Since wpa_supplicant is now retrying GAS comeback failures once, the
gas_anqp_oom_hapd test case started failing. Fix this by updating the
test case to expect success (on the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is in preparation of a wpa_supplicant change to allow GAS retries
which can result in the previous test case design showing failures due
to "unexpected" management frames (GAS Initial Request from the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some more test coverage for phase1 parameters that had not
previously been included in any of the test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases were supposed to clear the cfg80211 and wpa_supplicant
scan caches in the end to avoid causing issues to the following test
cases. This did not work properly after introduction of the support for
aborting a pending scan. Fix this by using the flush_scan_cache()
function and waiting within the test case until the final scan operation
completes.
This issue was triggered by ssid_hidden/ssid_hidden2 followed by
ext_password_interworking (though, not every time).
Signed-off-by: Jouni Malinen <j@w1.fi>
The rfkill initialization will be moved out from
wpa_driver_nl80211_drv_init() which would break one step in this OOM
test case due to the memory allocation not existing anymore. Fix this by
skipping that OOM step to avoid causing false failures with the
following commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
This speeds up and clarifies error reporting for cases where the GO
fails to start in invitation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for testing CRDA since it means you can use EPATH to
redirect the test scripts to a different crda binary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds more coverage for TDLS testing for a case where the direct
link should use various VHT channel bandwidths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The decrypted copy of a GTK from EAPOL-Key is cleared from memory only
after having sent out CTRL-EVENT-CONNECTED. As such, there was a race
condition on the test case reading the wpa_supplicant process memory
after the connection. This was unlikely to occur due to the one second
sleep, but even with that, it would be at least theorically possible to
hit this race under heavy load (e.g., when using large number of VMs to
run parallel testing). Avoid this by running a PING command to make sure
wpa_supplicant has returned to eloop before reading the process memory.
This should make it less likely to report false positives on GTK being
found in memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to see where in memory the key was found and what
there is in memory around that location.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
init=CORE was previously used due to invalid db.txt data for 00. For
now, allow both it and the new init=USER after fixed db.txt.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case could fail if the cfg80211 scan cache brought in a BSS
entry from an earlier test case and a new scan did not get executed
prior to the ROAM command. Fix this by forcing the scan to go through
prior to roaming to AP2
This issue showed up with the following test case sequence:
connect_cmd_roam pmksa_cache_opportunistic_connect
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like it is possible for the GTK to be found from memory every
now and then. This makes these test cases fail. Write the memory
addresses in which the GTK was found to the log to make it somewhat
easier to try to figure out where the key can be left in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the BSSs object property change signal to be
generated during the OOM test case for Get(). If that happened, the
signal was not sent out, but the following Get(BSSs) operation succeeded
unexpectedly which resulted in a test failure. Make this less likely to
happen by waiting 50 ms between the scan and Get(BSSs) operation. This
should be sufficient to cover most cases since wpa_supplicant uses 5 ms
timeout for D-Bus property changed updates.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the AP's Beacon frame to be seen by dev[0] when
running a scan. This is not an error case. Make this test case more
robust by verifying with a sniffer whether a Probe Response frame was
sent to unexpected STA.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies client private key use in encrypted PKCS #8 format with
PKCS #5 v1.5 format using pbeWithMD5AndDES-CBC and PKCS #5 v2.0 format
using PBES2 with des-ede3-cbc.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that P2P_CANCEL gets rejected on fully re-invoked persistent
group. This did not work properly before the last couple of commits and
before this week, the P2P_CANCEL on a separate group interface in P2p
Client role could result in use of freed memory and process termination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a cached scan entry in cfg80211 from an earlier test
case to show up while verifying that the disabled AP does not show up in
scan results. This could result in invalid test failures, e.g., when
running test cases "ap_require_ht ap_multi_bss_config" multiple times
(depends a bit on timing). Make this less likely to occur by explicitly
clearing the scan cache and by stopping wlan1 from trying to associate
before stopping ap_required_ht* test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only one of the ERs was stopped at the end of the test case and this
could result in the following test case failing, e.g., when executing
this test case sequence: ap_wps_er_multi_add_enrollee ap_wps_upnp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
