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Every usage of these variables appends an extra slash, so keeping
a slash in the default values leads to double slashes in resulting
paths.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Some distros carry patches to specify driver fallback, but only in
specific conditions (e.g. the systemd service definition[1]). This leaves
other wpa_supplicant instances needing to define fallback themselves,
which leads to places where wpa_supplicant thinks it can't find a
driver[2]. Instead, when -D is not specified, have wpa_supplicant try
all the drivers it was built with in an attempt to find a working one
instead of just giving up if the first doesn't work.
[1] https://salsa.debian.org/debian/wpa/-/blob/debian/unstable/debian/patches/networkd-driver-fallback.patch
[2] https://bugs.launchpad.net/netplan/+bug/1814012
Signed-off-by: Kees Cook <kees@ubuntu.com>
Update PMKSA cache when interface is disabled and then enabled based on
the new MAC address. If the new MAC address is same as the previous MAC
address, the PMKSA cache entries are valid and hence update the PMKSA
cache entries to the driver. If the new MAC address is not same as the
previous MAC address, the PMKSA cache entries will not be valid anymore
and hence delete the PMKSA cache entries.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
While creating a cloned PMKSA entry for OKC both expiration and
reauth_time values are set to maximum values, but later only the
expiration time is copied from the old PMKSA entry to the new PMKSA
entry. Due to this there is a possibility of reauth_time becoming
greater than expiration time in some cloned entries. To avoid this copy
reauth_time also to the cloned entry.
Also, add check to reject control interface commands with reauth time
greater than expiration time.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Replaced the word "sanity" with the inclusive word "validity". The
comment in acs_survey_interference_factor() was referring a function
that does not exist, so remove it instead of trying rename the function.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Allow sae_pwe parameter to be configured per-network and enforce the
SAE hash-to-element mechanism for the P2P GO if it is started on
a 6 GHz channel.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming from WPA2-AP (group=CCMP) to WPA-AP (group=TKIP) using
driver-based SME and roaming trigger, GTK renewal failures are observed
for the currently associated WPA-AP because of group cipher mismatch,
resulting in deauthentication with the AP.
Update the group cipher and pairwise cipher values in wpa_sm from
association event received from the driver in case of SME offload to the
driver to address GTK renewal failures (and similar issues) that could
happen when the driver/firmware roams between APs with different
security profiles.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an explicit check for modes != NULL instead of depending on
num_modes > 0 implying that. This is to silence invalid static analyzer
reports.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support adding/deleting vendor elements dynamically for AP mode while it
is started by wpa_supplicant instead of hostapd which already supported
this. This adds ap_assocresp_elements global parameter and UPDATE_BEACON
control interface command to take the changed values into effect.
Usage in wpa_cli:
Add vendor IE for (Re)Association Response frames
> set ap_assocresp_elements=xxxx
Add vendor IE for Beacon/Probe Response frames
> set ap_vendor_elements=xxxx
Delete vendor IE from (Re)Association Response frames
> set ap_assocresp_elements
Delete vendor IE from Beacon/Probe Response frames
> set ap_vendor_elements
To make vendor IE changes take effect
> update_beacon
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Add support to send DSCP Policy Query frame using a new control
interface command DSCP_QUERY. This includes support for a wildcard DSCP
query and a DSCP query with a single Domain Name attribute.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse WFA Capabilities element from the (Re)Association
Response frame. Also register a timeout for the station to wait before
sending a new DSCP query if requested by AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Indicate DSCP Policy capability by including a WFA Capabilities element
containing the relevant bit set to 1 in the (Re)Association Request
frames when enabled by user.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to prepare and send DSCP response action frame to the
connected AP in response to a new control interface command DSCP_RESP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse received DSCP Policy Request frames and send the
request details as control interface events.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The DSCP policy capability is disabled by default. The user frameworks
which have support for handling DSCP policy request messages need to
enable this capability explicitly to allow wpa_supplicant to advertise
the capability to the AP and allow the related frames to be processed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This function is not specific to GAS, so make it available throughout
wpa_supplicant without requiring CONFIG_GAS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.
