The 4-way handshake fails with the error "WPA: No wpa_ie set - cannot
generate msg 2/4" while connecting to OSEN network with drivers that
indicate used Association Request frame elements because OSEN IE is not
handled in wpa_supplicant_event_associnfo() if data->assoc_info.req_ies
is not NULL.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.
Signed-off-by: Naveen Singh <nasingh@google.com>
An interface can be disabled while it has an ongoing scan request.
In such a case, when the scan results notification is received,
it was being ignored (as the interface is already disabled) so the
scan state was not cleared. This can cause undetermined behavior
for the next scan request.
To handle this, clear the scan state when EVENT_SCAN_RESULTS is
received and the interface is disabled.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Commit 02e122a995 ('Reschedule scan from
wpas_stop_pno if it was postponed') uses wpa_s->scanning as the only
condition for automatically starting a postponed scan request from
EVENT_SCHED_SCAN_STOPPED event handler. However, wpa_s->scanning may be
set for sched_scan and as such, this can result in unexpected extra
scans without there having been any real postponed request.
Make this more accurate by verifying that there really is a pending
request for a scan before speeding up its start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If WPA2 is used, MBO AP must enable PMF. Refuse to select a BSS that has
MBO and WPA2 enabled without PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Previously, when wpa_supplicant received bgscan results with a preferred
network, it connected to that network without disconnecting from the
previous one. This might result in an inconsistent state of upper
layers.
Fix this by disconnecting from the current AP before connecting to the
new one when the network profile changes and there is an existing
connection.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
If scan results arrive during the connection process, the network
selection function was called, interrupting the current connection.
While a regular scan is mutually exclusive with connection establishment
via the nature of radio work, there's no such protection for scheduled
scan. Prevent network selection while a connection is in progress.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of trying to associate in configuration that is known to result
in the AP rejecting the association, reject the BSS candidate based on
the MFPR=1 RSN capability when STA configuration has PMF disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Channel switch notification was handled only for AP/GO interfaces. As
the notification can be sent on other interface types as well, extend
the handling to handle other interface types.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for driver-based BSS selection to end up reassociating
back to the current AP. If wpa_supplicant preferred another BSS, it
would have updated the internal knowledge of the AP's WPA/RSN IE when
requesting a new connection. In the special case of existing association
and new association being with the same BSS that is different from the
wpa_supplicant preference, association event processing skipped the
WPA/RSN IE update. This could result in the following 4-way handshake
getting rejected due to incorrectly detected mismatch with AP's RSN/WPA
IE between Beacon/Probe Response frame and EAPOL-Key msg 3/4.
Fix this by updating the AP WPA/RSN IE on all association events when
driver-based BSS selection is used regardless of whether the BSSID
changes. This could also cover a theoretical case of the AP changing its
RSN/WPA IE at the very moment we try to reassociate back to the same
BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PNO was stopped by the wpa_supplicant during the connection attempts or
while handling disassociation indication. External entities, mainly, the
Android Wi-Fi framework, does not expects PNO to be stopped by other
modules. Hence, do not stop the sched_scan in these scenarios if it is
triggered externally for PNO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.
To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update hardware features for all interfaces inside the loop, don't treat
the calling wpa_s instance specially. Perform the P2P channel list
updates after the hardware features are updated. This will prevent P2P
from relying on stale information.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Remove the code that considers removing GOs from their current
channel due to frequency interference, as this is already handled
as part of the P2P channels update.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This variable is needed to figure out whether a wpa_supplicant interface
is for a P2P group that is (or was) connected to a specific GO. The
previous implementation was able to find such a case only when there was
an association with the GO. However, this may be needed even if there is
a temporary disconnection from the GO. Keep the GO device address
information over such temporary disconnections and only remove it on
group termination. This fixes an issue with D-Bus Peer PropertiesChanged
signals for the Groups property in case a P2P group gets removed due to
group idle timeout instead of explicit group termination command (local
request) or GO notification.
Signed-off-by: Jouni Malinen <j@w1.fi>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.
Signed-off-by: Jouni Malinen <j@w1.fi>
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.
In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.
