On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
Commit adcd7c4b0b ('nl80211: Support
vendor scan together with normal scan') made the drv->scan_state updates
for NL80211_CMD_NEW_SCAN_RESULTS and NL80211_CMD_SCAN_ABORTED
conditional on drv->last_scan_cmd being NL80211_CMD_TRIGGER_SCAN. This
missed the part about the possibility of last_scan_cmd == 0 and an
externally started cfg80211 scan is ending. This could leave
drv->scan_state into SCAN_STARTED state even after the scan was
completed. Consequently, hwsim test cases could get stuck in reset()
handler waiting for scan to terminate.
Fix this by updating drv->scan_state also in drv->last_scan_cmd == 0
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Skipping the scan altogether will hurt auto-reconnect. Also move the PNO
check down since the scan might be canceled for other reasons before we
defer it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of fetching all scan results to a temporary buffer, debug print
scan result dump directly from the message handler function one BSS at a
time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be parsed at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv has never really been fully up-to-date with the wpa_supplicant
driver interface extensions. This does not seem like something that
would change in the future either, so document this reduced
functionality as a potential drawback.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a theoretical resource leak on exit path if wpa_priv is
killed while there is a wpa_supplicant process using it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids some valgrind warnings about use of uninitialized memory in
cases where a struct may have padding octets between the fields.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of some dependencies on how extra octets at the end of the
struct sockaddr_un get "uninitialized" consistently by only using the
exact length of the address data from the recvfrom() call. This resolves
number of valgrind warnings about use of uninitialized memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to work with many wpa_supplicant use cases,
e.g., due to use of TDLS or RSN pre-authentication needing a separate
l2_packet socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases verify that there is no duplicate processing of P2P
Action frames while operating in a P2P group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be checked at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This untangles the NL80211_CMD_GET_SURVEY handler loop from
NL80211_CMD_GET_SCAN processing so that the per-channel noise
information can be fetched with a common function to a local data
structure that can then be easily used to update individual scan results
(a single BSS) instead of having to go through a full set of scan
results. This is a step towards optimizing scan result fetching without
having to allocate memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the ap_wds_sta test case to cover post-reassociation case
(both with and without Authentication frame exchange) and add similar
test cases to cover open and WEP cases in addition to this existing
WPA2-PSK test case.
These cover functionality testing for the previous fix in
reassociation-without-new-authentication case. In addition, these find a
new mac80211 issue for the WEP + 4addr combination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are used only within driver_wired_common.c now at the end of the
refactoring changes, so there is no need to make these helper functions
available outside driver_wired_common.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses libnl3 to communicate with the macsec module available on
Linux. A recent enough version of libnl is needed for the macsec.h file
(which is not yet available in a formal libnl release at the time of
this commit).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Refactor the common parts of wired drivers code into a shared file, so
that they can be reused by other drivers. The macsec_qca driver already
contains a lot of code duplication from the wired driver, and the
macsec_linux driver would do the same. A structure to hold data common
to all wired drivers is added and used in all these drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.
This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.
Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN command can be used to
abort an ongoing scan that was started with
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that AP does not break PMF-enabled connection due to injected
Authentication frame. This is a regression test for
NL80211_FEATURE_FULL_AP_CLIENT_STATE changes resulting in dropping the
key in such a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to write hwsim test cases to verify management
frame processing sequences with dropped or modified frames. When
ext_mgmt_frame_handling is used, this new command can be used to request
hostapd to process a received a management frame, e.g., based on
information reported in the MGMT-RX events.
This is more or less identical to the earlier wpa_supplicant commit
4de70e2330 ('Add MGMT_RX_PROCESS test
command for wpa_supplicant'), but for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.
It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").
wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.
Signed-off-by: Will Glynn <will@willglynn.com>