For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'
- Previous behavior: AP fallback to channel 100 using 20 MHz with
"No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
"VHT center channel 106 for 80 or 80+80 MHz bandwidth"
This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enable support for P2P connection in 6 GHz with the channel width of 40
MHz, 80 MHz, and 160 MHz. The flag max_oper_chwidth is used to configure
the maximum channel width for P2P connection in 6 GHz with the commands
P2P_CONNECT, P2P_INVITE, and P2P_GROUP_ADD.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Current definition of wpas_p2p_get_ht40_mode() determines secondary
offset in the 5 GHz band. Enhance the functionality of this function to
determine offset to support 6 GHz channels also.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Clone pmf and p2p_6ghz_disable configuration values when creating a new
P2P group interface. PMF is required in 6 GHz band operation.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Currently while selecting a preferred frequency when no preference is
known, p2p_no_go_freq is not considered for 5 GHz and 60 GHz channels.
This results in starting GO on the channels that are configured not to
allow the local device as GO.
Use wpas_p2p_supported_freq_go api to check if the p2p_no_go_freq
configuration before selecting the preferred frequency for GO.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
For some 6 GHz operating class like 134, there is a possibility where
the ch variable used for channel iterator overflows when it is
incremented. Fix this by updating the datatype of ch variable to
avoid integer overflow while incrementing.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Generate an event on the control socket interface when a network is
added or removed. The event name CTRL-EVENT-NETWORK-<ADDED|REMOVED>
is followed by the network entry identifier. The event matches the
corresponding Network<Added|Removed> signal on the d-bus interface.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
The --conf option specifies a file containing a list of options
to configure the network used for running the test which will be
used in place of the defaults built into the script.
Signed-off-by: Nick Porter <nick@portercomputing.co.uk>
"SET disable_mscs_support 1" can be used to disable indication of MSCS
support in the Extended Capabilities element for testing purposes. This
is also disabling addition of the MSCS element even if valid
configuration parameters had been configured.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
"SET disable_scs_support 1" can be used to disable indication of SCS
support in the Extended Capabilities element for testing purposes.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to parse SCS control interface command and form the SCS
Request frame to be sent to SCS enabled AP.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Enable (and require) the management frame protection for the P2P GO if
it is started on a 6 GHz channel.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
P2P connections in the 6 GHz band use SAE authentication algorithm after
getting credentials with WPS connection. During WPS connection as it
doesn't use SAE, SAE PT is not derived. After getting SAE credentials,
the STA connects to the same SSID using SAE auth algorithm. Earlier, SAE
H2E PT was not derived while connecting to the same SSID to which the
STA is connected last time. Due to this, the P2P group formation fails
for 6 GHz channels when H2E is enabled as the PT will not be setup by
the P2P client before proceeding to the SAE authentication. Same could
happen with infrastructure WPS when wps_cred_add_sae=1 is used.
Set up the SAE H2E PT while connecting to the same SSID again also to
make sure that the H2E PT is set up in the STA to derive the PWE for
successful SAE authentication. The PT derivation will be skipped in
wpa_s_setup_sae_pt() if PT is already available for that SSID.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Though both 5 GHz channels and 6 GHz channels report the mode as
HOSTAPD_MODE_IEEE80211A, there is a possibility of different HT/VHT/HE
capabilities being available between these bands. Use get_mode() to
obtain correct capabilities to cover cases where the driver reports
different capability values for the 5 GHz and 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Determine if the TDLS peer supports TDLS in 6 GHz band based on the HE 6
GHz Band Capabilities element received in the TDLS Setup Response frame.
Indicate the peer's HE 6 GHz capabilities to the driver through
sta_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
External applications can store PMKSA entries persistently and
reconfigure them to wpa_supplicant after restart. This can result in
wpa_supplicant having a PMKSA for FILS authentication without having
matching ERP keys for it which would prevent the previously added
mechanism for dropping FILS PMKSA entries to recover from rejected
association attempts.
Fix this by clearing PMKSA entries configured by external applications
upon FILS connection failure even when ERP keys are not available.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
wpa_supplicant generates both a PMKSA cache entry and ERP keys upon
successful FILS connection and uses FILS authentication algorithm for
subsequent connections when either ERP keys or a PMKSA cache entry is
available.
In some cases, like AP/RADIUS server restart, both ERP keys and PMKSA
becomes invalid. But currently when an AP rejects an association,
wpa_supplicant marks only ERP keys as failed but not clearing PMKSA.
Since PMKSA is not cleared, consecutive connection attempts are still
happening with FILS authentication algorithm and connection attempts are
failing with the same association rejection again instead of trying to
recover from the state mismatch by deriving a new ERP key hierarchy.
