Make struct wpas_pasn common for both the initiator and the responder by
adding required parameters for responder to the existing struct
wpas_pasn. This makes both hostapd and wpa_supplicant share the same
structure definitions in preparation for allowing PASN functionality to
be built into a separate library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide enough information to allow the FTE to be built using the
correct MIC field length based on the used AKM and key length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
bss->conf->bssid may be kept unset and will cause an empty BSSID field
in RNR. Fix this to use own_addr instead.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Signed-off-by: moran.daori <moran.daori@celeno.com>
AP as a responder, on successful completion of PASN authentication
configures the required keys by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_validate_wpa_ie() might update sm->* values, so it should not be
allowed for an existing STA entry if that STA has negotiated MFP to be
used for the association. Fix this by first checking whether an SA Query
procedure needs to be initiated. In particular, this prevents a
potential bypass of the disconnection protection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for EHT capabilities in the addition of a new station entry
to the driver.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Parse EHT capabilities sent by a non-AP STA in (Re)Association Request
frames. Validate the length of the element, matching MCS rates between
AP TX and STA RX. Store the capabilities in the station info structure.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add EHT Operation element in Beacon, Probe Response, and (Re)Association
Response frames using the format described in IEEE P802.11be/D1.5,
9.4.2.311.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
This information element is similar to the CSA one. It contains a
counter and the target color. Once the counter expired, the change to
the new color happens.
Just note the current implementation is based on CCA counter attributes
that only take Beacon and Probe Response framesinto account.
(Re)Association Response frames do not currently have kernel APIs to
decrement the CCA counter since mediatek mcu firmware does not support
it yet and it will be added in future firmware release.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Add Transmit Power Envelope element for 6 GHz per IEEE Std
802.11ax-2021.
Currently, this uses hard coded EIRP/PSD limits which are applicable to
6 GHz operation in United states, Japan, and Korea. Support to extract
power limits from kernel data will be added after complete regulatory
support is added for the 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
force_kdk_derivation is defined within CONFIG_TESTING_OPTIONS, so need
to use matching condition when accessing it.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a workaround for mac80211 behavior of retransmitting the
Association Request frames multiple times if the link layer retries
(i.e., seq# remains same) fail. The mac80211 initiated retransmission
will use a different seq# and as such, will go through duplicate
detection. If we were to change our DH key for that attempt, there would
be two different DH shared secrets and the STA would likely select the
wrong one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add an alternative sequence for performing the RADIUS ACL check and PSK
fetch. The previously used (macaddr_acl=2, wpa_psk_radius=2) combination
does this during IEEE 802.11 Authentication frame exchange while the new
option (wpa_psk_radius=3) does this during the 4-way handshake. This
allows some more information to be provided to the RADIUS authentication
server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only the SME-in-hostapd case updated sta->ext_capability while the
SME-in-the-driver case updated sta->qos_map_enabled, but not other items
related to the extended capabilities. This resulted in reduced
information being available through the control interface.
Use the shared helper function for both cases to get matching
information available regardless of the SME architecture.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Allow the first Tunnel-Password RADIUS entry to be used for SAE in
addition to the sae_password entries and wpa_passphrase parameters from
the static configuration file.
Signed-off-by: Mario Hros <git@reversity.org>
Report TX status for DPP messages even if the destination address was
broadcast. This is needed to get appropriate trigger for PKEX retries.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The rx_freq of Public Action frame was not maintained by the GO and the
GO always sent the response on the operating channel. This causes
provision discovery failure when a P2P Device is sending a PD Request on
a 2.4 GHz social channel and the GO is responding on a 5 GHz operating
channel.
Save the rx_freq and use it for GO to sent the response. This extends
commit c5cc7a59ac ("Report offchannel RX frame frequency to hostapd")
to cover additional frame types.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Include Reduced Neighbor Report element in Beacon and Probe Response
frames by default if the reporting AP is 2.4/5 GHz and it is co-located
with a 6 GHz AP. Similarly, include RNR by default in FILS Discovery
frames if the AP is a standalone 6 GHz AP.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Calculate the length and include data for the BSSes active on the same
radio as the reporting BSS in the Reduced Neighbor Report element. This
element is included in Beacon and Probe Response frames.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Include data from the existing neighbor database in the Reduced Neighbor
Report element in Beacon frames if the configuration option 'rnr' is
enabled for the BSS.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_sae_commit’:
../src/ap/ieee802_11.c:2401:60: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: SAE buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_sae_confirm’:
../src/ap/ieee802_11.c:2477:60: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: SAE buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_fils’:
../src/ap/ieee802_11.c:2707:62: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: FILS: Buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
IEEE Std 802.11-2016, 12.4.7.6 specifies:
An SAE Commit message with a status code not equal to SUCCESS shall
indicate that a peer rejects a previously sent SAE Commit message.
