This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was only a single file remaining in this directory. All the other
old test functionality has been moved under the top level tests
directory. Move the remaining file to the wpa_supplicant directory to
get rid of the subdirectory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The old wpa_supplicant/Makefile target test-eap_sim_common did not work
anymore and anyway, this test is better placed in the newer hwsim
framework to make sure the test case gets executed automatically.
Signed-off-by: Jouni Malinen <j@w1.fi>
These wpa_supplicant test programs have not been maintained for years
and it would take significant effort to get these into working state.
Since there does not seem to be any real need for these based on lack of
maintenance, it is easier to just drop these tools for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Some drivers do not support having two station interfaces, so the fact
that wpa_supplicant always creates a new interface in station mode, even
if it will be used as another type of interface, may prevent
wpa_supplicant from creating new interfaces. Allow setting the interface
type when a new interface is created so that interfaces of supported
types can be created.
Currently supported types are station ("sta") and AP ("ap"). If the
interface type is not specified, a station interface will be created.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When clearing pending TX action to start a new P2P operation like
P2P_FIND or P2P_LISTEN, wpas_p2p_action_tx_clear() was used to clear
the send action work. However, in cases where the action work has wait
time, it is not cleared immediately but only after the wait time ends.
This may cause delay in starting the P2P operation.
Fix that by always clearing the send action work immediately on these
P2P commands that result in immediate P2P state change and practically
stopping a previous operation, if one was pending.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2a6f78fbbe ('Do not re-associate on
SELECT_NETWORK to current network') started skipping all SELECT_NETWORK
connection steps if the selected network had already been selected
previously. This happened regardless of whether the connection was
already established. This is not necessarily desirable for all cases
where there is no immediate action to even try to connect (e.g., long
wait for the next scan).
Speed this up by allowing the SELECT_NETWORK operation to get started if
there is no connection or ongoing connection attempt with the selected
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Set WLAN_STA_WMM flag to Mesh STA by default since Mesh STAs are QoS
STAs. Mesh STA's HT capabilities won't be parsed properly without the
flag.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the message after message send in
wpas_dbus_signal_p2p_invitation_received() to avoid leaking memory.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
The upstream wpa_supplicant uses the dbus-1 library when it is compiled
with D-Bus support. In Android, we imported the D-Bus shared libraries
under the name "libdbus", so use this shared library instead of dbus-1
when compiling wpa_supplicant with D-Bus support.
Signed-off-by: Samuel Tan <samueltan@google.com>
This is similar to SAVE_CONFIG on control interface, which allow users
to update the configuration file.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
WNM Sleep Mode Response frame is used to update GTK/IGTK only if PMF is
enabled. Verify that PMF is in use before using this field on station
side to avoid accepting unauthenticated key updates. (CVE-2015-5310)
Signed-off-by: Jouni Malinen <j@w1.fi>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
The SCAN TYPE=ONLY results do not trigger a connection operation
automatically. As such, there was no explicit operation that would
change wpa_state after such a scan-only operation and WPA_SCANNING state
could have been left in effect until the next operation is triggered by
an external command. This is not desirable, so restore the wpa_state
that was in use when the scan was started in case WPA_SCANNING state is
still set when the scan operation completes.
This was triggered by the following mac80211_hwsim test sequence:
dbus_wps_oom scan_trigger_failure
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, wnm_deallocate_memory() was called only if we decided to
move to another BSS at the completion of an accepted BSS Transition
Management Request. This resulted in the candidate information being
left in effect for the following scan operation if we were already
associated with the preferred candidate. This could result in unexpected
behavior in the following connection attempt.
Fix this by clearing the candidate information even if we do not need to
roam to another BSS.
This was triggered with mac80211_hwsim test cases in this sequence:
wnm_bss_tm ap_track_sta_force_2ghz
Signed-off-by: Jouni Malinen <j@w1.fi>
libwpa_test1 and libwpa_test2 targets can now be used to check
libwpa_client linking for static and shared library cases respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
Building libwpa_client requires src/utils/common.c for bin_clear_free()
else loading the library fails with:
Error relocating /usr/lib/libwpa_client.so: bin_clear_free: symbol not found
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
All interface globals are now exposed as D-Bus properties of type
string, and parsed via the normal interface global parsing functions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hmac_sha256_kdf() got pulled in only if CONFIG_ERP=y is set. Fix
test_sha256() by making the test case conditional on the function being
present.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is useful for logrotate to be able to rotate the file even if the
control interface is not enabled (e.g., when using DBus).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Linux packet socket workaround(*) has an impact in performance when the
workaround socket needs to be kept open to receive EAPOL frames. While
this is normally avoided with a kernel that has the issue addressed by
closing the workaround packet socket when detecting a frame through the
main socket, it is possible for that mechanism to not be sufficient,
e.g., when an open network connection (no EAPOL frames) is used.
Add a build option (CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y) to disable the
workaround. This build option is disabled by default and can be enabled
explicitly on distributions which have an older kernel or a fix for the
kernel regression.
Also remove the unused variable num_rx.
(*) Linux kernel commit 576eb62598f10c8c7fd75703fe89010cdcfff596
('bridge: respect RFC2863 operational state') from 2012 introduced a
regression for using wpa_supplicant with EAPOL frames and a station
interface in a bridge.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Instead of trying to associate in configuration that is known to result
in the AP rejecting the association, reject the BSS candidate based on
the MFPR=1 RSN capability when STA configuration has PMF disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This element is required to have at least four octets of actual payload.
This was not previously verified before use and the extra buffer data
after the IE might have been used instead if a received WNM-Sleep Mode
Response frame was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
This moves the type cast needed for the current driver interface to
ieee802_11_set_tfs_ie() to allow the WNM-Sleep parsing routines to use
const pointers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
Vendor specific IEs added to frame type P2P_ASSOC_RESP are saved in
the interface context, but as they are added as part of the P2P IEs,
they need to be saved in the global P2P context.
Fix this by directing vendor specific IEs added to P2P_ASSOC_RESP
frame type to the P2P context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