Clear PMKSA entries as well on association rejection from an AP to allow
the following connection attempt to go with open authentication to
re-establish a valid ERP key hierarchy. Also, since clearing PMKSA
entries on unprotected (Re)Association Response frames could allow DoS
attack (reduce usability of PMKSA caching), clear PMKSA entries only
when ERP keys exists.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
CTRL-EVENT-AUTH-REJECT reporting was previously skipped when going
through SAE-specific Authentication frame handling. Add this event here
as well to be more consistent with control interface events.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use WPA3-Personal (SAE+PMF) for P2P connections in the 6 GHz band to
enable the Wi-Fi Display use case on the 6 GHz band without having to
use WPA2-Personal (PSK) on that new band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, 6 GHz channels were disabled for P2P operations. Use the new
allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD, and P2P_INVITE
commands for P2P connection on the 6 GHz channels when Wi-Fi Display is
enabled on both the devices.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher precedence.
Indicate P2P 6 GHz band capable information in Device Capability Bitmap
of P2P Capability attribute to indicate the P2P Device is capable of P2P
operation in the 6 GHz band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Introduce a new allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD,
and P2P_INVITE commands for P2P connection on the 6 GHz channels when
Wi-Fi Display is enabled on both the devices. This commit is only adding
the interface change without changing any actual P2P functionality.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, the 6 GHz channels were disabled for P2P operations.
Introduce a new include_6ghz parameter for the P2P_FIND command to
configure P2P discovery on the 6 GHz channels.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher priority. If the p2p_6ghz_disable parameter is not set in the
configuration, include_6ghz parameter can be used to enable or disable
the discovery operation in the 6 GHz channels for the P2P_FIND command.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Extend the previously 5 GHz specific 80 and 160 MHz channels helper
functions to support 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Do not skip scan results with zero length SSID (i.e., a hidden SSID)
when searching for potential BSS transition candidates since such
entries might be for the same ESS (i.e., for the current SSID). Use only
the BSSID check for such cases.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This helper function returns enum chan_allowed values, so use it as the
return type instead of unnecessarily generic int.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is safer to remove and free these entries with a shared helper
function to avoid issues with potentially forgetting to unregister or
free something if this structure is extended in the future.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a STA makes an association request that is rejected by an OCE AP
due to the RSSI being insufficient, the AP is added to the driver
disallow list by wpa_set_driver_tmp_disallow_list().
Once the AP increases TX power which makes the AP RSSI higher than
Association Rejection RSSI threshold, the AP is supposed to be removed
from the driver disallow list but that was not the case.
wpa_is_bss_tmp_disallowed() is called in the scan result handler, so it
is the best place to put the logic of removing the AP from the driver
disallow list with sufficient AP RSSI.
This is needed with drivers that use the temporarily disallowed BSS list
(which is currently supported only with a QCA vendor command). The
wpa_supplicant internal functionality was already taking care of this
with the wpa_is_bss_tmp_disallowed() return value even for cases where
the entry remaining in the list.
Signed-off-by: Hu Wang <huw@codeaurora.org>
APs in 6 GHz operating with LPI/VLP rules will have significantly lower
SNR values compared to 2.4/5 GHz band APs. Earlier, the estimated
throughputs were used for comparison only when the delta of SNRs between
both the APs was not greater than 7 and as a result for comparing 6 GHz
APs with 2.4/5 GHz APs, estimated throughputs were not getting used.
The estimated throughput calculations takes SNR value also into
consideration, hence remove RSSI delta check if any of the APs are from
the 6 GHz band. This change is limited to the 6 GHz band only in order
to avoid possible regressions with 2.4/5 GHz APs.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
This makes it convenient for an external test script to use
ext_eapol_frame_io=1 to delay and/or modify transmission of EAPOL-Key
msg 1/4 without having to use separate frame injection mechanisms.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Prefer 6 GHz APs when estimated throughputs are equal with APs from the
2.4/5 GHz bands while selecting APs for connection. Also add a 6 GHz
specific noise floor default value for the 6 GHz band (with the same
value as was used for 5 GHz previously) to make this step clearer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to consider HE rates while estimating throughputs for the
scan results from HE enabled APs. HE 0.8 usec GI rates are used in all
tables. The minimum SNR values for HE rates (1024-QAM) are derived by
adding the existing minimum SNR values of 256-QAM rates from VHT tables
and the difference between the values of minimum sensitivity levels of
256-QAM rates and 1024-QAM rates defined in Table 27-51 (Receiver
minimum input level sensitivity) in IEEE P802.11ax/D8.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to calculate estimated throughputs for APs which support the
160 MHz (including 80+80 MHz) mode in VHT. The minimum SNR values for
VHT 160 MHz mode are derived from minimum SNR values used for VHT 80 MHz
mode + 3 dBm. The min-SNR values are derived relatively based on the
information that the minimum sensitivity levels defined in Table 21-25
(Receiver minimum input level sensitivity) in IEEE Std 802.11-2020 for
the 160 MHz mode are higher by 3 dBm compared to the values of the 80
MHz mode for each rate.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add checks for features supported by the specific hardware mode of the
local device that has the channel for which the throughput is being
estimated instead of assuming the local device supports all optional
features. This is more accurate for cases where the local capabilities
might differ based on the band. In addition, this is in preparation for
extending rate estimates to cover optional VHT and HE features.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When the driver provides a list of supported modes, chan6 ended getting
added even if the 2.4 GHz mode was not included. This resulted in
incorrect behavior of trying to transmit on a not supported channel in
case of 5 GHz only radios.
