Align MSCS response handling as described in IEEE P802.11-REVme/D4.0,
11.25.3 (MSCS procedures):
AP may send unsolicited MSCS Response frame using dialog_token == 0.
Instead of dropping the frame due to dialog_token mismatch, accept
it and set the status accordingly.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Align MSCS response handling as described in IEEE P802.11-REVme/D4.0,
11.25.3 (MSCS procedures):
If an MSCS Descriptor element is present in a MSCS Response
frame that does not indicate a status of "SUCCESS", the request
type field is set to "change" - the element indicates a suggested
set of parameters that could be accepted by the AP in response to a
subsequent request by the non-AP STA.
Handle both MSCS Response frame and (Re)Association Response frame with
change request by extending WPA_EVENT_MSCS_RESULT with the change
values.
Note: since we extend MSCS_RESULT event, move the original event from
both MSCS Response frame and (Re)Association Response frame handlers to
a common function that handles now both 'change' and other response.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
This was done with spatch using the following semantic patch and minor
manual edits to clean up coding style and avoid compiler warnings in
driver_wext.c:
@@
expression a,b;
@@
- os_memcmp(a, b, ETH_ALEN) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- os_memcmp(a, b, ETH_ALEN) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !os_memcmp(a, b, ETH_ALEN)
+ ether_addr_equal(a, b)
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix build of wpa_supplicant if bgscan_simple is enabled while
WNM is not, as in the defconfig.
Fixes: ceb7f65dcc ("bgscan: Allow simple bgscan to do BTM queries")
Signed-off-by: Chien Wong <m@xv97.com>
As otherwise the mld_link_id would be 0, which the driver would
consider a valid link id and would return an error.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
We should be grabbing the include directory using pkg-config and not
just the libs. Without this, the header file might not be found on all
systems because it may not be in /usr/include but elsewhere in the
system.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
_FORTIFY_SOURCE requires at least -O2 optimization level.
This may result in compilation warnings. Fix it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
cfg80211 requires the link ID to be specified for requests to start a
remain-on-channel operation during an ML association. This feels wrong
since the ROC operation is in most cases unrelated to the
association. However, that requirement has been in place since kernel
commit 7b0a0e3c3a88 ("wifi: cfg80211: do some rework towards MLO link
APIs") from April 2022, and as such, it looks necessary to have
wpa_supplicant work around this by specifying the currently used link ID
that would seem to match the ROC channel most closely.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The GAS request may have been issued using a link address of the AP
MLD's affiliated link and the driver may translate that address to the
MLD MAC address when associated with the AP MLD. Accept GAS responses
where the addresses map to the same AP MLD.
Signed-off-by: Jouni Malinen <j@w1.fi>
The target MAC address needs to be checked against all the AP MLD link
addresses and the MLD MAC address to cover all possible cases. This is
needed to be able to correctly use Protected Dual of Public Action
frames during an ML association.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current operating channel bandwidth in an HE BSS is determined with
the combination of elements, include the VHT Operation element. Use VHT
Operation element to check whether the 80, 80+80, and 160 MHz cases are
enabled if the AP claims to be capable of operating an 80/160 MHz BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current operating channel bandwidth in an HE BSS is determined with
the combination of elements, include the HT Operation element. Use HT
Operation element to check whether the 40 MHz case is enabled if the AP
claims to be capable of operating a 40 MHz BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the PHY parameters from configuration or the values passed in from
the dbus API for P2P dbus command GroupAdd instead of using the hard
coded values to be inline with the method provided with the
wpa_supplicant control interface.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
The vht_center_freq2 parameter was in incorrect order in the call to
wpas_p2p_group_add_persistent(). This would have dropped the value when
adding a group based on a previously created persistent group ion the GO
side and that would have resulted in a failure to start the GO.
Fix the function call to use the correct order for the parameters.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
This allows the function to be used outside the context of the
wpa_supplicant control interface implementation.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
When the P2P persistent group is provisioned out-of-band, i.e., add
persistent group with a known BSSID, SSID, passphrase, and frequency,
and start the group with GroupAdd dbus command, the group info fetched
on the cliend side has zero MAC address for BSSID and no value for
frequency. Fix this issue by getting that information from
wpa_s->current_bss instead of wpa_s->go_params.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
The location of the comment is incorrect and it is not really needed.
Remove it.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We only print the newline if the AP MLD ID is present
(BASIC_MULTI_LINK_CTRL_PRES_AP_MLD_ID), fix that.
Fixes: e3e68668c1 ("ctrl_iface: Report RNR and ML in BSS command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
It is not really helpful to get debug prints about Hotspot 2.0 frame
filtering when trying to connect a non-Hotspot 2.0 network. Remove this
debug print that was being printed for every connection that did not use
Hotspot 2.0.
Signed-off-by: Jouni Malinen <j@w1.fi>
An affiliated AP of an AP MLD can temporarily be disabled. Other
affiliated APs of the AP MLD indicate this in the Reduced Neighbor
Report (RNR) elements added to their Beacon and Probe Response frames.
When an affiliated AP is disabled, it should be included in the
association exchange, but can be activated only after it is enabled.
Add support identifying disabled APs and propagate the information
to the driver within the associate() callback.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Don't ever return -1 from print_bss_info() as that causes
corruption of the output.
