Add a simple test that exemplifies TX power configuration when operating
on the 6 GHz band.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some of these can take close to the previously used timeouts and this
could result in reporting failures in cases that worked fine.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test EHT connection on the 5 GHz band with channel bandwidths 20-160 MHz
and up to 320 MHz on the 6 GHz band.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This avoids issues with old scan results from a previous test causing
incorrect association after WPS exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previous timeout allowed only a single chirping round, and sometimes
not even that full round. That resulted in test failures for cases where
there was not really any incorrect behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Stop dev[0] from trying to associate at the end of the test case to
reduce risk for leaving out some pending operations that could mess up
the following test case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Handle the cases where the first attempt to start scan fails due to an
ongoing scan. Stop such scan and try again instead of failing the test
case immediately.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This avoids race conditions with UML time-travel where some cases ended
up not reporting the DPP-TX-STATUS event and that resulted in discarding
events that are more important to verify for correct behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
One of the sigma_dut testing cases missed the t.join() call to make
surte the separate thread terminated. This could result in confusing
"unexpected stdout output" in a middle of an unrelated test case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Stop and restart P2P_FIND on dev[1] to avoid timing issues where the
wait on dev[1] makes the test case fail even though this was trying to
verify that dev[0] is reacting quickly enough.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait a bit between the DPP-SCAN-PEER-QR-CODE event and reporting of the
QR Code to avoid a race condition.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Avoid a race condition that could result in the relay (hostapd)
maintaining STA association with PMF and discarding of the GAS frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Terminate the group explicitly before cleanup to avoid a race condition
between an automatically started scan to find the GO again and the scan
started to clear the scan cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait a bit to allow stopping of the DPP_LISTEN operation to be completed
before issuing the DPP_QR_CODE command that would send the frame that
these test cases expect to not get ACKed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait some time between the first DPP Authentication Response that
indicates the response is not yet available and the second DPP
Authentication Response to make this sequence a bit more realistic and
less likely to hit race conditions with UML time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for hostapd to complete STA authorization before running the
connectivity test between two associated STAs.
Signed-off-by: Jouni Malinen <j@w1.fi>
It can take significant amount of time to find the peer in this type of
a case where an AP connection is forced on a different channel while
going through p2p_find on both devices.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
DPP initiator will try three channels in this sequence and it can take
very close to the previously used five second timeout before being able
to try on the actual operating channel of the AP. This could result in
the test case failing unnecessarily. Increase the timeout to avoid this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Avoid potential race condition in ap_cipher_tkip_countermeasures_ap by
sending the first test frame only after the AP has completed processing
the 4-way handshake and also wait a bit to allow the group key handshake
to be completed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If a tests hits a WARN_ON_ONCE then the retriggering will make it appear
to pass, since the warning will not happen again. Make this more
reliable by resetting the states at the beginning of each test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The kernel has an asynchronous work to enable TX, which hasn't always
run by the time we get to TX tests. Do a sysfs read from the carrier
file before TX, on newer kernels this synchronises the needed state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It looks like the lifetime_in_memory test cases can hit a read failure
(Errno 5 - Input/output error) every now and then, so skip memory areas
that report that, but go through all readable process memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for AP/GO to complete processing before taking the next step in a
test instead of waiting just for STA. This avoids race conditions with
UML time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remaining lifetime of the PMKSA entry is decreasing, so need to
allow it to differ between the old and new entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
