Since this function needs to allocate memory, it might fail. Check that
the returned memory pointer is not NULL before trying to parse the
output.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this function could return NULL if the parameter issued to it were
NULL, that does not really happen here. Anyway, since this can result in
a warning from a static analyzer that does can see the return NULL
without fully understanding what it means here, check the return value
explicitly against NULL to avoid false warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This command was documented as having the Server URL parameter as
optional, but the implementation did not match that. Allow this
parameter to be left out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The error print could not have been reached since the exact same
condition was verified above and exit(0) is called if the command line
is invalid.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of an EAP session entry, so avoid flushing the
cached session when only these parameters are changed. This is mainly to
allow forced roaming or network selection changes without causing fast
reauthentication to be disabled if the changes are done during RSN
association that used EAP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The addition operator is of higher precedence than the ternary
conditional and the construction here needs to use parentheses to
calculate the buffer length properly when generating test frames with
BIP protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the configured credential includes a username without '@' (i.e., no
realm) in it and a realm, combine these to form the EAP-Request/Identity
value as "<username>@<realm>" for EAP-TLS. This was already done for
EAP-TTLS as part of the anonymous NAI conversion, but EAP-TLS could have
ended up using a username without any realm information which would be
unlikely to work properly with roaming cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow updated Interworking behavior that adds the
realm to the EAP-Response/Identity value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since commit cb05808c46 ('nl80211: Generic
Linux master interface support for hostapd'), hostapd is listening for
EAPOL frames on any master which the interface is enslaved under.
This commit allows hostapd to support network hierarchy in which the
interface is enslaved under some master which in turn is enslaved under
a bridge.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Incorrect path and file name was used in the openssl command to generate
one of the OCSP responses. Also fix
ap_wpa2_eap_tls_intermediate_ca_ocsp_multi to expect success rather than
failure due to OCSP response. Based on the test description, this was
supposed to succeed, but apparently that root_ocsp() bug prevented this
from happening.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Upon receiving FST setup request on old band, the peer is searched on
new band. The assumption is that MB IE from this peer on new band
previously received either in assoc event or in FST setup request.
There are cases in which above assumption doesn't work, peer is not
found and session setup fails. For example:
- STA connects over 11ac. Due to driver limitation, MB IE is not included
in assoc event
- STA connects over 11ad. MB IE included in assoc event.
- FST session established on 11ac band, with AP as initiator. i.e. FST
setup request sent in AP=>STA direction. STA searches for peer's (AP)
MB IE on 11ad band which exists.
- FST switch occur
- FST session established on 11ad band, with STA as initiator. i.e. FST
setup request sent in STA=>AP direction. AP searches for peer's (STA)
MB IE on 11ac band which are absent.
For fixing the above, consider also peers without MB IE as candidates in
the search algorithm.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
The existing implementation in p2p_ctrl_set used a hard-coded operating
class 81 which is only suitable for the social channels in the 2.4 GHz
band, and will not work for the social channel in the 60 GHz band.
Extend this by adding an optional op_class argument to P2P_SET
listen_channel. If not specified, use the default value of 81 to match
existing behavior.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
In the 60 GHz band, service discovery management frames are sent over
the control PHY and have a smaller maximum frame size (IEEE Std
802.11ad-2012, 21.4.3.2). Fix the code to use sufficiently small
fragment size when operating in the 60 GHz band.
The 60 GHz fragment size (928) is derived from the maximum frame size
for control PHY (1023) and subtracting 48 bytes of header size, and some
spare so we do not reach frames with the absolute maximum size.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.
Signed-off-by: Naveen Singh <nasingh@google.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
There is a race condition in which AP might receive the EAPOL-Start
frame (from the just-associated station) before the TX completion of the
Association Response frame. This in turn will cause the EAPOL-Start
frame to get dropped, and potentially failing the connection.
Solve this by saving EAPOL frames from authenticated-but-not-associated
stations, and handling them during the Association Response frame TX
completion processing.
Signed-off-by: Eliad Peller <eliad@wizery.com>
hostname and port can now be specified when using wpaspy.Ctrl, so we can
connect to remote clients now.
This can also be tested using test.py application with
./test.py <hostname> <port>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Return a list of the available interfaces (the main BSS) and optionally
with ctrl_iface when the optional "ctrl" parameter is included. This is
useful when using UDP ctrl_iface and add interfaces using the ADD
command. After that we need to know which UDP port was assigned for the
control interface for the added interface.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Set up the real ctrl_interface for UDP after having selected the port.
This is in format: udp:<port_no>. This is needed to get accurate
interface <-> udp_port mapping.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
"INTERFACES ctrl" can now be used to fetch a list of network interfaces
and their control interfaces, e.g., to fetch the UDP port information
for the control interface.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This allows the UDP port to be set for the per-interface and global
control interfaces. The format is: udp:<port_no>
For example:
hostapd -ddt -g udp:8888
And in the configuration file:
ctrl_interface=udp:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add UDP support for ctrl_iface:
New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
And hostapd_cli usage:
hostapd_cli -i localhost:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is preparation for sharing a single implementation for ctrl_iface
functionality in wpa_supplicant and hostapd.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Extend the previously per-interface UDP ctrl_iface functions
(attach/detach/send) to support operations on the global interface as
well.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This allows the UDP port to be set for the per-interface and global
control interfaces. The format is: udp:<port_no>
For example:
wpa_supplicant -Dnl80211 -ddt -g udp:9888
And in the configuration file:
ctrl_interface=udp:9877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Update the peer WFD IE information based on WFD elements received in
Provision Discovery Response and GO Negotiation Response frames.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Make sure wpas_p2p_init_go_params() respects the p2p_ignore_shared_freq
configuration option. Choose currently used frequencies only if this
option is not set, or if there are no unused channels left.
Signed-off-by: Eliad Peller <eliad@wizery.com>
In case a Probe Request frame is received from a known peer P2P Device,
update the listen channel based on the P2P attributes in the Probe
Request frame. This can be useful for cases where the peer P2P Device
changed its listen channel, and the local P2P device is about to start a
GO Negotiation or invitation signaling with the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When p2p_find is stopped, send request to the driver
in order to cancel an ongoing scan if there is one.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
