This makes the test case a bit more likely to be able to complete with
S1G being enabled in mac80211_hwsim. However, the 15 second P2P protocol
timeout itself can be hit in this type of a case and the test case will
still fail every now and then if all mac80211_hwsim supported channels
are included.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This tests an error, where the p2p_long_listen information from the
wrong device was used internally in wpa_supplicant when using the
separate P2P Device interface.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
These test cases verify that there is no duplicate processing of P2P
Action frames while operating in a P2P group.
Signed-off-by: Jouni Malinen <j@w1.fi>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Test different delay intervals between the INTERFACE_DISABLED event
and the INTERFACE_ENABLED event for discovery_and_interface_disabled.
Previously, only a delay of 1 second was used, in which case the
scan results for the P2P_FIND operation were received after the
interface was enabled again, and the case the scan results were
received while the interface was disabled was not covered.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The test cases discovery_ctrl_char_in_devname and discovery_group_client
tried to allow three P2P_FIND instances to be used before reporting an
error. However, this did not really work properly since the second and
third attempts would likely fail to start the initial special P2P_FIND
scan due to an already ongoing p2p_scan operation. Fix this by stopping
the previous P2P_FIND and waiting for the scan to complete if a retry is
needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the previous commit works correctly by forcing a
P2P_LISTEN command execution to be interupted by a P2P_FIND command
timed in a manner that forces it to show up before the kernel ROC has
started for the Listen.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case could fail if there were old BSS entries remaining in
cfg80211 scan results. That happened, e.g., when running test cases in
the following sequence: "discovery_social_plus_one discovery_auto".
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Modify discovery_stop to use global control interface when calling
P2P_FLUSH.
2. Modify p2p_listen_and_offchannel_tx to use the global control
interface when waiting for P2P PD event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This verifies that offchannel TX (PD in this specific case) does not
stop ongoing long P2P_LISTEN operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow three P2P_FIND attempts for discovering the GO on a non-social
channels since the single Probe Response frame can be missed easily
under heavy CPU load.
Signed-off-by: Jouni Malinen <j@w1.fi>
It turned out that the initial test case found the GO based on the
initial full scan instead of the progressive search part. Fix this by
started the GO only after the initial full scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like some of the discovery_* test cases have been failing every
now and then on the virtual server and the one second timeout could have
been a bit too short to cover some possible timing cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not really perfect, but something to get a bit more testing
coverage.. For proper discoverability mechanism validation, the P2P
client would need to go to sleep to avoid acknowledging the GO
Negotiation Request frame. Offchannel Listen mode operation on the P2P
Client with mac80211_hwsim is apparently not enough to avoid the
acknowledgement on the operating channel, so need to disconnect from the
group which removes the GO-to-P2P Client part of the discoverability
exchange in practice.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows more consistent interface to be used regardless of which
P2P driver design is used (especially for P2P management operations
over netdev vs. dedicated P2P_DEVICE).
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P_PROV_DISC fails if the peer is not fully discovered and the previous
version of the test cases did not force this (i.e., it could have
started PD just based on having seen a Probe Request frame from the
peer).
Signed-hostap: Jouni Malinen <j@w1.fi>
