Even though scan_ssid should not really be set for wildcard SSID,
better verify that here explicitly insead of assuming that the
SSID is set.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The source code compiles into different objects depending on
the contents of .config. Therefore, the objects should depend
on .config.
Previously, only the executables depended on .config. This meant
that they were re-linked when .config changed. But that relink
process used the old (and now wrong) objects.
Scan wasn't initiated in case the config contained only networks without
scan_ssid. In such a case we want scan to be initiated without any SSIDs
to actively scan but include all the SSIDs in the filter list. Also
added some debug logs to easily see which SSIDs were included in which
list.
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Some drivers do not handle concurrent remain-on-channel operation
requests, so run p2p_stop_find() prior to starting p2p_listen. This
addresses some issues with P2P_LISTEN command being issues again
while already in Listen state.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In AP mode, authentication algorithm is reset in
hostapd_config_defaults_bss() and never set to the configured one. This
would pass the default auth_algs (OPEN|SHARED) to driver regardless of
what the wpa_supplicant configuration is requesting.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The libnl_2 library uses static linking and different path for
header files in the Android ICS release.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P IE was incorrectly added in wpa_supplicant AP mode even if P2P
function was not actually enabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant AP mode is used, WPS was enabled by default
regardless of security mode. This is not desired for WEP, so change
the AP configuration to enable WPS only for open and WPA/WPA2-Personal
networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This has been obsoleted by the more generic Linux WEXT (driver_wext.c)
support. The hostap and madwifi driver wrappers can now be used only
with hostapd. The old station interface remains available in releases up
to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver wrappers broadcom, iphone, osx, and ralink have not been
maintained for a while and it does not look like they will be in the
future either. As such, remove them from the development branch. The
previous versions will be included in older releases up to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use a driver_ndis.c specific initialization function to fill in the
wpa_driver_ops information to make it easier to modify struct
wpa_driver_ops in the future. Being able to build driver_ndis.c
with MSVC was the only reason for having to maintain the same order
of function pointers in struct wpa_driver_ops and for having to
update driver_ndis.c for all changes in that structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
This code has not been maintained for years and there is no plan on
doing so either in the future. The Qt4-based wpa_gui-qt4 version can be
used as a replacement for this older wpa_gui version.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_supplicant_rsn_preauth_scan_results() needs to be called to
update RSN pre-authentication candidates. This cannot be done before
the wpa_supplicant_connect() call on the first association, but when
trying to figure out whether to roam, it is fine to do so for the
case when roaming is skipped.
Signed-hostap: Jouni Malinen <j@w1.fi>
In scan.c, merge a channel's noise value into the scan results. When
comparing scan results, compute the signal-to-noise ratio and use it
when available. Prefer a 5 GHz network if its SNR is really big (> 30)
or if its SNR is relatively close to the other network's.
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
Converts from a string to a control request enum when input
from a control interface is received. Will be used by a
subsequent patch.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Add a D-Bus signal for EAP SM requests. This signal is emitted on the
Interface object so that clients only have to listen to one object for
requests rather than to all network objects. This signal is analogous
to the socket control interface's CTRL-REQ- request.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Control requests will be extended for non-EAP uses later, so it makes
sense to have them be generic. Furthermore, having them defined as an
enum is easier for processing internally, and more generic for control
interfaces that may not use field names. The public ctrl_req_type /
field_name conversion function will be used later by the D-Bus control
interface too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
At least with driver_test.c, the BSS table may not include frequency
information. In such a case, we need to skip rate set matching during
BSS selection to avoid rejecting valid AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
The interface may not yet have been set to P2P client mode immediately
after GO Negotiation when doing the scan before association request.
Consequently, the scan request in this state has to specify that the
specific P2P probe mode is used to disable IEEE 802.11b rates.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_supplicant dbus objects are currently difficult to use with
GDBusProxy. This is because they do not follow the dbus standard in
emitting the PropertiesChanged signal on the standard D-Bus properties
interface, so GDBusProxy stores stale property values.
Fix this by raising PropertiesChanged on the standard interface.
For backwards compatibility, the existing custom PropertiesChanged
signals are not removed; I anticipate them being removed in a future
major release.
See
http://lists.freedesktop.org/archives/dbus/2011-August/014593.html
for more info.
Signed-off-by: Daniel Drake <dsd@laptop.org>
P2P Client did not show correct frequency in the control interface
event P2P_EVENT_GROUP_STARTED. Fix that by using the frequency from
the BSS table or association event.
This patch stops any on-going "p2p_find" on creating an Autonomous GO.
This is already taken care in case of invoking a persistent GO. GO as
such will be advertising via the beacons for other devices to discover.
So normally the GO doesn't need to do a p2p_find until and unless it
wants to invite a P2P Client. In case of Invite scenario, logically it
is better to do a explicit discover [via user intervention] after the GO
is created. This patch will help to reduce battery wastage [due to
p2p_find operations] in scenarios where user creates a GO and doesn't
initiate a connection.
Once PBC overlap detected when using dynamic group interfaces, the wpa_s
corresponding to P2P group interface is freed. This patch avoids
accessing the wpa_s data structure after it is freed. This fixes a
possible crash in P2P client role in such a case.
The persistent_reconnect configuration parameter was used to decide
whether to accept invitation to re-establish a persistent group.
However, this was not being advertised in the Group Capability bitmap.
Add the Persistent Reconnect bit based on this configuration to GO
Negotiation frames and Beacon/Probe Response frames from the GO.
Use capability information to decide whether to perform a given TDLS
operation internally or through mgmt-frame Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