In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reschedules the postponed scan request (if such a request is
pending) from EVENT_SCHED_SCAN_STOPPED event handler to speed up
scanning after PNO/sched_scan stop has been requested.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Commit e9af53ad39 introduced new
CONFIG_NO_ROAMING configuration parameter but unfortunately it was added
only to Android.mk. Enabling this parameter didn't have any effect when
Makefile was used to build wpa_supplicant. This commit fixes that problem
and cleans "unused variable" compiler warning.
Signed-off-by: Lauri Hintsala <lauri.hintsala@silabs.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The channel list can be changed as a result of arriving beacon hints
during normal scan or as a result of local Reg-Domain change. Some
passive channels can become active and needs to be reconfigured
accordingly for the scheduled scan.
This fixes the connection to hidden SSIDs on 5 GHz band during default
Reg-Domain 00 (world roaming).
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
It looks like "hardware does not support required rate 1.0 Mbps" has
started showing up in some hwsim test cases as a reason for failure.
This should not really occur with mac80211_hwsim, so add more details to
the debug print to make it easier to figure out what exactly happened.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, within-ESS roaming was skipped if the selected BSS did not
have a higher signal strength than the current BSS regardless of AP
capabilities. This could result in not moving to a BSS that would
provide higher throughput, e.g., due to larger channel bandwidth or
higher rates (HT/VHT MCS).
Use estimated throughput information from scan result processing to
allow within-ESS roaming if the selected BSS is likely to provide better
throughput even if the current BSS has larger RSSI.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an EVENT_SIGNAL_CHANGE occurs the bgscan is informed about this
change but the new RSSI value is not stored. In consequence, when
roaming candidates are evaluated, the RSSI value of the current BSS used
to compare is an old one obtained during the last scan rather than the
new one given by the signal change event. This leads sometimes to bad
decision when selecting a new BSS for roaming.
This patch solves the issue by updating the current BSS level when
receiving a signal change event in order to have a very up-to-date
current signal value when choosing an new BSS.
Signed-off-by: Matthieu Mauger <matthieux.mauger@intel.com>
When stopping the TKIP countermeasures, it would be preferable to
connect immediately. However if scheduled scan is in progress,
a connection attempt will be done only when scan results are received,
so cancel the scheduled scan to allow immediate scan and connection
attempt.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.
When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
It was possible for the interface not to be marked in INTERFACE_DISABLED
state in case the event was processed for P2P GO because the wpa_s
instance could have been removed in case of a separate group interface.
Change the state first to avoid leaving different state for the case
where separate group interface is not used.
Mark scan to be a normal scan on INTERFACE_ENABLED so that scanning
rules (e.g., skip scan if no networks enabled) get used consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a race condition between receiving an AP stopped event and
netdev down event. These resulted in different group removal reasons on
a GO device (UNAVAILABLE for stop AP event coming first and REQUESTED
for netdev event first). Make this more consistent by reporting
UNAVAILABLE for both possible cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.
Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
In case of roaming, we don't get disassoc notification, but
still want to remove the existing tspecs.
Move the wmm_ac_notify_disassoc() call to the state change
function, which get called also on roaming.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.
For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.
Signed-off-by: Jouni Malinen <j@w1.fi>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.
wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The commit 5cd4740580 has rearranged the
update scan results code and hence the IEs were not getting updated
properly for ap_scan=1 case. This can result in a 4-way handshake
failure in the roaming case (IE mismatch in 3/4 EAPOL). Fix this by
updating the scan results even if ap_scan=1 is used and network does not
need to get reselected based on association information.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Incorrect field was used to determine the init=<value> in the regulatory
domain changed control interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
The radio works for the interface get removed if interface is disabled.
This could have left P2P module in invalid state if the interface got
disabled during a p2p_find or p2p_listen operation. Clear the state in
such a case to avoid blocking following operations due to P2P module
assuming it is still in progress of doing something.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
No need to call ibss_rsn_deinit() again since it is already being called
by wpa_supplicant_mark_disassoc().
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an ANQP fetch is triggered and ANQP_3GPP_CELLULAR_NETWORK info is
required, initialize scard to be ready when comparing ANQP and
credentials.
Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 3d910ef497 tried to make
last-network selection behave more consistently with Interworking
network selection preferences. However, it did not take into account
that other network block may have higher priority. In such cases, the
last added network from Interworking network selection should actually
not be selected for the next connection. Fix this by limiting the
last-network preference to work only within a priority class.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it would have been possible for the network to be marked
disabled and that marking to be ignored if a recoverable disconnection
reason event were processed. Avoid this by verifying network status
before trying to reconenct back to the same BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpa_s->current_bss was updated too late for the
wpa_supplicant_rsn_supp_set_config() call within
wpa_supplicant_select_config(). Re-order code so that current_bss gets
updated between current_ssid update and this call to set the WPA state
machine configuration, so that the new code that determines whether the
current GO support the new IP address assignment mechanism works.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Conver Public Action
GAS queries to use Dual of Public Action frame if PMF has been
negotiated with the AP to which the frame is being sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scan request failures are observed in wpa_supplicant debug log when
Android framework starts PNO scan in driver via ctrl interface command
'set pno 1' and wpa_supplicant also tries to issue a scan request after
PNO has started in the driver.
Some drivers may reject a normal scan request when PNO is already in
progress. wpa_supplicant should consider PNO status before issuing start
scan request to the driver. Otherwise, wpa_supplicant will get failures
from driver for the scan request and it will end up rescheduling scan
request in periodic interval and get a start scan request failure for
each attempt.
In order to avoid unnecessary scan attempt when PNO scan is already
running, PNO status is checked before issuing scan request to driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch resets the static interface_count to zero in case of
wpa_supplicant_driver_init() call for wpa_s which is in
INTERFACE_DISABLED state. This interface_count is used for the delay of
the scan which is now minimal for dynamically added interfaces. This may
collide with a scan for another interface, but the same is true for any
chosen delay in this scenario. Also the state change to DISCONNECTED is
moved to wpa_supplicant_driver_init() so it will move from
INTERFACE_DISABLED to INACTIVE when there are no enabled networks.
Tested-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_s->scan_res_handler is set only for cases where a scan operation is
requested for a specific purpose. As such, this callback should only be
called when a scan result from a scan that was triggered by
wpa_supplicant is processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, the shorter scan interval was already in use for the
connection following the provisioning step, but same optimization can
also be used for the pre-provisioning scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It may not always be desirable to trigger reassociation or network
change based on scan results from externally to wpa_supplicant trigger
scan operations. Skip network selection and roaming determination if the
received scan result is known to be triggered by something external to
wpa_supplicant. The control interface SCAN command can be used to
request wpa_supplicant to determine the best network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
An INTERFACE_DISABLED event received on an interface that is
currently operating a P2P GO means that the group session ended.
In such a case, if the interface was dynamically added remove it, and
if not, remove all the network blocks that are temporary, assuming
that if needed a new session will be started by an external entity.
The use case was triggering rfkill (both SW and HW). This case popped up
as part of a testing cycle, where after a toggle in the rfkill state,
the result was that the interface was not deleted, but on the other hand
the wpa_supplicant did not configure the kernel to re-start the AP
functionality again.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).
If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.
This patch fixes this issue by restoring the previous scan_req value.
Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
The shorter 250 ms wait for the next scan request can be used also for
the case of persistent group re-invocation instead of just formation of
a new group. This speeds up the process and makes this more robust
especially in cases where the GO is using MCC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The QoS Map Set element was passed in full to the driver instead of just
the payload of the element. This resulted in the updated QoS Map being
rejected. Validate the element id/len and send only the payload to the
driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Request new scan only for the interface for which the original scan
request and results has come. Otherwise while sharing scan results along
with P2P interfaces, the new scan will be requested on P2P interfaces.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This is a better way of matching P2P groups based on the unique P2P
Device Address (e.g., from P2P Group ID) and SSID pair instead of using
the not necessarily unique P2P Interface Address.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_setup_channels function uses the per interface information
(wpa_s->hw.modes) for setting up the available channel list for P2P
operation, but if a separate P2P interface is used (e.g., p2p0 on
Android), the wpa_s instance for that interface may not get an updated
channel list. This can result in some operations, like "P2P_SET
disallow_freq", using old channel list information (e.g., world roaming
information with passive-scan/no-ibss flags) which was initialized
during the start-up. This could result in P2P functionality using
conflicting or obsolete channel information.