Also don't return -1 from print_fils_indication() as that
would stop the iteration over all BSSs.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is needed to work around some issues that show up mainly in testing
scenarios when the same BSSID might be used with different
configurations and the scan results from the driver might include both
the old and new contents when two different SSIDs are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use AP MLD address instead of BSSID for PWE derivation during MLO
connection. This was already done for H2E in commit e869fdfeef
("wpa_supplicant: Use MLD address in SAE authentication"). While IEEE
P802.11be requires H2E to be used, there are deployed AP MLDs that do
not follow that requirement. This change to the hunting-and-pecking loop
case is needed for interoperability workarounds with such APs.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
During scan results matching for connection skip BSS entries for the
current connection if disassociation imminent is set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Instead of rejecting the request, accept it since the AP MLD is in
control of which links are available and we are not being fully
disconnected in this case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Based on IEEE P802.11be/D5.0, when a station is non-AP MLD with more
than one link the combination of the Link Removal Imminent field set to
1 and the BSS Termination Included field set to 1 means than only one of
the links is removed while the other links will remains associated.
Handle this case without starting a scan to find another BSS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow frames where the SA is the AP MLD MAC address as the driver might
have performed address translation.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For wpa_supplicant based SAE/OWE connection, the wpa_supplicant state
machine is aware of the PMKID created for a connection and this gets
removed when "REMOVE_NETWORK all" is called. However, when SAE/OWE
offload is enabled, wpa_supplicant is not aware of the PMKID generated
by the driver/firmware. So add PMKSA del indication to the driver from
remove_network context so that the driver can free PMKs associated with
the SSID.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The bgscan_init() declared wrongly when CONFIG_BGSCAN is not defined,
fix that.
Fixes: 3139270903 ("bgscan: Add global bgscan configuration")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Otherwise any new scan result (even manual ones if they do not set
use_id=X to a non-zero value), can cause a reconnect to the same BSS
when MLO is used. This is because the current BSS is not detected by
wpa_supplicant_need_to_roam() and it assumes that roaming is needed.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Earlier refactoring of ibss_mesh_setup_freq() ended up dropping the case
where HE would be enabled without VHT on the 2.4 GHz band. Add that back
to allow HE to be used on 2.4 GHz with IBSS and mesh.
Fixes: 64043e6156 ("Split ibss_mesh_setup_freq() into multiple functions")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Link ID needs to be specified for MLD case when doing channel switch.
Add it to the driver command.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Allow doing X BSS transition management query calls before falling back
to scan.
Example format to do 4 BTM queries before attempting a scan:
bgscan="simple:30:-65:300:4"
Signed-off-by: Ben Greear <greearb@candelatech.com>
On the default configuration if MBO only is enabled then build breaks as GAS
is not selected, if other features that auto-enable GAS are selected
then it works.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
For a memory constrained system, it may be more important to reduce
binary size than include support for these capabilities.
By default this is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
For a memory constrained system, it may be more important to reduce
binary size than include support for these capabilities.
By default this is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Removing radio measurements and supported operating class indication
might be needed to reduce binary size for a memory constrained system
that does not need more advanced features. However, removing these is
not recommended since they can help the AP manage the network and STA
steering.
By default this functionality is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Beacon hinting is a feature that can temporarily change the regulatory
rule flags on the channel where the radio hears the beacon. Add a new
event CTRL-EVENT-REGDOM-BEACON-HINT to notify the wpa_supplicant user
about an important update to the regulatory rules including which
frequencies are impacted, new power limit, and new rule flags.
Signed-off-by: Jun Yu <junyuu@chromium.org>
The wpa_auth_callbacks for mesh was missing a for_each_sta
implementation. This is an issue with pmksa cache, as when a cache entry
expires the for_each_sta callback is called in order to clear the pmksa
reference for all sta that was using this entry. Not having a
for_each_sta callback will prevent this cleanup to happen then a sta
could still use this pmksa entry even after it has been freed.
This used after free was not a problem up until recently where
dpp_pkhash is now stored in pmksa entry and retreived later on causing
crash with below backtrace:
_wpa_snprintf_hex src/utils/common.c:326
wpa_snprintf_hex src/utils/common.c:348
hostapd_ctrl_iface_sta_mib src/ap/ctrl_iface_ap.c:542
hostapd_ctrl_iface_sta_mib src/ap/ctrl_iface_ap.c:542
hostapd_ctrl_iface_sta_mib src/ap/ctrl_iface_ap.c:600
hostapd_ctrl_iface_sta src/ap/ctrl_iface_ap.c:615
wpa_supplicant_ctrl_iface_process src/wpa_supplicant/ctrl_iface.c:12741
wpa_supplicant_global_ctrl_iface_receive src/wpa_supplicant/ctrl_iface_unix.c:1141
eloop_sock_table_dispatch src/utils/eloop.c:625
eloop_run src/utils/eloop.c:1238
wpa_supplicant_run src/wpa_supplicant/wpa_supplicant.c:8021
main src/wpa_supplicant/main.c:393
Adding a for_each_sta callbacks fixes that.
Fixes: 043dedee83 ("DPP: Expose enrollee pubkey hash for identification")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
The length of the PMK ended up getting lost when a PMKSA cache entry was
added based on externally managed information. Set the PMK length in SAE
context to get the correct length stored into the actual PMKSA cache
entry that gets created in this path.
