I tried these commands:
./wpa_cli -i wlan0 p2p_group_add
./wpa_cli -i wlan0 p2p_find
The second one results in following messages because it is invalid
operation.
-------
nl80211: Scan trigger failed: ret=-95 (Operation not supported)
P2P: Failed to start p2p_scan
-------
But the second one shows "OK" on control console.
This patch makes it to show "FAIL".
Previously, both NULL and ff:ff:ff:ff:ff:ff addr were used in various
places to indicate default/broadcast keys. Make this more consistent
and useful by defining NULL to mean default key (i.e., used both for
unicast and broadcast) and ff:ff:ff:ff:ff:ff to indicate broadcast
key (i.e., used only with broadcast).
The destination address for p2p_serv_disc_resp must always be set
to an individual MAC address unlike p2p_serv_disc_req which may use
00:00:00:00:00:00 to indicate wildcard query. As such, we should not
try to check for this special case here.
Replacing the BSSID with 'any' has never worked with wps_reg
command, so better not claim it could work. In addition, reject
this is wpa_supplicant to make it clearer that the operation
fails.
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.
The new failure codes for P2P_CONNECT:
FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).
FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
This cleans up debug log from unnecessary entries when using
wpa_cli/hostapd_cli or other ctrl_iface monitors that PING
periodically to check connectivity.
Instead of build time options (CONFIG_WPS_TESTING_EXTRA_CRED and
CONFIG_WPS_EXTENSIBILITY_TESTING), use a single build option
(CONFIG_WPS_TESTING) and runtime configuration of which testing
operations are enabled. This allows a single binary to be used
for various tests.
The runtime configuration can be done through control interface
with wpa_cli/hostapd_cli commands:
Enable extensibility tests:
set wps_version_number 0x57
Disable extensibility tests (WPS2 build):
set wps_version_number 0x20
Enable extra credential tests:
set wps_testing_dummy_cred 1
Disable extra credential tests:
set wps_testing_dummy_cred 0
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
This is mainly designed for testing and allows p2p_connect join auth
to be used to accept a specific invitation to an active group that
may be received in the future.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
Despite comments in the wpa_config_update_prio_list(struct wpa_config
*config) telling that it is called "if priority for a network is
changed", it is apparently not.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
