Commit graph

3292 commits

Author SHA1 Message Date
Mikael Kanstrup
5c6c315fba Add IPv4 support function for "get" control interface command
Add support to retrieve IPv4 config variables with the "get" control
interface command. This allows the ip_addr_* parameters for P2P+NFC
IP address assignment to be fetched from the GO.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-03-15 20:57:16 +02:00
Jouni Malinen
74fa78b281 Add AVG_BEACON_RSSI to SIGNAL_POLL output
If the driver reports separate signal strength average for Beacon
frames, report that in SIGNAL_POLL output.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-15 20:45:20 +02:00
Jouni Malinen
0f89328575 P2P: Move upper layer SD interaction into a separate file
wpa_supplicant/p2p_supplicant.c has reached almost 10000 lines in length
and was getting a bit inconvenient to edit, so start splitting it into
separate files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-15 20:25:48 +02:00
Jouni Malinen
bc1d23ae1d Add ChangeLog entries for v2.4
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 16:51:02 +02:00
Jouni Malinen
f10487e1af Send CTRL-EVENT-DISCONNECTED on wpa_supplicant AP deinit
This makes the AP mode more consistent with other modes by providing a
matching pair of CTRL-EVENT-CONNECTED and CTRL-EVENT-DISCONNECTED event
messages.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 10:05:05 +02:00
Jouni Malinen
1d246a1db9 Make rate-not-supported debug print more useful
It looks like "hardware does not support required rate 1.0 Mbps" has
started showing up in some hwsim test cases as a reason for failure.
This should not really occur with mac80211_hwsim, so add more details to
the debug print to make it easier to figure out what exactly happened.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 15:35:40 +02:00
Sunil Dutt
c10ca2a66f TDLS: Allow driver to request TDLS Discovery Request initiation
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 21:08:54 +02:00
Jouni Malinen
41312fc7ef mesh: Leave mesh in driver setup if initialization fails
It was possible to leave the driver in mesh point state if upper layer
mesh initialization failed in wpa_supplicant_mesh_init(). With nl80211,
this results in the vif being left in mesh point mode instead of
restoring it to station mode. That seems to break normal functionality,
e.g., for Public Action frame TX/RX. Fix this by restoring station mode
on mesh failure path.

This error could be triggered, e.g., with the following hwsim test case
sequence: wpas_mesh_secure_sae_missing_password
nfc_p2p_static_handover_tagdev_go_forced_freq

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 20:58:56 +02:00
Jouni Malinen
6e9023ea49 DFS: Allow wpa_supplicant AP mode to use non-offloaded DFS
This extends the hostapd-like setup of DFS-in-userspace for
wpa_supplicant AP mode operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:25:13 +02:00
Ahmad Kholaif
bd0f68c473 DFS: wpa_supplicant event processing
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:24:16 +02:00
Ahmad Kholaif
d7f1aa8fd7 DFS offload: P2P changes for autonomous GO
Add P2P changes to allow bringing up P2P autonomous GO on a DFS channel
if DFS functionality is offloaded to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:24:13 +02:00
Jouni Malinen
192ad3d730 Interworking: Clear SCANNING state if no match found
Previously, it was possible for wpa_state to be left at SCANNING if
INTERWORKING_SELECT command failed to find any match. Now the state is
set to DISCONNECTED if the operation terminates because of no matching
networks.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-03 17:03:25 +02:00
Krishna Vamsi
95d7b863ec P2P: Consider 5 GHz channels also for auto GO
When there is no channel preference mentioned by user, auto GO
can be started on any of the 5 GHz channels supported for P2P.
Consider operating classes 115 and 124 which do not require DFS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 17:01:15 +02:00
Jouni Malinen
a51c40aa35 P2P: Fix regression in start-GO/AP through a "fake" scan
Commit 3f9ebc439c ('P2P: Allow AP/GO
interface to be started while P2P-in-progress') moved the
wpa_s->connect_without_scan and wpa_s->last_scan_req checks to an
earlier place within the wpa_supplicant_scan() function without
adjusting wpa_s->last_scan_req. This variable was set between the old
and new location, so the new location needs to use wpa_s->scan_req.