Signed-off-by: Jouni Malinen <j@w1.fi>
nl80211_set_secure_ranging_ctx() was already ignoring the operation, but
this is included only with CONFIG_DRIVER_NL80211_QCA=y. Make the default
case use same behavior based on the callback function not being defined.
This is needed to allow the following test cases to work:
pasn_owe_tm_kdk_secure_ltf pasn_sae_kdk_secure_ltf
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move the hostapd and wpa_supplicant control interface handlers into a
shared functions instead of duplicated implementation.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When connecting, pending_bssid is set to the main link that we are
authenticating/associating on. Later on, the MLD MAC address will be
stored in the bssid, but we may also try to deauthenticate before we are
connected and in that case, pending_bssid is not yet set to the MLD MAC
address.
As such, use the ap_mld_addr instead of pending_bssid if n_mld_links is
non-zero. This is the sensible thing to do and expected behavior on
nl80211.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This improves chances with APs that do not reply to Probe Request frame
with short SSID or with direct BSSID.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
According to IEEE P802.11be/D4.0, 35.3.4.2, the AP MLD ID must be
included in the Probe Request ML element in case it is sent to a
transmitted BSS in which case it should be set to 0. If it is sent to an
non-transmitted BSSID, the AP MLD ID should not be included.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If for some reason association fails and a link which has an error is
reported, add that specific link to the ignore list. After that,
immediately retrigger the connection code. In the usual case, we are
then going to reconnect to the same AP MLD but with that particular link
not being included in the connection.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This avoids, e.g., trying to use a BSS that is rejected by mac80211 as a
link, which could fail the connection as a whole.
Note that this is not perfect. Ideally, the internal state would have a
more context sensitive ignore flag so that one could still use a BSS as
a link in some situation.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Parse the link status values out of Multi-Link association response. If
the AP rejects ML association and marks the links as failed with a
reason code other than TX_LINK_NOT_ACCEPTED, also report these links to
wpas_connection_failed() and ignore them.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Parsing multiple RNR elements already exists in
wpa_bss_parse_basic_ml_element(), so wpas_ml_element() just duplicates
the same code. Combine the functionality of both these functions and
remove the duplicate.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add band preference, BSSID preference, and single link enforcement
testing options. This is needed for testing MLO.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The current set of global configuration fields is getting close to the
previously used 15000 byte limit, so increase this size to 16000 and add
a note about the potential need to change this size when adding new
fields.
Signed-off-by: Jouni Malinen <j@w1.fi>
Three functions were provided for defragmentation. First
ieee802_11_defrag(), ieee802_11_defrag_mle() and then
ieee802_11_defrag_data() which would do the actual job. With
ieee802_11_defrag() picking the member in the elements struct for an
EID. The problem with this is, that for the Multi-Link element, there
are multiple entries in the elems struct depending on its type. As such,
remove the intermediate function and simply pass the correct members
directly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This workaround from commit 6d6f4bb87f ("nl80211: Work around mac80211
limitation on (re)auth when authenticated") pre-dates the code that
supresses the deauth or disconnect event from nl80211. Should this code
be called it would not actually work at this point, as important
internal state for the authentication attempt has already been lost.
Simply drop the code. This might also fix issues where we could get
into a bad state if a proper deauth/disconnect event happens while we
are authenticating or associating.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This is needed to avoid NULL pointer deferencing in
wpa_supplicant_ctrl_iface_msg_cb() if any of the functions called from
wpas_bssid_ignore_module_tests_() ends up using wpa_msg().
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Order scan results in a manner that prefers BSSs that support SAE over
ones that support PSK without SAE if the SNR of the SAE BSS is good or
at least at the same level as the SNR for the PSK BSS. This improves
likelihood of using SAE when the local network profile allows
WPA3-Personal transition mode and the ESS uses a mix BSSs with different
sets of AKMs.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the optimization from commit 9c97126576 ("OWE: Optimize
transition mode scan to use known channels") to cover cases where the
STA is configued with OWE transition mode disabled, but the AP uses OWE
transition mode.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
BSS table is not updated when a non-P2P station runs a scan without P2P
IE in Probe Response frame, since that would remove P2P IE information.
However, this results also in not updating mandatory rates in Supported
Rates and BSS Membership Selectors element even though AP/GO changes
frequency from 2.4 GHz to 5 GHz band.
This is causing connection failure since BSS table has 1 Mbps as
mandatory rate for AP connection but minimum supported rate in 5 GHz
band is 6 Mbps.
To avoid connection failures in such cases, don't skip updating BSS
table when the BSS frequency is changed. This covers the most important
case addressed in commit ff57398fca ("P2P: Do not drop P2P IEs from
BSS table on non-P2P scans") while still allowing other changes to be
taken into account if the GO were to actually change channels (or band,
which would be the most likely case needing the update).
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Fix references to the appropriate driver capability drv_flags2. The
initial version used the incorrect drv_flags value and by doing so,
ended up using incorrect driver capabilities (DEAUTH_TX_STATUS,
BSS_SELECT, TDLS_SUPPORT) which could result in incorrect OWE
functionality for both AP and STA cases.
