- CMAC and GMAC modes
- 128-bit and 256-bit modes
- normal BIP and BIP using BCE
- test vectors with minimum and optional additional header elements in
S1G beacon frames
- S1G Beacon Compatibility element in some cases, no other beacon body
components
Signed-off-by: Henry Ptasinski <henry@e78com.com>
Signed-off-by: Andrew Pope <andrew.pope@morsemicro.com>
Signed-off-by: David Goodall <dave@morsemicro.com>
Make this function more capable to address cases where a specific
affiliated link of an AP MLD needs to be found.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When FT over-the-DS is used with MLO, the Target AP Address field is
expected to identify the AP MLD using its MLD MAC address.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The Key MIC field is of variable length when using OWE, so determine the
correct length based on which group was negotiated for OWE during
association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to derive the PTK correct when Secure LTF support is used
and the additional KDK component needs to be taken into account.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Commit b20991da69 ("wlantest: MLD MAC Address in CCMP/GCMP AAD/nonce")
updated AAD and nonce construction to use MLD addresses in AAD for A1
and A2. IEEE P802.11be has additional cases where A3 in AAD is set to
the AP MLD address, so cover those as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for there to be multiple STA entries (e.g., one for each
BSS) when a sniffer capture contains multiple associations using MLO.
For such cases, the new PTK information needs to be updated to all
existing STA entries to be able to find the latest TK when decrypting
following frames since the other STA entries might be located first when
trying to figure out how to decrypt a frame.
In addition to the PTK, copy the MLD MAC addresses to the other STA and
BSS entries to make sure the latest values are used when trying to
decrypt frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend wlantest capabilities to cover the new SAE-EXT-KEY AKM and
variable length MIC field and key lengths for it based on the used SAE
group.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow a single STA entry to be found for a non-AP MLD regardless of
which link MAC address was used to transmit/receive it.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the MLD MAC Address instead of link address in CCMP/GCMP AAD/nonce
construction when processing an individually addressed Data frame with
FromDS=1 or ToDS=1 between an AP MLD and non-AP MLD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE P802.11be indicates the MLD MAC addresses, i.e., the Authenticator
and Supplicant addresses, in the MAC Address KDE in EAPOL-Key msg 1/4
and 2/4. Learn those addresses so that wlantest can be extended to
support MLO.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Reassemble the full MSDU when processing TKIP protected fragmented
frames so that the Michael MIC can be validated once the last fragment
has been received.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be useful for debugging, so return successfully decrypted TKIP
frame even if the Michael MIC cannot be verified (fragment reassembly
not yet supported) or if the Michael MIC value is incorrect. Add a note
in the frame to point out that the Michael MIC was not verified or is
incorrect.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows correct processing of Data frames with Mesh Control field by
finding the LLC/SNAP header after that field.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the TKs from the PTK file (-T command line argument) to try to
decrypt encrypted Management frames if no BSS/STA key can be found based
on addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is expected for the STA entry on the target AP to move directly from
State 1 to State 3 when performing FT over-the-DS (i.e., FT Action
Request/Response frame exchange through the old AP followed by
Reassociation Request/Response frame exchange with the target AP).
Signed-off-by: Jouni Malinen <j@w1.fi>
If no Beacon or Probe Response frame has been seen in the capture, use
the IEs from EAPOL-Key msg 3/4 to set up BSS information.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation tried to update STA IE information based on
EAPOL-Key msg 2/4 to be able to handle captures that do not include the
(Re)Association Request frame. This was not sufficient (OSEN was not
included) and was done too late (the parsed information is needed for
PMK-to-PTK derivation).
Move the IE update step to happen before trying to derive the PTK if no
(Re)Association Request frame has been seen.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fetch the BIGTK from EAPOL-Key msg 3/4 and use it to validate MME in
Beacon frames when the AP uses Beacon protection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow option (command line argument -e) to capture Ethernet headers
instead of IEEE 802.11 so that wlantest can be used as a replacement for
tcpdump/dumpcap for capturing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Track PMK-R0/PMK-R0-Name from the initial mobility domain association
and derive PMK-R1/PTK when the station uses FT protocol. This allows
frames from additional roaming cases to be decrypted.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a sniffer capture does not include FCS for each frame, but may
included frames with invalid FCS, it would be possible for wlantest to
try to decrypt the first received frame and fail (e.g., due to CCMP MIC
mismatch) because that particular frame was corrupted and then ignore
the following retry of that frame as a duplicate even if that retry has
different payload (e.g., if its reception did not show corruption).
Work around this by skipping duplicate frame detection immediately
following a decryption failure.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wlantest used to ignore RSN/WPA/OSEN element in (Re)Association Request
frame if no Beacon frame had been seen from the AP before the
association exchange. This could result in not being able to derive keys
properly. Work around this by skipping that step if the BSS entry is not
yet complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The length of the TK is available within struct wpa_ptk, so there is no
need to try to maintain it separately in wlantest.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Try to derive PTK when FILS shared key authentication is used without
PFS. The list of available PMKs is interpreted as rMSK for this purpose
and PMK and PTK is derived from that. If the resulting PTK (KEK) can be
used to decrypt the encrypted parts of (Re)Association Request/Response
frames, mark the PTK as derived so that encrypted frames during the
association can be decrypted. In addition, write a decrypted version of
the (Re)Association Request/Response frames into the output file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the CRC-32 routine to be shared for other purposes in
addition to the WEP/TKIP/FCS within wlantest.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to do live parsing of captured pcap files from
wlantest without having to rename and restart the capture file. Packet
writes are flushed to disk after each packet if -N is included in the
command line.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds minimal support for deriving keys for FT-PSK to allow the
initial mobility domain association to be analyzed in more detail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This allows Hotspot 2.0 OSEN connection to be analyzed more
conveniently. The frames from an OSEN association can now be decrypted
using an MSK file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A text file with a hexdump of PTK (KCK|KEK=TK with 48 octets for CCMP or
64 octets for TKIP or alternative 16 or 32 octet TK for CCMP/TKIP) can
now be read from a file specified with the -T command line argument. If
the current known PTK fails to decrypt a frame (or if no current PTK is
known) all listed PTKs are iterated to see if any of them matches.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new -n<file> command line argument can be used to request wlantest
to write all read or captured frames into a pcapng file. This is similar
to the -w argument, but with pcapng allowing per-frame comments to be
embedded in the file.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using DLT_IEEE802_11 datalink type in a pcap file, wlantest can now
be instructed to assume there is an FCS included in the frame by adding
the new -F command line argument. This will make wlantest validate the
FCS and strip it from the frame before processing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