To resolve this issue, update channel list information on regulatory
change events to all of the virtual interfaces sharing the same phy for
which the event is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P-GROUP-STARTED event depends on having enough information about the
group available. To avoid incomplete information from being delivered to
upper layers, do not accept scan results without P2P IE (e.g., from a
non-P2P scan) for P2P client association process. This can be of use for
some join-a-group cases where non-P2P scans have generated the BSS entry
for the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now in case of deauthentication from GO, immediate group removal will
happen in GC only if the deauthentication packet has a valid IE. However,
the IE in deauthentication packet is mandated only for managed P2P group.
So in normal P2P group the group removal is delayed and will happen later
only in group idle timeout.
This fixes a regression from commit
d7df0fa727 that changed the previous check
for data->deauth_info != NULL to data->deauth_info->ie != NULL.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wpa_supplicant behavior in WEP configuration was to try to
mimic a device that is not aware of WPA/WPA2 and as such, it tried to
connect to a WPA/WPA2 AP with the assumption that the AP could be
providing support for both WEP and WPA/WPA2 stations in the same BSS.
Such APs could have been used during transition from WEP to more secure
options, but that type of deployment have not been used in large number
and are not really of much use anymore taken into account that more or
less all new devices support WPA/WPA2. That combined with the preference
to deprecate WEP justifies removing this use case and making WEP
networking matching more strict by using the knowledge of AP advertising
WPA/WPA2 as an indication of WEP not being supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To better support the IBSS/RSN mechanism, wpa_supplicant has to be able
to detect a possible peer reboot and in this case it should start a new
EAPOL handshake.
To perform such reboot detection wpa_supplicant has to perform an Open
Authentication by sending an Authentication frame and then replying to
it. IF an Authentication frame is received when the key have already
been exchanged, wpa_supplicant understands that the peer has rebooted
and can reset its state machine.
Whenever a new peer is added to the IBSS wpa_supplicant will start the
Open Authentication and only after having accomplished it will start the
key exchange. If the driver does not support Authentication frame
exchange initiated from user space, this step is skipped to maintain
previous behavior (just go through EAPOL-Key frame processing).
The Open Authentication was partly supported by the Linux kernel but now
wpa_supplicant can register for Authentication frames, handle it in
userspace and so avoid any possible race condition.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
Signed-hostap: Antonio Quartulli <antonio@open-mesh.com>
This allows wpa_supplicant to associate to an AP that has VHT BSS
membership selector set to indicate VHT support is required for the BSS.
Without the patch it was impossible to connect to, e.g., hostapd-based
AP that has require_vht=1. wpa_supplicant was complaining with:
hardware does not support required rate 63.0 Mbps
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
wpa_s->pending_bssid is all zeros during connection attempt when
driver-based BSS selection is used. Take this into account when
determining whether new scan results should trigger a connection based
on wpa_s->current_ssid, i.e., a connection attempt with the selected
network instead of selected BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not requesting the auto connect on
dissassociation event if we are already in disconnected state and would
not try to connect anyway.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The fast-connect optimization to skip a new scan did not update how the
RSN preauthentication callback is used. There is no point in trying to
add preauthentication candidates from cases where scan was skipped, so
skip this call, too, in such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Scan result events are shared between all virtual interfaces sharing the
same radio. However, some of the steps are not really appropriate on
virtual interfaces that did not issue the scan request. Fix this by
making these steps conditional on the scan results being processed on
the interface that requested them.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6a1ce39599 moved the bssid
variable declaration to be outside CONFIG_IEEE80211R block and
triggered a compiler warning about unused variable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
Usual manual scan request may cause reassociation due to several
reasons. New command is intended to perform pure scan without taking any
automatic action based on the results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
On the DMG (60 GHz) band, capability bits defined differently from
non-DMG ones. Adjust capability matching to cover both cases.
Also, for non-DMG bands, check ESS bit is set.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Addition of wpa_supplicant_fast_associate() made it unnecessary to call
wpas_select_network_from_last_scan() directly from other files.
Signed-hostap: Jouni Malinen <j@w1.fi>
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision. This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.