Fixes: d984c7b298 ("hostapd: Add support for OWE offload for STA/AP interface")
Fixes: da364180fb ("hostapd: Support 4-way handshake offload for AP/P2P GO")
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
If the local network profile specifies a specific BSSID, there will not
be an acceptable alternative AP for the current one. As such, there is
not much point in trying to scan and wait for the results to make this
conclusion. Skip the scan and reject the BSS transition management
request even if that ends up getting disassociated from the BSS that
happens the be the only one that the local configuration allows to be
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver advertising OWE offload support would take care of
Diffie-Hellman Parameter element generation and processing part. The
driver would be responsible for OWE PMK generation in this case.
Avoid the Diffie-Hellman Parameter element handling in
wpa_supplicant/hostapd for drivers advertising OWE offload support. This
change is applicable only for drivers supporting 4-way handshake
offload.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Add support for offloaded 4-way handshake in AP/P2P GO mode. For drivers
supporting the AP PSK offload, wpa_supplicant/hostapd passes down the
PSK for the driver to handle the 4-way handshake. The driver is expected
to indicate port authorized event to indicate that the 4-way handshake
is completed successfully.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The max transmit power of Standard Power (SP) Access Points (AP) on
6 GHz band and APs on 2.4 GHz and 5 GHz bands is limited by effective
isotropic radiated power (EIRP), while the max transmit power of Low
Power Indoor (LPI) APs on 6 GHz Band is limited by power spectral
density (PSD). Therefore the max transmit power of LPI APs grows as the
channel width increases, similar to the noise power which has constant
PSD.
Adjust the RSSI, SNR and throughput estimate based on max transmit power
config and max channel width in the roaming algorithm.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
The max transmit power of Standard Power (SP) Access Points (AP) on
6 GHz band and APs on 2.4 GHz and 5 GHz bands is limited by effective
isotropic radiated power (EIRP), while the max transmit power of Low
Power Indoor (LPI) APs on 6 GHz Band is limited by power spectral
density (PSD). Therefore the max transmit power of LPI APs grows as the
channel width increases, similar to the noise power which has constant
PSD.
Adjust the SNR of BSSes based on the transmit power config and max
channel width. EIRP limited APs usually have constant max transmit power
on different channel widths, their SNR decreases on larger channel width
because the noise power is higher, while PSD limited APs have constant
SNR over all channel widths.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
With the SSID updating of a BSS entry removed from owe_trans_ssid(),
this call to owe_trans_ssid() is not really doing anything, so remove
it. This reverts 6972b0fa2b ("OWE: Update transition mode information
on selecting a new BSS").
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Overwriting of SSID for the hidden OWE BSS entry has some side effects:
- first the entry is notified over DBus with empty SSID and the update
of SSID is never signaled (it is not even possible at the moment to
notify the SSID change - see wpas_dbus_bss_signal_prop_changed()),
- during (and after) association there will be multiple entries
referring to the same BSSID/SSID pair.
Stop overwriting the SSID in an existing BSS entry based on OWE
transition mode information. Instead, depend on a new BSS entry getting
added for the hidden OWE BSS based on active scans for the SSID learned
from the open BSS. This would not have been sufficient for the initial
OWE design, but with the optimized scanning behavior from commit
c04562e67e ("OWE: Improve discovery of OWE transition mode AP"), this
can now depend on the exact same mechanism as other uses of hidden
SSIDs. This helps in keeping the D-Bus interface in sync with the BSS
parameters.
Signed-off-by: Andrzej Ostruszka <andrzejo@chromium.org>
If the currently available scan results include OWE transition mode BSS
with an unknown SSID, optimize the following scan for OWE to use only
the channels on which a known transition mode BSS has been seen.
This is needed to be able to remove the design that updates BSS entries
with the learned OWE SSID in manner that does not result in regression
to scanning latencies.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The local network profile may not have matching SSID (it could be either
the wildcard 0-length SSID or visible SSID in case of OWE transition
mode), so check whether an exact match with a BSS entry can be made
using the current SSID information from the driver (i.e., the SSID of
the current association) when picking the BSS entry to use as the
current one for an association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the Same SSID and Colocated AP bits as an alternative way of finding
a match on the current SSID.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The Reduced Neighbor Report element can include one or more TBTT
Information fields. Only the first one was parsed previously. Extend
this to use a loop to go through all included TBTT Information fields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Beacon frames are allowed to optionally include one more more Reduced
Neighbor Report elements. Only the first one was parsed previously.
Extend this to use a loop to go through all included RNR elements.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Leverage the already available control socket cmd "DRIVER_FLAGS2" and
dump the driver capab "flags2" bitmask on triggering the new CLI CMD
"driver_flags2", similar to the already existing CLI CMD "driver_flags".
$ hostapd_cli -i wlan0 driver_flags2
(OR)
$ wpa_cli -i wlan0 driver_flags2
0000000000000020:
BEACON_RATE_HE
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
gcc 12.1 complains about using pointer after realloc as it could
potentially be moved/freed, causing any uses after UB.
Fix this by doing checks before realloc and use those statuses and
update with new BSS.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Prevent loading arbitrary executable code based on config at runtime,
while allowing libraries to be specified at compile time when they are
known in advance.
Add the ability to configure libraries to load at compile time.
* CONFIG_PKCS11_ENGINE_PATH - pkcs11_engine library location.