An SAE Confirm message, with a status code not equal to SUCCESS, shall
indicate that a peer rejects a previously sent SAE Confirm message.
Thus when SAE authentication failure happens, authentication transaction
sequence number should not be incremented.
Signed-off-by: Jia Ding <jiad@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reuse the SAE anti-clogging token implementation to support similar
design with the PASN comeback cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a Deauthentication frame is received, clear the corresponding PTKSA
cache entry for the given station, to invalidate previous PTK
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The anti-clogging code was under CONFIG_SAE. Change this so it can be
used both with CONFIG_SAE and CONFIG_PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication mandates support for comeback flow, which
among others can be used for anti-clogging purposes.
As the SAE support for anti clogging can also be used for PASN,
start modifying the source code so the anti clogging support
can be used for both SAE and PASN.
As a start, rename some variables/functions etc. so that they would not
be SAE specific. The configuration variable is also renamed, but the old
version remains available for backwards compatibility.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As defined in IEEE P802.11az/D3.0, 12.12.3.2 for the second PASN frame.
This was previously covered only for the case when the explicit PMKSA
was provided to the helper function. Extend that to cover the PMKID from
SAE/FILS authentication cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
There is no point in trying to build in rest of this function if in the
middle of it the CONFIG_NO_RADIUS case would unconditionally fail.
Simply make all of this be conditional on that build parameter not being
set to make things easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reordering of code in handle_auth_cb() when adding support for full
station state messaged up frame length checks. The length was originally
tested before looking at the payload of the frame and that is obviously
the correct location for that check. The location after those full state
state changes was after having read six octets of the payload which did
not help at all since there was no addition accesses to the payload
after that check.
Move the payload length check to appropriate place to get this extra
level of protection behaving in the expected manner. Since this is a TX
status callback handler, the frame payload is from a locally generated
Authentication frame and as such, it will be long enough to include
these fields in production use cases. Anyway, better keep this check in
working condition.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd_get_oper_chwidth(iconf) instead of direct access to
iface->conf->vht_oper_chwidth is needed here to be able to use this with
HE in cases where VHT is not enabled.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
The new status code values for SAE H2E and PK resulted in the
sta->added_unassoc cases incorrectly removing the STA entry after
successful SAE commit messages. Fix this by using sae_status_success()
instead of direct check for WLAN_STATUS_SUCCESS when processing SAE
commit messages before removing station entry.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Note that the implementation is not complete as it is missing support
for the FT wrapped data which is optional for the station, but must be
supported by the AP in case the station included it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
Authenticator state machine.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Make sae_status_success() more explicit by rejecting SAE-PK status code
when the AP is not configured with PK.
Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When testing SAE reflection, the incoming commit may have the H2E status
code (126) or SAE-PK (127), but the test code in the AP was always
sending back status code 0. The STA would then reject the commit
response due to expecting H2E/SAE-PK status code.
Just reflect the incoming status code so the commit can be rejected
based on the SAE contents regardless of which variant of SAE was used.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Some legacy stations copy previously reserved RSN capability bits,
including OCVC, in (Re)Association Request frames from the AP's RSNE but
do not indicate MFP capability and/or do not send OCI in RSN handshakes.
This is causing connection failures with such erroneous STAs.
To improve interoperability with such legacy STAs allow a workaround OCV
mode to be enabled to ignore OCVC=1 from the STA if it does not follow
OCV requirements in the first protected exchange. This covers cases
where a STA claims to have OCV capability, but it does not negotiate use
of management frame protection or does not include OCI in EAPOL Key msg
2/4, FT Reassociation Request frame, or FILS (Re)Association Reqest.
The previous behavior with ocv=1 is maintained, i.e., misbehaving STAs
are not allowed to connect. When the new workaround mode is enabled with
ocv=2, the AP considers STA as OCV capable on below criteria
- STA indicates both OCV and MFP capability
- STA sends OCI during connection attempt in a protected frame
Enabling this workaround mode reduced OCV protection to some extend
since it allows misbehavior to go through. As such, this should be
enabled only if interoperability with misbehaving STAs is needed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Initiate SA Query for a WPS+MFP AP. STA flag checks for MFP added for
Association Request frames that use WPS IE without RSNE. This is needed
to avoid giving an opportunity to skip the protection against
disconnections when WPS is enabled.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Resolved the below warning
../src/ap/ieee802_11.c:4535:25: warning: 'reply_res' may be used
uninitialized in this function [-Wmaybe-uninitialized]
if (sta && ((reply_res != WLAN_STATUS_SUCCESS &&
^
Since reply_res is been assigned inside an if condition and so
compiler treats reply_res as uninitalized variable
Initialize reply_res with WLAN_STATUS_UNSPECIFIED_FAILURE.