Fix this by adding the channel 6 by default only if the driver does not
provide a list of supported modes. Whenever the supported modes are
available, only add this channel if it is explicitly listed as an
enabled channel.
Fixes: 8e5739c3ac ("DPP2: Check channel 6 validity before adding it to chirp channel list")
Signed-off-by: Kani M <kanisumi@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Commit 3ab35a6603 ("Extend EAPOL frames processing workaround for
roaming cases") added a work around to address the issue of EAPOL frame
reception after reassociation replied to with an incorrect destination
address (the BSSID of the old AP). This is due to association events and
EAPOL RX events being reordered for the roaming cases with drivers that
perform BSS selection internally.
This mechanism relies on the fact that the driver always forwards the
EAPOL handshake to wpa_supplicant after the roaming (sets
last_eapol_matches_bssid during the EAPOL processing and resets on the
assoc/reassoc indication).
The above approach does not address the case where the driver does the
EAPOL handshake on the roam, indicating the authorized status to
wpa_supplicant but also forwards the EAPOL handshake to wpa_supplicant
for few other roam attempts. This is because the flag
last_eapol_matches_bssid is not set with the roam+authorized event from
the driver. Thus, the next reorder of roam and EAPOL RX events would
miss this workaround.
Address this by setting last_eapol_matches_bssid=1 on a roam+authorized
event from the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant_ctrl_iface_deinit() was executed only if the
per-interface control interface initialization had been completed. This
is not the case if driver initialization fails and that could result in
leaving behind references to the freed wpa_s instance in a corner case
where control interface messages ended up getting queued.
Fix this by calling wpa_supplicant_ctrl_iface_deinit() in all cases to
cancel the potential eloop timeout for wpas_ctrl_msg_queue_timeout with
the reference to the wpa_s pointer. In addition, flush any pending
message from the global queue for this interface since such a message
cannot be of use after this and there is no need to leave them in the
queue until the global control interface gets deinitialized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a 2 octet field, so need to use WPA_GET_LE16() here instead of
using only the first octet of the value.
Fixes: bbd3178af4 ("MSCS: Add support to process MSCS Response frames")
Signed-off-by: Jouni Malinen <j@w1.fi>
Process the received comeback cookie and retry automatically if the AP
allows this. Otherwise, provide the cookie to upper layers to allow a
later attempt with the cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The new wpa_supplicant control interface command "PASN_DEAUTH
bssid=<BSSID>" can now be used to flush the local PTKSA cache for the
specified BSS and to notify the AP to request it to drop its PTKSA as
well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
An EAPOL frame may be pending when wpa_supplicant requests to
deauthenticate. At this stage the EAP SM cache is already cleaned by
calling eapol_sm_invalidate_cached_session(). Since at this stage the
wpa_supplicant's state is still set to associated, the EAPOL frame is
processed and results in a crash due to NULL dereference.
This wasn't seen previously as nl80211 wouldn't process the
NL80211_CMD_CONTROL_PORT_FRAME, since wpa_driver_nl80211_mlme() would
set the valid_handler to NULL. This behavior was changed in commit
ab89291928 exposing this race.
Fix it by ignoring EAPOL frames while the deauthentication is in
progress.
Fixes: ab89291928 ("nl80211: Use process_bss_event() for the nl_connect handler")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the address family when manually constructing IPv4 addresses in
eapol_test on Windows. Otherwise other functions, like hostapd_ip_txt()
in src/utils/ip_addr.c, that rely on addr->af being set fail miserably.
The non-Windows option uses hostapd_parse_ip_addr() which does this as
part of the helper function.
Signed-off-by: Stefan Paetow <oss@eons.net>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