* CONFIG_PKCS11_MODULE_PATH - pkcs11_module library location.
* CONFIG_OPENSC_ENGINE_PATH - opensc_engine library location.
Add flags with the ability to set each of the libraries to NULL and
prevent loading them at runtime.
* CONFIG_NO_PKCS11_ENGINE_PATH - prevents loading pkcs11_engine
library.
* CONFIG_NO_PKCS11_MODULE_PATH - prevents loading pkcs11_module
library.
* CONFIG_NO_OPENSC_ENGINE_PATH - prevents loading opensc_engine
library.
* CONFIG_NO_LOAD_DYNAMIC_EAP - prevents loading EAP libraries at
runtime.
Signed-off-by: David Ruth <druth@chromium.org>
wpas_dpp_connected() is called from wpa_supplicant_set_state(), i.e.,
from the middle of processing of the post 4-way handshake steps. Sending
a DPP Public Action frame at that point can delay other operations, so
allow those steps to be completed first before sending out the DPP
connection status result.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like mac80211 ROC handling can end up postponing offchannel TX
operation by the previously started and already canceled wait time if
the new NL80211_CMD_FRAME is issued immediately after
NL80211_CMD_FRAME_WAIT_CANCEL. Make this more robust by waiting for the
driver event that indicates completion of the cancel operation (i.e.,
NL80211_CMD_FRAME_WAIT_CANCEL as an event) before issuing
NL80211_CMD_FRAME for another channel. If the driver event is not
received within 10 ms, start the operation anyway to avoid unexpected
behavior if there are drivers that do not end up notifying end of the
wait.
This fixes some issues with authentication initiation for cases where
multiple channels are iterated. This can also significantly speed up
that process.
Signed-off-by: Jouni Malinen <j@w1.fi>
The first event could have theoretically been received with reltime
sec=0, so use the helper function to check whether the reltime value is
actually set so that the usec part is checked as well. This is not going
to have a difference in practice, but it was possible to hit this corner
case with mac80211_hwsim testing (ap_cipher_tkip_countermeasures_sta)
using UML and time travel.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for Authentication negotiated over IEEE Std 802.1X
with key derivation function using SHA-384.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When channel 140 is configured in mesh, interface fails to come up due
to channel bond (136,140). Since Channel 136 is not HT40+ capable,
validation for HT channel bonding fails when it checks whether first
channel in the bond (channel 136) is HT40+ capable.
In mesh, during channel setup, secondary channel offset for the
configured channel will be selected as +1 if primary channel is capable
of HT40+. In current code, channel 140 is not allowed as HT40+ and hence
secondary channel offset is selected as -1, which makes 136 as secondary
channel. But channel 136 is not HT40+ supported and fails in channel
bonding validation.
Add 140 to HT40+ allowed list as HT40+ is supported for the channel.
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Pointer entry->ssid might be passed to owe_trans_ssid_match() function
as argument 3 with NULL value, and it may be dereferenced there. This
looks like a theoretical case that would not be reached in practice, but
anyway, it is better to check entry->ssid != NULL more consistently.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Since wpa_supplicant version 2.10 the extended capabilities MSCS and SCS
are advertised in the (Re)Association Request frames.
This causes the association request to be rejected by several access
points. Issue was observed with:
- D-Link DIR600
- TP-Link AC1900
- Synology MR2200ac
To avoid this issue the extended capabilities MSCS and SCS shall only be
added if the bss also supports them. While this may not follow the exact
behavior described in IEEE 802.11, this is a reasonable compromise to
avoid interoperability issues since these capabilities cannot be used
with an AP that does not support them anyway.
Note: The Extended Capabilities element is only included in the
Association Request frames if the AP also sent its extended capabilities
(see wpas_populate_assoc_ies()) as a workaround for misbehaving APs.
This workaround exists since version 2.1.
Signed-off-by: Sebastian Priebe <sebastian.priebe@konplan.com>
There is a delay between sending Association Response frame after having
received Association Request frame, due to the fact that between
receiving the request and sending the response the Beacon frame contents
is updated, after analyzing inputs from the STA. There may be several
updates if multiple fields need to change. This can cause issues with
some devices in noisy environments with many BSSs and connected STAs.
Optimize this by updating the beacon only once, even if there are
multiple reasons for updates.
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
Drivers will often report regdom changes in the middle of a scan if they
detect during that scan that the regulatory domain has changed. If this
happens and we enter a regdom that supports 6 GHz channels when the
previous one didn't (this often happens in 6 GHz-capable regdoms for
devices after suspend/resume), immediately trigger a 6 GHz-only scan if
we were not able to connect to an AP on a legacy band.
This should significantly improve connection time to 6 GHz AP after
regdom has been reset.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Store 6 GHz capability on channel list update for wpa_supplicant use.
This will be used in the next commit to extend scanning behavior based
on changes to 6 GHz channel availability.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
wpa_supplicant_trigger_scan() previously wouldn't include any of the IEs
generated by wpa_supplicant_extra_ies(). Instruct it to do so in most
cases. This is necessary because MBO STAs are required to include MBO
capabilities in their Probe Request frames.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
After GO negotiation is completed, the P2P Client needs to scan the GO
before connecting. Only SSID was specified for this and the driver still
might need to scan all channels which wastes time. wpa_supplicant can
pass the known BSSID in the scan request in additional P2P cases and
this allows the driver sto stop the scan once the specific BSSID is
found. This helps reduce some time for P2P connection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Handler function for "Scan" method call of a network device doesn't set
non_coloc_6ghz, therefore wpa_supplicant doesn't scan non-PSC channels
on 6GHz band only if a co-located AP was reported on the channel.