This fixes an issue where AP/GO operations were not properly started in
some operation sequence. Instead, a station mode scan was executed. This
issue could be triggered, e.g., by running the no_go_freq test case
followed by autogo_random_channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 16:45:51 +02:00
Sunil Dutt
dd5c155e2e eap_proxy: Callback to notify any updates from eap_proxy
This commit introduces a callback to notify any configuration updates
from the eap_proxy layer. This is used to trigger re-reading of IMSI and
MNC length.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 12:47:20 +02:00
Jouni Malinen
9feadba141 Remove unnecessary NULL check to make function more consistent
Static analyzers may warn about dereference before NULL check in
wpas_network_disabled() due to the new code added to check
wpa_s->p2p_mgmt. wpa_s cannot be NULL here, so remove the unneeded check
for it later in the function. (CID 106124)

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
1772d348ea P2P: Fix interface deinit for failed group interface initialization
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
3f9ebc439c P2P: Allow AP/GO interface to be started while P2P-in-progress
Do not delay the "station mode scan" that is not really a scan, but a
request to start AP/GO mode operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
bdf0518bb9 P2P: Direct P2P_CONNECT command to proper interface
It is possible for the P2P_CONNECT control interface command to be
issued on an incorrect interface. While the upper layer component should
really use global control interface for this, make this work by
redirecting the command to the correct context if needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:54:39 +02:00
Jouni Malinen
44b9ea5bb2 P2P: Do not allow scan or normal association on cfg80211 P2P Device
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:23:09 +02:00
Jouni Malinen
9542f21f3a Clean up p2p_find command parsing and execution
There is no need to maintain three almost identical copies of the
wpas_p2p_find() call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 21:58:38 +02:00
Daisuke Niwa
fa9f381f20 P2P: Allow a specific channel to be specified in P2P_FIND
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2015-02-28 21:52:56 +02:00
Daichi Ueura
eb78a8d5e3 P2P: Restore P2P_SCAN_SPECIFIC
This reverts commit 3df2f4fe99 ('P2P:
Remove unused P2P_SCAN_SPECIFIC') with a modification to fit the current
code base.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2015-02-28 21:41:38 +02:00
Janusz Dziedzic
c3dabf5a00 Fix merge issue with IBSS VHT support
Commit 563ee1832b ('IBSS: Add support for
VHT80 configuration') got merged in incorrectly with one i/j swap
missed.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-28 16:48:22 +02:00
Jouni Malinen
8b2b718da9 Fix minor issue in HT40 max rate determination
Commit a1b790eb9d ('Select AP based on
estimated maximum throughput') had a copy-paste bug than ended up
leaving one of the max_ht40_rate() cases unreachable. (CID 106087)

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 16:40:58 +02:00
Jouni Malinen
0d2030ee20 Use estimated throughput to improve roaming selection
Previously, within-ESS roaming was skipped if the selected BSS did not
have a higher signal strength than the current BSS regardless of AP
capabilities. This could result in not moving to a BSS that would
provide higher throughput, e.g., due to larger channel bandwidth or
higher rates (HT/VHT MCS).

Use estimated throughput information from scan result processing to
allow within-ESS roaming if the selected BSS is likely to provide better
throughput even if the current BSS has larger RSSI.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:45:45 +02:00
Jouni Malinen
1d747e2a98 Add snr and est_throughput to the BSS entries
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
Jouni Malinen
a1b790eb9d Select AP based on estimated maximum throughput
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.

In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
Jouni Malinen
ab647ffea7 Add wpa_supplicant Makefile target libwpa_ctrl.a
"make -C wpa_supplicant libwpa_ctrl.a" can now be used to build a static
library that can be linked with external programs using wpa_ctrl.h. This
makes it easier to create a separate library package that does not
depend in any other hostap.git file other than src/common/wpa_ctrl.h and
the libwpa_ctrl.a built with this new make target.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-21 17:48:10 +02:00
Matthieu Mauger
71d77adb6d Update current BSS level when signal change event occurs
When an EVENT_SIGNAL_CHANGE occurs the bgscan is informed about this
change but the new RSSI value is not stored. In consequence, when
roaming candidates are evaluated, the RSSI value of the current BSS used
to compare is an old one obtained during the last scan rather than the
new one given by the signal change event. This leads sometimes to bad
decision when selecting a new BSS for roaming.

This patch solves the issue by updating the current BSS level when
receiving a signal change event in order to have a very up-to-date
current signal value when choosing an new BSS.