Signed-hostap: Paul Stewart <pstew@chromium.org>
The link was not disabled for the case of implicit trigger from the
driver unlike in the case of explicit trigger fromc ctrl_iface. Make the
tear down sequences match in these cases by adding the TDLS_DISABLE_LINK
tdls_oper to the driver when processing the TDLS_REQUEST_TEARDOWN event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The WNM-Sleep Mode handler took over WNM Action frame processing without
addressing the previously implemented WNM handler. Fix this by moving
the BSs Transition Management processing into wnm_sta.c to share a
single handler function for WNM Action frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.
Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.
This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prevents situations like the following where we roam to a
lesser quality BSS just because the signal level delta is over our
threshold.
wlan0: Considering within-ESS reassociation
wlan0: Current BSS: 00:24:6c:74:0a:40 level=-51
wlan0: Selected BSS: 00:24:6c:74:0a:e0 level=-64
wlan0: Request association: reassociate: 0 selected: 00:24:6c:74:0a:e0
bssid: 00:24:6c:74:0a:40 pending: 00:00:00:00:00:00 wpa_state: COMPLETED
Signed-hostap: Robert Shade <robert.shade@gmail.com>
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver indicates the association (or authentication) was
rejected, wpa_supplicant should handle this connection failure similarly
to other cases. Previously, this was only handled with drivers that use
wpa_supplicant SME.
In case of cfg80211-based drivers, a rejected association was actually
already handled since cfg80211 generates a deauthentication event after
indicating connection failure. However, rejected authentication resulted
in wpa_supplicant waiting for authentication timeout to expire which is
unnecessary long wait.
Fix this by calling wpas_connection_failed() to use the common mechanism
to reschedule a new connection attempt with the previously attempted
BSSID blacklisted.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add a function to filter out known cases of disconnection during 4-way
handshake that are caused by something else than mismatch in PSK. This
commit adds the case where the local end determines a mismatch in
WPA/RSN element between Beacon/Probe Response frames and EAPOL-Key msg
3/4.
This can avoid some potentially confusing "WPA: 4-Way Handshake failed -
pre-shared key may be incorrect" ctrl_iface messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If two P2P_FIND commands and a station mode SCAN command are issued in a
sequence with the second P2P_FIND and SCAN commands started before the
initial scan from the first P2P_FIND command has completed,
sta_scan_pending may be left set without an automatic way of getting it
cleared. This can get P2P search stuck if no further station mode scan
operations are run.
Fix this by clearing the sta_scan_pending flag whenever station mode scans
are stopped due to no enabled networks resulting in INACTIVE mode getting
entered. In addition, avoid setting sta_scan_pending flag when a special
scan_res_handler is set so that this does not get enabled on the P2P
Device interface during a P2P search operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a connection operation is started on an interface based on scan
results, other virtual interfaces should not be information about the
results to avoid potential concurrent operations during the association
steps. Since the sibling notification of scan results received was added
as an optimization, skipping it for this type of cases is the simplest
way of avoiding unnecessary concurrent operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes sure that the interrupted station mode scan can be completed
after the P2P operations have had their chance of using the radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the scan results from before ANQP fetch are fresh (less than five
seconds old), do not run a new scan when selecting the BSS after having
used Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.
Signed-hostap: Jouni Malinen <j@w1.fi>
The same information is available in the BSS table, so we can reduce the
need for using the raw scan results in wpa_supplicant_need_to_roam().
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This broke SME
disassoc-while-authenticating workaround for cfg80211. Fix this by
restoring wpa_s->current_ssid in case SME authentication is in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).
Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The variables used within the #ifndef block here needs to be defined in
the beginning of the function to avoid issues with some compilers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.
Signed-hostap: Jouni Malinen <j@w1.fi>
The os_memcmp of bssid and wpa_s->bssid cannot return 0 in this
code path since identical os_memcmp was already done above.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the normal flow for association:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return BSSID )-- device driver
However, a device driver could return EINVAL for get_bssid() because it
recognizes it has already been disconnected. When the wpa_supplicant
received EINVAL, the bssid field could be used uninitialized in the
following flow:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
device driver (receive deauth)
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return EINVAL )-- device driver
Prevent this by requiring the get_bssid() call to succeed when
processing association events.
