time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test the hostapd venue_url configuration parameter. In addition, fix the
previous defined gas_anqp_venue_url test case to use correct encoding of
the Venue URL ANQP-element payload (URLs were missing and Venue Number
was off-by-one).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case uses EAP-MSCHAPv2 within the PEAP tunnel, so verify that
the build includes support for that before running the test.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
Enable appropriate Suite B test cases with BoringSSL. Currently, this
means enabling only the 192-bit level ECDSA and ECDHE-RSA since
BoringSSL has removed support for DHE and there is no need to support
128-bit level ECDSA anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
On Fedora 26, start.sh fails with these error messages.
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
...
This is because Fedora 26 uses "wheel" group as administrative group.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is used in the tests, too, and was already covered by the build.sh
script, but not this README file.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Clear the model_name parameter back to the default (empty string) at the
beginning and the end of dbus_set_global_properties to avoid failures if
the test case is run multiple times.
Signed-off-by: Jouni Malinen <j@w1.fi>
Ignore any unexpected deviceLost event before the peer devices has been
discovered. This works around issues where the previous test case
terminates before the D-Bus events have been fully delivered. This could
happen, e.g., when running dbus_p2p_discovery twice in a row.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for the configuration exchange to complete before issuing the
DPP_STOP_LISTEN command to avoid confusing sequence of operation between
the ongoing and immediately following DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix bssid2 value to make scanning more reliable for the second OWE BSS.
In addition, reorder the STA status checks to happen before the data
connectivity check to get more accurate failure reason into the log if
the test case fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux kernel commit c9491367b759 ("mac80211: always update the PM state
of a peer on MGMT / DATA frames") enforces the AP to check only
mgmt/data frames PM bit, and to update station's power save accordingly.
When sending only a PS-Poll (control frame) the AP will ignore the PM
bit. As the result, the partial virtual bitmap will not be updated, and
the test ap_open_disconnect_in_ps will fail on tshark check. Since the
test needs only the TIM to be updated, setting PS enabled will send NDP
that will signal that the station is sleeping. Sending PS-Poll to enable
power save is not correct, according to the following standard
statement: "A PS-Poll frame exchange does not necessarily result in an
Ack frame from the AP, so a non-AP STA cannot change power management
mode using a PS-Poll frame."
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This does not really work with mac80211_hwsim due to missing offload
support, but at least some minimal extra code coverage can be achieved.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it a bit clearer to see which parameters need to be modified
if the test vector needs to be recreated based on new values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that PMF can be marked required OWE networks and verify that a
station in transition mode can connect to an open network.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected 2048-bit RSA client certificate gets rejected by
the RADIUS server if the server is configured to use Suite B at 192-bit
level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected p256 client certificate gets rejected if the
server is configured to use Suite B at 192-bit level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PMF is supposed to be enabled automatically in sigma_dut, so remove
the explicit argument to do so from the commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