Add NonColoc6GHz and 6GHzOnly flags to the wpas_dbus_handler_scan, so
that dBus scan requests can cover non-PSC channels and scan only 6 GHz
channels.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
Parse the reconfiguration Multi-Link element and:
- Don't select a BSS for connection if it is part of an MLD
and is going to be removed.
- Don't scan for missing links that are to be removed.
- Don't include removed links in association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a control interface to trigger ML probes for testing purposes.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for building and sending ML probe requests. During connect,
try to send an ML probe request if we are going to connect to an MLD AP
and the BSS information for some of the links is missing.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extend 'struct wpa_driver_scan_params' to allow higher layer to indicate
if minimal probe request content should be included by the driver as part
of the scan logic.
Implement this with driver_nl80211, by setting
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use the wpas_notify_mesh_peer_*() functions for sending the control
interface events in addition to the D-Bus events so that these are all
done consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using mesh we have incoherent
MESH-PEER-CONNECTED/MESH-PEER-DISCONNECTED messages when we restart one
of the devices without disconnecting it first. Sometimes we have the
right behavior, a peer disconnect and then a peer connect, sometimes we
only have a a peer connected without a peer disconnected first, and
sometimes we have nothing at all.
As the plink count seem to be correctly tracked and because we only send
the connected event on plink count increase, lets send the peer
disconnected event on plink count decrease.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
When using wpa_supplicant to connect to a mesh network or to create an
AP, the current code doesn't respect all CONFIG_XXX_OVERRIDES network
parameters, just disable_ht in CONFIG_HT_OVERRIDES.
Add support for some of the others modulation related disable flags:
- disable_ht40 with CONFIG_HT_OVERRIDES
- disable_vht with CONFIG_VHT_OVERRIDES
- disable_he with CONFIG_HE_OVERRIDES
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
This should allow STA to make better choice about which BSS to roam to.
Use estimated throughput as comparison value. Can improve the estimated
throughput calculation to improve this selection criteria if wanted in
the future.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Along with canceling queued scan, abort ongoing scan if any, this
ensures Wi-Fi interface is in usable state after disconnect is issued,
else subsequent scan after disconnect might fail with EBUSY.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If the current AP advertises disassociation imminent, move it to the
back of the candidate list so we don't select it again while other
candidates are available.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Some kind of race condition seemed to be hit at least in test sequence
"p2p_ext_vendor_elem_invitation pasn_comeback_after_0_sae" where the P2P
invitation response could have been received just after having scheduled
a new p2p-listen radio work, but before that work had been started. In
the case of accepted invitation, this could result in unnecessary extra
delay when that p2p-listen work ended up getting started at the exact
time that the local device was starting GO.
Avoid this race condition by removing the pending p2p-listen radio work
when P2P listen is stopped.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant underestimates 6 GHz SNR as it assumes 2 GHz default
noise in the estimation.
Use 6 GHz default noise when estimating 6 GHz SNR.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
It doesn't make sense to disconnect on updates to the
network's scan_freq, and in fact doing so causes some
(timing-/scheduling-dependent) test failures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wpa_supplicant postpones expired PMKSA deletion untillassociation is
lost for SAE to avoid forced disconnection. But during this time the
driver may use the expired PMKSA for reassociation with the current
connected AP.
Remove the current PMKSA for SAE from the driver after reauth threshold
is passed when the driver takes care of BSS selection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Do not reject reauth threshold passed PMKSA indicated in successful
association event since the PMKSA is still valid.
Additionally, remove the reauth threshold passed PMKSA entry from the
driver to prevent using it further in the driver.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add the copied EHT capabilities into the sta_add() call when adding a
TDLS peer.
The mld_link_id value was previously only for AP mode, but it can now be
used for TDLS links as well to indicate the link on which a
single-link-TDLS direct link is negotiated.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to be able to determine which link is used for TDLS setup
when the current association is with an AP MLD.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to allow the driver to know on which operating channel
(as specified by the link that is affiliated with AP MLD for the current
association) is used for transmitting TDLS Discovery Response. This
commit adds the link_id parameter to various functions, but does not
implement the driver interface change itself.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
Commit 9025def55c ("wpa_supplicant: Add support for pregenerated MAC")
added this capability, but did not update wpa_supplicant.conf to
document it. Add such documentation to match the information in
config_ssid.h.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The ap_mld_addr entry was added without introducing a new mask bit which
does not follow the expected style for adding new information into the
BSS command and might result in unexpected behavior for external
components. Define a new BSS command information mask bit for this AP
MLD address and print the AP MLD address in the BSS info only if the
mask bit is set.
Fixes: db99e7341a ("Add AP MLD address into BSS command output")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Send the actual MFP configuration value to the driver instead of
overriding it with MFP required based on the wpa_supplicant selected BSS
when the driver takes care of BSS selection.