When a special scan_res_handler is used the scan parameters may not have
been suitable for other purposes (e.g., during a p2p_find operation). As
such, do not indicate such scan results to other virtual interfaces
using the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
In the properties changed signal, added a new property
"DisconnectReason", which carries the IEEE 802.11 reason code of the
most recent disassociation or deauthentication event. The reason code is
negative if it is locally generated. The property is sent to the DBUS
immediately so as to prevent it from being coalesced with other
disconnect events.
Signed-off-by: Gary Morain <gmorain@chromium.org>
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.
Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.
Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
This avoids issues with some APs rejecting a reassociation if the
station is not currently associated as reported by Yossi Wortzel.
The change is based on a patch from Arik Nemtsov.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an empty IPv4 packet as the keep-alive packet for WNM BSS max idle
period mechanism. This is not really the best possible frame to use for
this, but for now, it can do until a more suitable frame is figured out
for this (e.g., special LLC header to indicate link test purposes).
Signed-hostap: Jouni Malinen <j@w1.fi>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Both EAP-AKA and EAP-AKA' use USIM. Without this change, use of real
USIM card for EAP-AKA' was not allowed to proceed, i.e., only the
software simulated USIM operations were supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.
Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make wpa_supplicant_event() more consistent by not checking
data in either location handling EVENT_RX_MGMT events. This event
is required to specify the data so this pointer cannot be NULL.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d43d37ff2 broke EVENT_RX_MGMT
processing in wpa_supplicant AP mode. ap_mgmt_rx() needs to be called
for Probe Request frames even if they get notified through the new
D-Bus signal mechanism.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit 6bf731e8ce broke handling of
EVENT_CHANNEL_LIST_CHANGED by introducing a cached copy of the driver
channel list that does not get updated even if driver changes its list.
Fix this by synchronizing the cacched wpa_s->hw.modes information
whenever EVENT_CHANNEL_LIST_CHANGED is processed. This fixes P2P channel
list updates based on regulatory domain hints that may trigger driver to
change its supported channel list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When wpa_supplicant disconnects, e.g., due to authentication timeout,
we need to go through the EVENT_DISASSOC/DEAUTH processing similarly
to the driver triggered cases to get correct events delivered to the
ctrl_iface. Fix this by calling wpa_supplicant_event() in these cases
and by filtering out the confusing CTRL-EVENT-DISCONNECTED event with
all zeros BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to disable wpa_supplicant controlled roaming. It should
be noted that the WPA_DRIVER_FLAGS_BSS_SELECTION capability is the
preferred way for this and CONFIG_NO_ROAMING should be obsoleted once
drivers support the new NL80211_ATTR_ROAM_SUPPORT capability
advertisement.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This makes WPA_INTERFACE_DISABLED more consistent in indicating that
wpa_supplicant cannot currently control the interface regardless of
whether the interface is disabled or completely removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This fixes a build regression from commit
cd2f4ddfb9 by moving
wpa_supplicant_assoc_update_ie() outside the no-scan-processing ifdef
block.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.
In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch fixes an issue with roaming for drivers that set
WPA_DRIVER_FLAGS_BSS_SELECTION (currently ath6kl). On moving to an AP
with a different BSSID, an EVENT_ASSOC is received and the subsequent
4-way handshake may fail because of a mismatch between the RSN IE in
message 3/4 and in Beacon/Probe Response. This happens only when the APs
use different RSN IE contents and ap_scan is set to 1, since
wpa_supplicant fails to update its cached IEs.
Initial association may fail, too, in case of multiple APs with
the same SSID, since BSSID selection is done by the driver and again
a mismatch could be seen.
Fix these two issues by clearing and updating the cached IEs on
receiving an Association event from the driver. Also, retrieve the
scan results when the new BSS information is not present locally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP disconnects us with a reason code that indicates that it has
dropped the association, but could allow us to connect again, try to
reconnect to the same BSS without going through the full scan. This can
save quite a bit of time in some common use cases, e.g., when inactivity
timeout is used on the AP (and especially, when waking up from suspend
which has likely triggered some timeout on the AP).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the MAC address of the interface to be changed when the
interface is set down even if the interface does not get completed
removed and re-added.
Signed-hostap: Jouni Malinen <j@w1.fi>
