When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:
1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
DGAF disabled bit is zero
Clear the filter configuration when the station interface is
disassociated.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.
Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
According to IEEE Std 802.11-2012, Table 8-22, vendor specific elements
must follow all other elements, so Hotspot 2.0 element which is actually
a vendor specific element must come after all other elements.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
According to IEEE Std 802.11-2012, Table 8-22, RM Enabled Capabilities
element must come before the Extended Capabilities element.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Connect radio work is sometimes delayed for a considerable duration if
there is an ongoing scan radio work. To avoid these delays abort the
ongoing scan on that interface before queuing a connect request. Upon a
scan done indication from the driver, connect radio work will be
scheduled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.
Signed-off-by: Jouni Malinen <j@w1.fi>
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The sae_groups parameter is zero terminated array, not -1 terminated, so
must check the value against <= 0 to break out from the loop.
Signed-off-by: Jouni Malinen <j@w1.fi>
Call the FT processing function directly instead of going through
wpa_supplicant_event() to process FT Authentication frame in SME case.
This allows parsing error to be used to trigger immediate failure for
the connection instead of trying to proceed to reassociation step that
cannot succeed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ft_sae test case managed to hit a somewhat unclear error case which
resulted in "WPA: Failed to select WPA/RSN" print and not enough
information to figure out what exactly had went wrong.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of just stopping connection process and network discovery,
report SAE failures to build Authentication frames (e.g., due to missing
password) as a connection failure to get the normal retry mechanism into
use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).
Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
While the buffer is expected to be large enough for all the IEs, it is
better to check for this explicitly when adding the HS 2.0 Indication
element. (CID 68601)
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.
Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.
In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a new connection is attempted while there is a pending sme-connection
radio work, cancel the pending radio work and continue with the new
connection attempt. This is preferable over rejecting the new work and
continuing with the pending one, as it is possible that the previous
work is no longer valid.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug wpa_supplicant behavior when reporting
20/40 MHz co-ex information based on OBSS scans.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 40 MHz intolerant bit needs to be checked before skipping the BSS
based on the channel already being in the lost (which could have
happened due to another BSS that does not indicate 40 MHz intolerant).
This fixed the 20/40 MHz co-ex report to indicate 20 MHz request
properly if there are both 40 MHz tolerant and intolerant BSSes on the
same channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Commit 6ac4b15ef8 (wpa_radio work for
connection) caused a regression for cases where multiple auth_alg values
are set in a network block and wpa_supplicant-based SME is supposed to
iterate through them. The connection radio work was not terminated when
receiving authentication failure and this resulted in the following
authentication attempt failing.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