This is needed to allow the driver to know whether it can select an MFP
disabled BSS.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), enable
support for the following optional QoS Characteristics parameters:
- Maximum MSDU Size
- Service Start Time
- Service Start Time LinkID
- Mean Data Rate
- Delayed Bounded Burst Size
- MSDU Lifetime
- MSDU Delivery Info
- Medium Time
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add support to configure the mandatory QoS Characteristics parameters
per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), in SCS
request:
- Minimum Service Interval
- Maximum Service Interval
- Minimum Data Rate
- Delay Bound
Enable STA SCS traffic descriptor support for EHT connection when the
connected EHT AP advertises SCS traffic descriptor capability in the EHT
Capabilities element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Set WFA capability to allow non-EHT SCS Traffic support in association
elements when the AP advertises support for non-EHT SCS Traffic support
via Beacon or Probe Response frame. This capability is upper layer
functionality and as such, does not need a separate driver capability
indication or configuration, but indicate this only if the AP supports
the feature to minimize risk of interoperability issues with a new
information element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
wpa_drv_get_pref_freq_list() may fail and the 6 GHz channel removal
should not be done unless the operation actually succeeded. The previous
implementation ended up processing uninitialized data. This did not
really result in any observable misbehavior since the result was not
used, but this showed up as a failed test case when running tests with
valgrind.
Fixes: f0cdacacb3 ("P2P: Allow connection on 6 GHz channels if requested")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant could crash due to dereferencing freed memory in a corner
case. When a reestablished P2P GO group gets removed because the
hardware mode is not supported when switching from 2.4 to 5 GHz. Group
removal in wpas_p2p_group_delete() forget to clean wpa_s->last_ssid due
to the missing wpas_notify_network_removed() call before removing the
network with wpa_config_remove_network().
That could cause a crash when flushing old BSSs which age out in
wpa_bss_flush_by_age() which uses wpa_s->last_ssid in some cases.
Fix this by invoking wpas_notify_network_removed() to clean
wpa_s->last_ssid when removing a temporary P2P group network.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In the original flow, after hostapd_config_tx_queue() successfully
parses a tx_queue variable, wpa_config_process_global() would not return
immediately. Then it would print out "unknown global field" later and set
return val to -1.
Return success (0) after hostapd_config_tx_queue() successfully parses a
tx_queue variable to fix this.
Fixes: 790026c3da ("Allow TX queue parameters to be configured for wpa_supplicant AP/P2P GO")
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
Fix the warning:
wpa_supplicant.c:2257:5: warning: conflicting types for
‘wpas_update_random_addr’ due to enum/integer mismatch; have ‘int(struct
wpa_supplicant *, enum wpas_mac_addr_style, struct wpa_ssid *)’
[-Wenum-int-mismatch]
2257 | int wpas_update_random_addr(struct wpa_supplicant *wpa_s,
| ^~~~~~~~~~~~~~~~~~~~~~~
In file included from wpa_supplicant.c:32:
wpa_supplicant_i.h:1653:5: note: previous declaration of
‘wpas_update_random_addr’ with type ‘int(struct wpa_supplicant *, int,
struct wpa_ssid *)’
1653 | int wpas_update_random_addr(struct wpa_supplicant *wpa_s, int
style,
| ^~~~~~~~~~~~~~~~~~~~~~~
Fixes: 1d4027fdbe ("Make random MAC address style parameters use common enum values")
Signed-off-by: Chien Wong <m@xv97.com>
Parse link id and station MLD address received from the driver in the
NL80211_CMD_NEW_STA event.
Set MLO information of the station to the sta_info and wpa_sm.
Co-authored-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Set the sme RRM used config if the RRM element is present in the
(Re)Association Request frame sent in association event to cover the
cases where the driver SME takes care of negotiating RRM capabilities.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previous PEAP client behavior allowed the server to skip Phase 2
authentication with the expectation that the server was authenticated
during Phase 1 through TLS server certificate validation. Various PEAP
specifications are not exactly clear on what the behavior on this front
is supposed to be and as such, this ended up being more flexible than
the TTLS/FAST/TEAP cases. However, this is not really ideal when
unfortunately common misconfiguration of PEAP is used in deployed
devices where the server trust root (ca_cert) is not configured or the
user has an easy option for allowing this validation step to be skipped.
Change the default PEAP client behavior to be to require Phase 2
authentication to be successfully completed for cases where TLS session
resumption is not used and the client certificate has not been
configured. Those two exceptions are the main cases where a deployed
authentication server might skip Phase 2 and as such, where a more
strict default behavior could result in undesired interoperability
issues. Requiring Phase 2 authentication will end up disabling TLS
session resumption automatically to avoid interoperability issues.
Allow Phase 2 authentication behavior to be configured with a new phase1
configuration parameter option:
'phase2_auth' option can be used to control Phase 2 (i.e., within TLS
tunnel) behavior for PEAP:
* 0 = do not require Phase 2 authentication
* 1 = require Phase 2 authentication when client certificate
(private_key/client_cert) is no used and TLS session resumption was
not used (default)
* 2 = require Phase 2 authentication in all cases
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to match the key configuration design with a single
netdev and the nl80211 driver interface.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
EAPOL frames may need to be transmitted from the link address and not
MLD address. For example, in case of authentication between AP MLD and
legacy STA. Add link_id parameter to EAPOL send APIs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed for the driver to know on which link it should transmit
the frames in MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This includes:
- Modifications of the driver API, to include the link ID as part
of 'struct hostapd_freq_params'.
