The reason_detail field was removed from the implementation, so the test
cases need matching changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add testcase to verify a failed reconnect attempt due to authentication
timeout blacklists the correct AP. Driver capabilities are forced to
non-SME and driver roaming (BSS selection) mode.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Add testcase to verify failed roaming attempt due to authentication
timeout blacklists the correct AP. Roaming attempt is performed
with the reassociate command and bssid_set=1. Driver capabilities
are forced to non-SME and driver roaming (BSS selection) mode.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Clear wpa_supplicant scan cache before starting these test cases since
the ROAM command depends on the correct BSS entry being found.
scan_for_bss() does not enforce that correct entry to be present if
there was an earlier BSS entry with the same BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the wpa_supplicant debug entries from the end of a test case
using a dynamically added wlan5 interface to the correct test case,
i.e., the test case that added the interface instead of whatever test
case happens to follow this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some tests call the check_qos_map() function more than once. Make sure
each test sets up wlantest only once before the first time the function
is called.
The wlantest setup sets the channel for the wlantest interface and
executes the wlantest executable. It is more efficient to do that only
once for each test.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Some operations take longer time on real hardware than on hwsim. This
commit increases two timeouts so that the tests will pass on real
hardware, too.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use increased timeouts for connect and disconnect since these operations
take a longer time on real harware than they do on hwsim.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
It looks like the attempt to read the process id from a PID file can
return empty data. This resulted in kill_pid() failing to kill the
process and all the following FST test cases using the extra interface
failing. While the PID file is really supposed to have a valid PID value
when we get this far, it is better to try multiple times to avoid
failing large number of test cases.
The current os_daemonize() implementation ends up calling daemon() first
and then writing the PID file from the remaining process that is running
in the background. This leaves a short race condition where an external
process that started hostapd/wpa_supplicant could end up trying to read
the PID file before it has been written.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d6a526ac3 ('tests: Make
ap_wps_er_http_proto more robust') tried to work around the timeouts
here, but that was not really the best approach since the one second
timeout that was used here for connect() ended up being very close to
the limit even before the kernel change. The longer connect() time is
caused by a sequence where the listen() backlog ignores the connection
instead of accept() followed by close() within the wpa_supplicant ER
HTTP connection handling. The time to retransmit the SYN changed a bit
in the kernel from 1.0 sec to about 1.03 sec. This was enough to push
that over the one second timeout.
Fix this by using a sufficiently long timeout (10 sec) to allow SYN
retransmission to occur to recover from the listen() backlog case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like connect() for a TCP socket can time out at least with a
recent kernel. Handle that case more gracefully by ignoring that socket
while allowing the test to continue.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it is possible for the separate started wpa_supplicant
process to remain running after a test case like fst_sta_config_default.
This would result in failures to run any following test case that uses
the wlan5 interface. Try to kill the process more thoroughly by waiting
for the PID file to show up and write more details into the logs to make
it easier to debug issues in this area.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use a smaller fragment_size to force the roundtrip limit to be reached
with OpenSSL 1.1.0 which seemed to result in a bit shorter TLS messages
being used and being able to complete the authentication successfully
with the previously used fragment_size value.
Signed-off-by: Jouni Malinen <j@w1.fi>