Signed-off-by: Matthieu Mauger <matthieux.mauger@intel.com>
2015-02-21 16:07:53 +02:00
Ilan Peer
f1609f119a wpa_supplicant: Cancel sched_scan when stopping countermeasures
When stopping the TKIP countermeasures, it would be preferable to
connect immediately. However if scheduled scan is in progress,
a connection attempt will be done only when scan results are received,
so cancel the scheduled scan to allow immediate scan and connection
attempt.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-21 16:07:53 +02:00
Eliad Peller
0b8bcaa50f P2P: Allow configuring CTWindow when working as GO
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.

Use p2p_go_ctwindow=0 (no CTWindow) by default.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-02-21 16:07:53 +02:00
ASHUTOSH NARAYAN
5ce6ac11ab Inteworking: Add support to update the ANQP Capability List into the BSS
In addition, add support for returning the capability list through
the BSS control interface command.

Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
2015-02-21 16:07:53 +02:00
ASHUTOSH NARAYAN
185ada4770 HS 2.0: Add support to update the HS20 Capability List into the BSS
In addition, add support for returning the capability list through the
BSS control interface command.

Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
2015-02-21 16:07:53 +02:00
Arkadiusz (Arkq) Bokowy
7fe7a3a51f wpa_gui: Debug enhancement
Instead of calling a dummy printf function use preprocessor to determine
if debugging mode is enabled. Also use native Qt debug function.

Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
2015-02-21 16:07:53 +02:00
Jouni Malinen
2b892d442a Add forgotten network profile parameters to config file writing
Number of network profile parameters were not written to the
configuration file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-21 16:07:53 +02:00
Janusz Dziedzic
563ee1832b IBSS: Add support for VHT80 configuration
Configure VHT80 based on driver capabilities.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-21 16:07:53 +02:00
Janusz Dziedzic
98479dc95e IBSS: Update operating frequency if joining an existing IBSS
If a matching IBSS is found in scan results, change requested frequency
to match and disable OBSS scan.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-21 16:07:53 +02:00
Janusz Dziedzic
4d9e6fba2a IBSS: Add fixed_freq network parameter
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-21 16:07:53 +02:00
Dmitry Shmidt
6f5e1b0bf6 Use priority list instead of global for PNO
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2015-02-21 16:07:52 +02:00
Rajiv Ranjan
f92446fb7d P2PS: Add P2PS interface info
This adds documentation on P2PS related interface commands and events.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-21 11:28:20 +02:00
Jouni Malinen
59b416c733 Add optional reassoc-to-same-BSS optimization
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 16:35:39 +02:00
Jouni Malinen
c4da67deef Fix passive_scan config parameter writing
Commit c35e35ed81 ('Add passive_scan
configuration parameter') used incorrect parameter name when writing the
passive_scan parameter into a configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 16:22:47 +02:00
Ola Olsson
10263dc2a4 Add control interface commands for fetching wpa_config values
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.

Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
2015-02-08 22:49:58 +02:00
Jouni Malinen
f91a512f1f Add INTERWORKING_ADD_NETWORK command
This can be used to provide more control to upper layers on network
blocks generated as part of Interworking network selection.
INTERWORKING_ADD_NETWORK behaves otherwise identically to
INTERWORKING_CONNECT, but it does not request a new connection after
having added the network block and it returns the network id of the
added network.

INTERWORKING_ADD_NETWORK followed by REASSOCIATE would behave more or
less identically to INTERWORKING_CONNECT, but this allows the created
network profile to be modified, if desired, and/or stored externally.
SELECT_NETWORK can also be used with the network id returned from
INTERWORKING_ADD_NETWORK to enforce that specific network profile to be
used for the next connection (though, it should be noted that this
behavior may not meet all Hotspot 2.0 requirements if there were other
enabled networks that could have higher priority).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 22:49:58 +02:00
Jouni Malinen
5b74e086e6 P2P: Document P2P_CONNECT-auto
Commit b31be3a0fd ('P2P: Add automatic GO
Negotiation vs. join-a-group selection') added this P2P_CONNECT 'auto'
parameter, but did not update any documentation on it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:50 +02:00
Jouni Malinen
99650cadc9 Add STOP_AP control interface command
This is mainly for testing purposes to allow beaconing to be stopped
without clearing AP state in hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:49 +02:00
Jouni Malinen
6b00512164 P2P: Add event messages for P2P_CONNECT-fallback-to-GO-Neg
This makes it easier for upper layer programs to follow progress of
P2P_CONNECT-auto operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:48 +02:00
Jouni Malinen
b0e669beeb P2P: Fix P2P_CONNECT-auto fallback to GO Neg with group interface
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.

When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:14 +02:00