- Modifications to nl80211 driver.
- Modifications for the driver wrappers.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support to indicate link reconfiguration event reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to indicate TID-to-link mapping changes reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The Linux kernel expects to use the AP MLD address in
NL80211_ATTR_PREV_BSSID for reassociation requests when the current
association is MLO capable.
Previously, wpa_supplicant was using the BSSID value in
NL80211_ATTR_PREV_BSSID even if the connection is MLO capable. Fix this
by sending the AP MLD address in NL80211_ATTR_PREV_BSSID for
reassociation requests when MLO is used.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
In some cases like unknown-group rejection, AP MLD can't parse the
received Authentication frame to the point of the Multi-Link element if
the group used by the peer is unknown to the AP MLD.
In such cases, AP MLD not including Multi-Link element in rejection
Authentication frames can be considered as standard compliant since AP
MLD doesn't know whether the received Authentication frame has
Multi-Link element or not.
To avoid connection issues in such cases, don't reject Authentication
frames without Multi-Link element when status code is other than
WLAN_STATUS_SUCCESS, WLAN_STATUS_SAE_HASH_TO_ELEMENT,
WLAN_STATUS_SAE_PK, and WLAN_STATUS_ANTI_CLOGGING_TOKEN_REQ.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
When starting a new BSS as AP mode, the network configs have been passed
in from the BSS config. There is no need to scan before creating a new
BSS. Reuse connect_without_scan structure member to bypass scan when the
mode is WPAS_MODE_AP.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
If IEEE8021X_EAPOL is not defined wpa_supplicant will not compile with
following error:
events.c: In function 'wpa_supplicant_connect':
events.c:1827:14: warning: implicit declaration of function 'eap_is_wps_pbc_enrollee' [-Wimplicit-function-declaration]
1827 | if ((eap_is_wps_pbc_enrollee(&ssid->eap) &&
| ^~~~~~~~~~~~~~~~~~~~~~~
events.c:1827:43: error: 'struct wpa_ssid' has no member named 'eap'
1827 | if ((eap_is_wps_pbc_enrollee(&ssid->eap) &&
| ^~
Add ifdef statements around the calling function to fix the issue.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Some of the information elements added in IEEE Std 802.11ax-2013 for VHT
purposes have since then been taken into use for other cases and renamed
to remove the "VHT" prefix in the standard. Update the defines for those
elements in the implementation to match the names used in the current
standard.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant was skipping MLD APs from network selection when the AP
advertise legacy open, WPA2-Personal-only (PSK without SAE), or PMF
disabled. However, there are already some early Wi-Fi 7 APs in the
market which advertise legacy open, WPA2-Personal-only, or PMF disabled
even though these combinations are unlikely to be allowed for Wi-Fi 7 in
the end.
To avoid connectivity issues with such APs, allow stations to connect
with MLO disabled when an AP MLD is detected to advertise legacy open,
WPA2-Personal-only (PSK without SAE), or PMF disabled.
This reverts commit 7d8b96dcfd ("wpa_supplicant: Apply same
restrictions for MLD as for 6 GHz BSS") except WEP and TKIP checks,
i.e., AP MLDs which advertise only WEP or TKIP are still skipped from
network selection.
For the SME-in-wpa_supplicant case, skip configuring MLD parameters to
the driver if the STA can connect only in legacy open,
WPA2-Personal-only, or PMF disabled mode. For the SME-in-driver case, it
is the driver's responsibility to initiate connection with MLO disabled
with such APs.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The driver-initiated BSS selection case and the "Network configuration
found for the current AP" case ended up clearing the RSN state machine
information on AP RSNE/RSNXE. That could result in incorrect behavior if
some key management operations depended on accurate information. For
example, this could result in not deriving the KDK as part of the PTK
derivation and failing to complete 4-way handshake if both the AP and
the STA indicated support for Secure LTF.
If the scan results for the selected BSS are available, use those to
update the RSN state machine AP RSNE/RSNXE similarly to the way this is
done with wpa_supplicant selects the BSS instead of clearing that
information in the RSN state machine.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for a new BSS entry to be added for the
hidden-SSID-OWE-BSS when running a new scan after having previously
learned the hidden SSID during a previous OWE connection attempt. That
new entry would not necessarily have the WPA_BSS_OWE_TRANSITION flag set
and that would result in not being able to recognize the appropriate OWE
profile when checking the association event against the transition mode
configuration.
Fix this by updating the BSS entry for OWE transition mode information
for the cases where this might happen.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Print correct expected AP MLD address information when the AP MLD
address validation fails in Authentication frames during external
authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Fail MLD address validation only if Authentication frames IE parsing
actually failed, i.e., ignore all unknown IEs.
This is needed to avoid authentication failure when the Authentication
frames include IEs which are not handled by ieee802_11_parse_elems(),
e.g., AKM Suite Selector IE.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Export the "he" network profile item to be configurable from external
client side, like wpa_cli or NetworkManager. This follows the earlier
changes to allow the previously internal-only parameter (e.g., vht) to
be used for additional purposes for AP mode.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>