Fixes: 5344af7d22 ("FT: Discard ReassocReq with mismatching RSNXE Used value")
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
The AP mode condition for initiating the SA Query procedure when
receiving a new (Re)Association Request frame used only association
state and MFP negotiation result without checking that the key exchange
has been completed. This can give rise to a corner case where the SA
Query procedure may get started after open association but before the
4-way handshake has been completed, resulting in open SA query frames
over the air.
Fix this by adding station authorized check in hostapd_notif_assoc() and
check_assoc_ies().
Signed-off-by: Rohan <drohan@codeaurora.org>
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
As per RFC 8110 (Opportunistic Wireless Encryption), if the AP has the
PMK identified by the PMKID and wishes to perform PMK caching, it will
include the PMKID in the Association Response frame RSNE but does not
include the Diffie-Hellman Parameter element.
This was already addressed for most cases with owe_process_assoc_req()
not setting sta->owe_ecdh in case PMKSA caching is used. However, it was
possible to an old STA entry to maintain the initial sta->owe_ecdh value
if reassociation back to the same AP was used to initiate the PMKSA
caching attempt. Cover that case by adding an explicit check for the
time when the Association Response frame is being generated.
Signed-off-by: Chittur Subramanian Raman <craman@maxlinear.com>
Modify the check for VHT to include an option for HE in
hostapd_eid_wb_chsw_wrapper() and its callers to allow the Channel
Switch Wrapper element with the Wide Bandwidth Channel Switch subelement
to be included in Beacon and Probe Response frames when AP is operating
in HE mode without VHT.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Move hostapd_eid_wb_chsw_wrapper() from VHT specific ieee802_11_vht.c to
ieee802_11.c since this can be used for both HE and VHT. This commit
does not change any functionality to enable the HE use case, i.e., the
function is just moved as-is.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Operation in the 6 GHz band mandates valid HE capabilities element in
station negotiation. Reject association request upon receiving invalid
or missing HE elements.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
This was clarified in the draft specification to not be a mandatory
requirement for the AP and STA to enforce, i.e., matching security level
is a recommendation for AP configuration rather than a protocol
requirement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new sae_commit_status and sae_pk_omit configuration parameters and
an extra key at the end of sae_password pk argument can be used to
override SAE-PK behavior for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds AP side functionality for SAE-PK. The new sae_password
configuration parameters can now be used to enable SAE-PK mode whenever
SAE is enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in FT and FILS (Re)Association Request frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
It is possible for drivers to report received Management frames while AP
is going through initial setup (e.g., during ACS or DFS CAC). hostapd
and the driver is not yet ready for actually sending out responses to
such frames at this point and as such, it is better to explicitly ignore
such received frames rather than try to process them and have the
response (e.g., a Probe Response frame) getting dropped by the driver as
an invalid or getting out with some incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Discard the FT Reassociation Request frame instead of rejecting it
(i.e., do not send Reassociation Response frame) if RSNXE Used is
indicated in FTE, but no RSNXE is included even though the AP is
advertising RSNXE.
While there is not really much of a difference between discarding and
rejecting the frame, this discarding behavior is what the standard says
for this type of an error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Response frame so
that a STA not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, hmac_sha256() might fail, so check for that possibility
instead of continuing with undetermined index value that could point to
an arbitrary token entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_auth_reply() could be called with sta == NULL in certain error
conditions. While that is not applicable for this special test
functionality for SAE, the inconsistent checks for the sta pointer could
result in warnings from static analyzers. Address this by explicitly
checking the sta pointer here.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
In the function owe_assoc_req_process(), values assigned to the reason
argument imply that it should be renamed to status. Rename 'reason' to
'status' and modify the uses of owe_assoc_req_process() accordingly.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
(Re)Association Response frames should include radio measurement
capabilities in order to let stations know if they can, e.g., use
neighbor requests.
I tested this commit with a Samsung S8, which does not send neighbor
requests without this commit and sends them afterwards.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.
See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
